Page 1 Command Manual NWA-033623-001 ISSUE 8.1...
Page 2 NEC Corporation reserves the right to change the specifications, functions, or features, at any time, without notice. NEC Corporation has prepared this document for use by its employ- ees and customers. The information contained herein is the property of NEC Corporation and shall not be reproduced without prior written approval from NEC Corporation.
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION PURPOSE ........................ OUTLINE OF THIS MANUAL ................... TERMS IN THIS MANUAL ..................PBX SYSTEM DESIGNATION ..................ATTENDANT CONSOLE NAME ..................TERMINAL NAME ......................COUNTRY REFERENCE ....................REFERENCE MANUAL ................... Chapter 1 HOW TO USE CAT CAT AND PCPro ...................... CAT KEY FUNCTIONS ....................
Page 4 [CM04] SETTING OF SYSTEM SERVICES ............3-10 [CM05] BLADE TYPE, TRUNK BLADE NUMBER, HIGHWAY CHANNEL FOR ISDN DATA COMMUNICATION ............3-30 [CM08] BASIC SERVICES ..................3-33 [CM0B] LAN DATA ASSIGNMENT ................3-90 [CM0C] UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE ....................3-128 [CM10] STATION NUMBER, TRUNK NUMBER, BLADE NUMBER .......
Page 5 [CM40] CPU BUILT-IN MODEM ................3-333 [CM41] SYSTEM TIMER DATA ................3-334 [CM42] SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION/CODEC LIST ..............3-367 [CM42] SYSTEM COUNTER DATA/PAD DATA ............. 3-368 [CM42] TRUNK RESTRICTION CLASS CONVERSION ......... 3-376 [CM42] CODEC LIST ....................3-378 [CM43] PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC...
Page 6 [CM73] MEMORY ALLOCATION FOR STATION SPEED DIALING ....... 3-475 [CM74] STORED NUMBER FOR STATION SPEED DIALING ....... 3-479 [CM76] DIGIT CONVERSION ON DID CALL ............3-483 [CM77] STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT ..... 3-499 [CM78] DESTINATION OF SPLIT CALL FORWARDING ........3-504 [CM81] TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION...
Page 7 [CME0] RESET/INSTANT SYSTEM CHANGEOVER ..........3-646 [CME1] CPU MEMORY CHECK SUM DISPLAY ............. 3-649 [CME4] STATION SERVICE STATUS DISPLAY ............. 3-650 [CME5] STATION, TRUNK LINE MAKE BUSY ............3-653 [CME6] CALL FORWARDING SET/RESET FROM PCPro/CAT ......3-655 [CME7] PASSWORD LEVEL ................... 3-657 [CME8] UPDATING OF ACCESS BLADE FIRMWARE ...........
Page 8 THIS PAGE LEFT BLANK INTENTIONALLY. NWA-033623-001 Rev.8.1 91toc001.fm...
Page 9: Introduction
INTRODUCTION PURPOSE INTRODUCTION PURPOSE This manual explains all of the commands required for programming the SV8300, using the Customer Administration Terminal (CAT) or PCPro. NWA-033623-001 Rev.8.1 91ch0001.fm...
Page 10: Outline Of This Manual
INTRODUCTION OUTLINE OF THIS MANUAL OUTLINE OF THIS MANUAL This manual consists of three chapters. The following paragraphs summarize Chapters 1 through 3. CHAPTER 1 HOW TO USE CAT This chapter explains how to use the Customer Administration Terminal (CAT) which is used as the man-machine interface with the PBX.
Page 11: Terms In This Manual
PBX SYSTEM DESIGNATION PBX system is usually designated as “PBX” or “system”. When we must draw a clear line between the PBX systems, they are designated as follows. SV8300 : UNIVERGE SV8300 SV8500 : UNIVERGE SV8500 SV7000 : UNIVERGE SV7000...
Page 12: Terminal Name
INTRODUCTION TERMS IN THIS MANUAL TERMINAL NAME The following digital multi-function terminals are designated as “Multiline Terminal” usually, unless we need to mention the type of terminal in particular. TERMINAL NAME PRODUCT NAME term term Multiline Digital Multiline Terminal 70 (Elite) Terminal term 75 (Series E)
Page 13: Country Reference
INTRODUCTION TERMS IN THIS MANUAL COUNTRY REFERENCE The exclusive commands for specific country are described as follows; [Asia] [Mexico Only] [Australia Only] [New Zealand Only] [Australia/Argentina] [North America Only] [Australia/Europe] [North America/Latin America] [Australia/France] [North America/EU] [Australia/New Zealand] [Not used in Australia/North America] [Australia/North America] [Not used in Australia/North America/UK] [Brazil (900 )/New Zealand]...
Page 14: Reference Manual
INTRODUCTION REFERENCE MANUAL REFERENCE MANUAL Refer to the following manuals for information on each service programming. System Manual: Contains the system description and the programming procedure of the SV8300 System. Programming Manual: Contains procedure for programming each business, hotel, ISDN, OAI and WCS feature. Networking Manual: Contains the system description and the programming procedure for the CCIS, Q-SIG and Remote UNIT over IP System.
Page 15: Chapter 1 How To Use Cat
UNIVERGE SV8300 Command Manual HOW TO USE CAT Chapter This chapter explains how to use the Customer Administration Ter- minal (CAT) which is used as the man-machine interface with the PBX. NWA-033623-001 Rev.8.1 91ch1001.fm...
Page 16: Cat And Pcpro
Chapter 1 HOW TO USE CAT CAT AND PCPro CAT AND PCPro In this system, the Customer Administration Terminal (CAT) or PCPro is used for programming the system data. The CAT is a digital multi function telephone (Multiline Terminal) which is equipped with function keys, a dial pad and LCD and interfaces with the system via the CPU blade.
Page 17: Cat Key Functions
Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT KEY FUNCTIONS In the CAT mode, each key on the Multiline Terminal is automatically assigned as shown in figure below. Page 1-15 For the function of each key, see “CAT Function Keys”.
Page 18 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Key Assignment (Old layout) [For 8300R1] ← [For 8300R2 software or later] ← DT300/DT700 Series ← ← NOTE: The keys marked by “*” are available when using 8300R2 software or later. Continued on next page NWA-033623-001 Rev.8.1 91ch1001.fm...
Page 19 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Key Assignment (Old layout) term term Series i Series i Exit Help ← − − Directory Message PQRS WXYZ ← DTR-32D-1 NOTE: The keys marked by “*” are available when using 8300R2 software or later. Continued on next page NWA-033623-001 Rev.8.1 91ch1001.fm...
Page 20 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 16 Line/Trunk Feature Keys + 16 One Touch Keys (CM12 Y=24 2nd data=7) CAT Key Assignment (Old layout) Exit Help ← − 1 2 3 − 4 5 6 7 8 9 A 0 B ←...
Page 21 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 24 Line/Trunk Feature Keys + 8 One Touch Keys (CM12 Y=24 2nd data=0) CAT Key Assignment (Old layout) Exit Help ← − 1 2 3 − 4 5 6 7 8 9 A 0 B ←...
Page 22 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Key Assignment (New layout) DT300/DT700 Series NOTE: The keys marked by “*” are not available when using 12 keys kit. Continued on next page NWA-033623-001 Rev.8.1 91ch1001.fm JUNE/15/2011...
Page 23 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 16 Line/Trunk Feature Keys + 16 One Touch Keys (CM12 Y=24 2nd data=7) CAT Key Assignment (New layout) term term Series i Series i Exit Help ← − − Directory Message PQRS WXYZ...
Page 24 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 24 Line/Trunk Feature Keys + 8 One Touch Keys (CM12 Y=24 2nd data=0) CAT Key Assignment (New layout) term term Series i Series i Exit Help ← − − Directory Message PQRS WXYZ...
Page 25 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • 16 Line/Trunk Feature Keys + 16 One Touch Keys (CM12 Y=24 2nd data=7) • 24 Line/Trunk Feature Keys + 8 One Touch Keys (CM12 Y=24 2nd data=0) CAT Key Assignment (New layout) Exit Help ←...
Page 26: Cat Key Assignment Of Multiline Terminal Soft Key
Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT KEY ASSIGNMENT OF MULTILINE TERMINAL SOFT KEY CAT key assignment of Multiline Terminal soft key can be used when using 8300R3 software or later. The screen transition of CAT key assignment is as follows. •...
Page 27 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS - Before setting the second data (after setting the first data) - When setting the second data - After setting the second data 1-13 NWA-033623-001 Rev.8.1 91ch1001.fm JULY/17/2009...
Page 28 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS • DESI-less (DT330 DESI-less, DT730 DESI-less, DT710 DESI-less)/DT750 - DT330 DESI-less/DT730 DESI-less can be switched LCD screens between the front page and the fourth page with a press of the Scroll Key. - DT710 DESI-less can be displayed the front page only.
Page 29 Chapter 1 HOW TO USE CAT CAT KEY FUNCTIONS CAT Function Keys FUNCTION KEY MEANING Command entry start Execution of data write Cancel of key operation (Clear entry) Display of next data (Step forward) Separator; to be entered between two different data such as first/second data (For example CM72) –...
Page 30: Cat Mode Setting Procedure
Chapter 1 HOW TO USE CAT CAT MODE SETTING PROCEDURE CAT MODE SETTING PROCEDURE To set CAT mode: term term term • For DT300/DT700 Series/D 70 (Elite)/D 75 (Series E)/D 85 (Series i) 1. Press the Keys on the terminal in the following order when the terminal is on idle state. "C"...
Page 31 Chapter 1 HOW TO USE CAT CAT MODE SETTING PROCEDURE To clear the CAT mode: term term term • For DT300/DT700 Series/D 70 (Elite)/D 75 (Series E)/D 85 (Series i) 1. Press EXIT key while “COMMAND= –” is displayed on the LCD. 1.
Page 32: Notice On Cat Mode
Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE NOTICE ON CAT MODE The CAT is used in on-line. Therefore, offline commands cannot be accessed from the CAT. To use the CAT after clearing all system data, perform the following operations on the system. 1.
Page 33 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE The following data is automatically set when loading the standard system data. Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE – System Data All Clear SRAM area All Clear 0101...
Page 34 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 172.16.1.1 IP address of VOIP Port for control packet of Unit No. 01 255.255.0.0 Subnet Mask of VOIP Port for con- trol packet of Unit No.
Page 35 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 172.16.1.8 IP address 7 of VOIP Port for voice control of Unit No. 01 172.16.1.9 IP address 8 of VOIP Port for voice control of Unit No.
Page 36 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Command List Set by Standard System Data Assignment COMMAND Y NUMBER 1ST DATA 2ND DATA REMARKS CODE 172.16.3.6 IP address 5 of VOIP Port for voice control of Unit No. 03 172.16.3.7 IP address 6 of VOIP Port for voice control of Unit No.
Page 37 Chapter 1 HOW TO USE CAT NOTICE ON CAT MODE Do not change or delete the My Line number (set by CM10 Y=00) of the CAT, during CAT mode. There are no limitations on the number of Multiline Terminals in the system that can be programmed to allow CAT capability.
Page 38: Cat Operation
Chapter 1 HOW TO USE CAT CAT OPERATION CAT OPERATION When setting the system data, it is necessary to enter the following three kinds of data. • Command Code • First Data • Second Data The operation is explained below. To confirm the existing system data + Command Code + + First Data +...
Page 39 Chapter 1 HOW TO USE CAT CAT OPERATION The examples of data setting are described below. Example in the case that station number 300 is to be assigned to Physical Port No. 010101 and station number 301 to Physical Port No. 010102 by CM10 Y=00. Example of CAT Operation (Display) STEP 1...
Page 40 Chapter 1 HOW TO USE CAT CAT OPERATION Example of correcting the data entry In STEP 5 in the above (1) example, when has been pressed after entering “010102” by mistake, press . Then the state returns to STEP 4. STEP1: CM10 Y=00 has been entered and has been 1000>...
Page 41 Chapter 1 HOW TO USE CAT CAT OPERATION Example of deleting station number “300” assigned to Physical Port No. 010101 after completing all the operation in the above (1) example. STEP1: Press COMMAND= STEP2: Enter “1000”. (Command Code) COMMAND=10 STEP3: Press 1000>...
Page 42: Error Messages
Chapter 1 HOW TO USE CAT ERROR MESSAGES ERROR MESSAGES When an operation is incorrect, or wrong data is entered, an error message is displayed on the LCD. Error messages and their meanings are shown below. Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION CM DIGIT ERROR [0]/...
Page 43 Chapter 1 HOW TO USE CAT ERROR MESSAGES Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION SD CODE NOT Second data which is not allowed in Check whether the second data is ALLOWED/CODE the current status. available or not. NOT ALLOWED NOTE CM CODE NOT USED/ The command code entered is not in...
Page 44 Chapter 1 HOW TO USE CAT ERROR MESSAGES Error Messages ERROR MESSAGE MEANING OF MESSAGE ACTION WRONG The data stored in the memory is Clear the present data by entering wrong. This message is displayed “CCC”, or enter the correct data. when too many digits are entered.
Page 45 UNIVERGE SV8300 Command Manual PRECAUTION Chapter This chapter explains precautions for using commands, such as conditions for using commands, method of setting on-line/off-line mode, method of system data/SRAM data all clear, port allocation, password entry, and nation code assignment. NWA-033623-001 Rev.8.1 91ch2001.fm...
Page 46: Chapter 2 Precaution
Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS CONDITIONS FOR USING COMMANDS Some commands require a system reset after data setting, and others cannot be assigned/changed unless the system is in off-line mode (a state in which call processing is at a halt). These commands are shown in the following table, categorized according to the conditions for their use.
Page 47 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which require a CM05 Y=2 Blade Type, Trunk Blade Number, Highway reset of the CPU blade after Channel for ISDN Data Communication data setting. CM08>335, 391, 420, 592, Basic Services •...
Page 48 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which require a CM04 Y=10-59>01, 02 Setting of System Services reset of the blade after data CM05 Y=0, 1 Blade Type, Trunk Blade Number, Highway setting.
Page 49 Chapter 2 PRECAUTION CONDITIONS FOR USING COMMANDS Conditions for Using Commands CONDITION COMMANDS MEANINGS Commands which can be CM00 System Data Memory All Clear/SRAM Clear used only under Off-Line CM01 System Data Memory Partial Clear mode of the CPU blade. See CM0B Y=000 LAN Data Assignment “METHOD OF SETTING...
Page 50: Method Of Setting On-Line/Off-Line Mode
Chapter 2 PRECAUTION METHOD OF SETTING ON-LINE/OFF-LINE MODE METHOD OF SETTING ON-LINE/OFF-LINE MODE FOR CPU BLADE • Setting Off-line mode Set SENSE switch on the CPU blade to “E” or “F”. Press RESET switch on the CPU blade. • Setting On-line mode Set SENSE switch on the CPU blade to “0-4”.
Page 51 Chapter 2 PRECAUTION METHOD OF SETTING ON-LINE/OFF-LINE MODE NOTE: The data setting is as follows. • When the SENSE switch is set to E (default setting): RS-232C CONNECTION IP CONNECTION (RS1/RS2 port) (ETHERNET/VOIP port) Data speed: 9600 bps • Maintenance port Data length: 8 bits Data speed: Auto Negotiation Parity: None...
Page 52: Method Of System Data/Sram Data All Clear
Chapter 2 PRECAUTION METHOD OF SYSTEM DATA/SRAM DATA ALL CLEAR METHOD OF SYSTEM DATA/SRAM DATA ALL CLEAR When starting up the system firstly, adding on a unit, replacing the CPU, or all the system data and SRAM data must be cleared. STEP1: Make the system off-line mode.
Page 53: Password Entry
Chapter 2 PRECAUTION PASSWORD ENTRY PASSWORD ENTRY In a system with password service, a maintenance person is required to enter an authorization level number (Password Level) and appropriate password prior to engaging in programming the system data with the PCPro/CAT. A maximum of eight (8) Password Levels can be set up. The number of commands that the maintenance person can access is determined by the Password Level.
Page 54 Chapter 2 PRECAUTION PASSWORD ENTRY Table below shows the example for the Password Level Table. Example of Password Level Assignment MAINTENANCE PASSWORD ACCESIBLE COMMANDS PERSONNEL LEVEL Level 7 All commands Level 4 CM05, 08, 0B-13, 15, 30, 35, 36 Level 3 CM08, 0B-13, 15, 30, 35 Level 2 CM10, 11, 30, 35...
Page 55: Nation Code Assignment
Chapter 2 PRECAUTION NATION CODE ASSIGNMENT NATION CODE ASSIGNMENT With the Nation Code assigned, the system offers the particular services to the users of each country. For Australia or New Zealand, appropriate nation code to the user should be assigned by CM31 Y=0 as shown below.
Page 56: System Data Backup
Chapter 2 PRECAUTION SYSTEM DATA BACKUP SYSTEM DATA BACKUP CAUTION • If you operate as follows without system data backup after system data setting or service memory setting (registration of the features such as “Call Forwarding” and “Speed Dialing” from a station), the data that has been set is invalid. You must execute the system data backup before the following operations.
Page 57: Chapter 3 Command Description
UNIVERGE SV8300 Command Manual COMMAND DESCRIPTION Chapter This chapter explains the function, precaution, assignment proce- dure and data table of each command. Explanations are given in numerical and alphabetical order of the command code. NWA-033623-001 Rev.8.1 91ch3001.fm...
Page 58: How To Read This Chapter
Chapter 3 COMMAND DESCRIPTION HOW TO READ THIS CHAPTER HOW TO READ THIS CHAPTER HOW TO READ THIS CHAPTER Information about each command is presented in the following order: FUNCTION: The function of the command. PRECAUTION: Precautions related to assigning data. ASSIGNMENT PROCEDURE: The procedure for assigning data in CAT mode.
Page 59: System Data Memory All Clear/Sram Clear
CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR/SRAM OFF LINE CLEAR FUNCTION: This command is used to confirm that system data memory (RAM) area billing memory area (SRAM) can be written-in/read-out, and to assign the default to the RAM area or SRAM area. PRECAUTION: This command can only be used in off-line mode.
Page 60 CM00 COMMAND CODE TITLE: SYSTEM DATA MEMORY ALL CLEAR/SRAM OFF LINE CLEAR DATA TABLE: 1ST DATA 2ND DATA DATA MEANING DATA MEANING System data memory all clear Clear SRAM area all clear Clear [8300R2] NOTE: Be careful handling CM00>02. Because all stored data in a SRAM area is cleared when the SRAM area memory clear is executed by this command.
Page 61: System Data Memory Partial Clear
CM01 COMMAND CODE TITLE: OFF LINE SYSTEM DATA MEMORY PARTIAL CLEAR FUNCTION: This command is used to clear the data for specific features. PRECAUTION: This command can only be used in off-line mode. ASSIGNMENT PROCEDURE: CLEAR DESIGNATION + DE (2/3 digits) DATA TABLE: CLEAR DESIGNATION SYSTEM DATA TO BE CLEARED...
Page 62: Setting Of System Clock/Reading Out Of Daylight Saving Time
CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK/READING OUT OF DAYLIGHT SAVING TIME FUNCTION: This command is used to assign system clock data (year, date and time). And this command is used to read out of the daylight saving time. PRECAUTION: The system clock starts when is pressed.
Page 63 CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK/READING OUT OF DAYLIGHT SAVING TIME DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Setting of Calendar Year YYYY Calendar Year YYYY: Year (2011-2099) 2000 2000 Setting of Date (Month, Day, Day of Week) MMDDWW Date MM: Month (01-12)
Page 64 CM02 COMMAND CODE TITLE: SETTING OF SYSTEM CLOCK/READING OUT OF DAYLIGHT SAVING TIME : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Time difference between the System Clock XXXXX Time Zone (See the table below) and UTC NONE No Time Zone [8300R7] Time Zone data clear Time difference between the...
Page 65: Log In/Log Out Of Password Mode
CM03 COMMAND CODE TITLE: LOG IN/LOG OUT OF PASSWORD MODE FUNCTION: This command is used to enter a password which allows the authorized personnel to access commands in accordance with preassigned authorization levels. PRECAUTION: The password for each level is set by CME9. The accessible commands for each level is set by CME7.
Page 66: [Cm04] Setting Of System Services
CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES FUNCTION: This command is used to assign the setting of System Services, the setting of Language Indicated Num- ber, the 32-Party Conference with Password Protection, the Service Activation Dial for mobile phone in Mobility Access, the A-law/µ-law setting for each Unit, the SMDR data output and the System Infor- mation for Maintenance Report of PCPro.
Page 67 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES DATA TABLE: : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Display language for Mul- Japanese Services (a) tiline Terminal/ English DESKCON LCD French (System Base) (Canadian French) Spanish...
Page 68 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Default setting pattern for Default setting is not CM10 Services (a) Multiline Terminal provided (System Base) Fixed pattern 2 Fixed pattern and Fixed pattern 3...
Page 69 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Kind of Tone for TDM Japan CM67 Y=13 Services (a) (System-basis) North America Australia A-law countries Hong Kong Malaysia Singapore...
Page 70 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Single Line Telephone CM08>138 Services (a) ringing signal for Sta- 2 seconds ON-4 seconds CM35 tion-to-Station connec- Y=033 tion...
Page 71 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Single Line Telephone CM08>138 Services (a) ringing signal from a 2 seconds ON-4 seconds CM35 trunk Y=033 1 second ON-2 seconds OFF...
Page 72 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Special ringing signal CM08>179 Services (a) for Single Line Tele- 2 seconds ON-4 seconds CM35 phone ring Y=033 1 second ON-2 seconds OFF...
Page 73 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 00 Setting of System Ringing signal for CM04 Services (a) 2 seconds ON-4 seconds Y=00>05 [8300R7] 1 second ON-2 seconds OFF 0.5 seconds ON-0.5 seconds 0.25 seconds ON-0.25 seconds OFF...
Page 74 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 01 Setting of System Connection port for MCI RS1 on CPU Services (b) [8300R1] RS2 on CPU No data Available [8300R2 or later] Not available...
Page 75 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 01 Setting of System Control method for Hotel PMS, PMS with Hotel/ Services (b) Feature Motel Front Desk Instrument, DSS Con- sole Hotel/Motel Front Desk Instrument, DSS Con-...
Page 76 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 01 Setting of System Maximum number of DSP Maximum number of Services (b) resource used by Mobility DSP resource Access [8300R6] NONE...
Page 77 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 04 32-Party conference Conference group number With password protec- CM13 Y=73 with password protec- tion tion NONE Without password pro- [8300R5] tection NOTE:...
Page 78 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Unit No. 01-50 Destination to receive the Slot No. synchronous signal for DTI/PRT/CCT (First pri- ority) NONE No data BLADE RESET NOTE 1: Assign this data when the system is a slave office and receives the clock syn-...
Page 79 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 60 Destination of SMDR Station to station call Available terminal (RS Port 1/2) to Outgoing trunk call Not available send a call information Abandoned outgoing trunk (SRAM)
Page 80 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 62 Destination of PMS to Outgoing trunk call Available send a call information Not available (SRAM) Clear the destination of Clear [8300R3] PMS to send a call infor-...
Page 81 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 70 System Information for System Name XX..XX Character Maintenance Report of Customer Info. (Company (Maximum 64 digits: 32 characters) PCPro Name) [8300R5]...
Page 82 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES Fixed pattern and Programmable pattern CM04 Y=00>02 is the command which sets the system data such as CM90 and CM93 automati- cally for Multiline Terminals. Therefore, Multiline Terminals can be used as Multiline Terminal stations only by the setting of CM10.
Page 83 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES • Fixed pattern 2 (CM04 Y=00>02: 01) 2ND DATA Y No. 1ST DATA REMARKS My Line number B Mode Key No. 00 NONE No data Key No. 01 My Line number Key No. 02-32 NONE No data Key No.
Page 84 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES • Fixed pattern 3 (CM04 Y=00>02: 02) 2ND DATA Y No. 1ST DATA REMARKS Key No. 00-15 NONE No data Key No. 16 My Line number Key No. 17-32 NONE No data Key No.
Page 85 CM04 COMMAND CODE TITLE: SETTING OF SYSTEM SERVICES • Programmable pattern 1 (CM04 Y=00>02: 03) 2ND DATA Y No. 1ST DATA REMARKS NOTE Key No. 00-32 Second data of CM90 Y=10>00-32 Key No. 90-99 Second data of CM90 NOTE Y=10>90-99 Key No.
Page 86: [Cm05] Blade Type, Trunk Blade Number, Highway Channel For Isdn Data Communication
CM05 COMMAND CODE TITLE: BLADE TYPE, TRUNK BLADE NUMBER, HIGHWAY CHANNEL FOR ISDN DATA COMMUNICATION FUNCTION: This command is used to designate the type of blade installed. PRECAUTION: None ASSIGNMENT PROCEDURE: UNIT NUMBER UNIT NUMBER DATA ST + + DE SLOT NUMBER LINE/TRUNK CHASSIS NUMBER (2-3 digits)
Page 87 CM05 COMMAND CODE TITLE: BLADE TYPE, TRUNK BLADE NUMBER, HIGHWAY CHANNEL FOR ISDN DATA COMMUNICATION 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Blade Type XX ZZ XX : Unit No. (01-50) Direct Inward Dialing Trunk Blade ZZ : Slot No.
Page 88 CM05 COMMAND CODE TITLE: BLADE TYPE, TRUNK BLADE NUMBER, HIGHWAY CHANNEL FOR ISDN DATA COMMUNICATION : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Blade Type XX ZZ XX : Unit No. (01-50) ZT Interface Blade (CD-4CSIB/ ZZ : Slot No.
Page 89: [Cm08] Basic Services
CM08 COMMAND CODE TITLE: BASIC SERVICES FUNCTION: This command is used to assign basic features on a system wide basis. PRECAUTION: After setting 1st data 335, 391, 420, 592, 909, system reset is required. ASSIGNMENT PROCEDURE: BASIC SERVICE DATA (0/1) + 08 + FEATURE (1 digit)
Page 90 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When a dial-in incoming call from a tie line or DID line is Restricted (ROT connection) addressed to vacant levels or unassigned stations, the call is Predetermined station, DESKCON or routed to a predetermined station, Attendant Console or Voice Voice Response System assigned by Response System...
Page 91 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA If the * button on a DTMF telephone is pressed while hearing Effective busy tone, it is regarded as a Switch Hook Flash Ineffective If the # button on a DTMF telephone is pressed while hearing Effective busy tone, it is regarded as a Switch Hook Flash Ineffective...
Page 92 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Type of PS/Standard SIP station No-Answer timer As per CM41 Y=0>86 As per CM41 Y=0>01 Home PBX Numbering Plan for WCS Roaming Closed Numbering System [For PCS] [8300R2] Open Numbering System Loop on control after dialing for tandem connection, when the Loop on is not provided (Loop on is...
Page 93 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 101-199 : Default BASIC SERVICE SETTING DATA When CM08>102: 0 for Single Line Telephone The call with STA-B is disconnected, (Related command: CM35 Y=148) and STA-A returns to STA-C Three Party Conference When the station (STA-A), after holding the other station (STA- As per CM08>101 C), has made a switch hook flash while talking with another sta-...
Page 94 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA A station user is allowed to break into a call between a C.O. line Restricted party and another station by Executive Right of Way (Executive Allowed Override) Answer Key rings on TAS and Pooled Line To provide Not provided CM90 Y=00: F40XX...
Page 95 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Timing of Call Forwarding-No Answer for trunk incoming call As per timing for internal call or an assisted call (As per CM41 Y=0>15/CM41 Y=0>101/CME6 Y=08) As per timing for trunk incoming call (As per CM41 Y=0>01/CM41 Y=0>100/CME6 Y=07) Exclusive Hold on Multiline Terminal...
Page 96 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Multiline Terminal ringing signal for Station-to-Station connec- External Ringing tion Internal Ringing Multiline Terminal ringing signal for calls from station through External Ringing CCIS Internal Ringing Multiline Terminal ringing signal for calls from C.O./Tie Line Internal Ringing through CCIS External Ringing...
Page 97 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Transferred C.O. call to a busy station is automatically Available Camped-on when transferring station goes on-hook Not available (Recall transferring station) When a station transfers a C.O. call to a busy station, and per- The station hears Special Dial Tone forms a switch hook flash and use of Camp-On access code is...
Page 98 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Dialing of a Single Digit Feature Access Code while the calling Available station hears RBT, or performs a Voice Call Not available The table below shows the available features and its access codes for Single Digit Feature Access Code, while the calling station hears RBT.
Page 99 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Step Call for an incoming call from a Tie Line Not available Available Replay timer for Attendant Delay Announcement Replay at an interval [8300R2] CM41 Y=0>47 Replay only once When the Multiline Terminal station dials “#”...
Page 100 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Ringing cadence on Automated Attendant call, DID call and Special Ringing for Multiline Termi- DISA call CM08>397 [Other than North America] As per CM04 Y=00>06 for Single Line Telephone As per CM35 Y=033 or CM76 Y=22 Ringing cadence on Automated Attendant call, DID call and Special Ringing for Multiline Termi-...
Page 101 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 200-294 : Default BASIC SERVICE SETTING DATA Wake-up time printout on Hotel printer and the report is sent to Available PMS, when setting wake-up time from guest station Not available Do Not Disturb records print on Hotel printer and the report is Available sent to PMS, when setting Do Not Disturb from guest station Not available...
Page 102 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Dialing of a Single Digit Feature Access Code, while the calling Available station hears busy tone Not available To activate Single Digit Feature Access Code, set CM08>050, 051, 069, 148 and 543 to “1”. If the * button on a DTMF telephone is pressed while hearing busy tone, it is Ineffective regarded as a Switch Hook Flash...
Page 103 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When a caller encounters all ACD/UCD stations busy Busy Tone is to be sent out Caller is placed into queuing mode Method to cancel Call Forwarding-All Calls/-Busy Line/-No Feature access code + Feature key Answer Feature access code + “*”...
Page 104 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA To complete the operation for setting Call Forwarding-All Setting when the station goes on Calls-Outside/Busy Line-Outside/No Answer-Outside hook/when receiving Service Set Tone (PBR time out) Setting when receiving Service Set Tone (PBR time out) Whether the transferred C.O.
Page 105 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Dial Intercom to station set for Do Not Disturb Restricted (ROT connection) Allowed Operation of Station Hunting for a station with Do Not Disturb Station Hunting set (for DID/Tie Line/Station call) Do Not Disturb (ROT connection) Operation of Call Forwarding-Busy Line for a station with Do Call Forwarding-Busy Line...
Page 106 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Ring transfer for Call Transfer-All Calls to a trunk when a sta- Available tion holds another station/trunk Not available Whether the Hold key of the Multiline Terminal is used as the Call Park-Tenant Set key Call Park-Tenant Set key for an internal or external call Hold key...
Page 107 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Call termination to My Line while the station user makes a call Restricted with a Sub line or trunk line on Multiline Terminal NOTE 1 Allowed Busy indication on BLF of large type DESKCON, DSS Con- Station base sole or Multiline Terminal by station base or extension base Extension base...
Page 108 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 301-398 : Default BASIC SERVICE SETTING DATA When system is reseted Multiline Terminal MIC lamp ON Multiline Terminal MIC lamp OFF Display last calling station number 6 seconds Until next call Display calling station number when a calling station abandons Not available a call before the call is answered Available...
Page 109 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA When a call is transferred by Remote Access to System (DISA) Disconnect call to predetermined station and time-out occurs, the call is contin- Continue call ued or dropped CM30 Y=30 CM41 Y=0>39 Buzzer sound when terminating incoming call to attendant that Not provided...
Page 110 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Call Forwarding Override-CCIS Not available (BT connection) Available Alternative Routing when outgoing trunks of tandem office are Available all busy/Alternate Routing for multiple SIP Not available When forwarded call is terminated to VMS via CCIS, whether To provide Message Waiting from VMS is provided for the called station Not provided...
Page 111 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Multiline Terminal tone ringer selection By pressing Feature key and dialing 3 NOTE 1: Set “0” (Available) by CM08>262 to allow the ring NOTE 1 test tone to be heard when using the “Feature + 3” As per CM15 Y=083, 084, 093, NOTE 2 operation.
Page 112 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Multiline Terminal ringing signal patterns for an internal/exter- Depends on the combination of nal call and special ringing CM08>392 and 396 [Other than North America/Australia] (See the following table) Depends on the data set by CM08>392 and 396 UNIT: seconds...
Page 113 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Provide PAD for Multiline Terminal at all times To provide NOTE: For Europe, be sure to set the data to 0. Not provided Multiline Terminal connection PAD With PAD [For EU] Without PAD NOTE 1:...
Page 114 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 400-489 : Default BASIC SERVICE SETTING DATA Send Calling Party Subaddress to ISDN network To send Not sent Terminating system for Called Party Subaddress Station call Terminating system assigned by CM30 Y=02/03/40/41 Advice of Charge (AOC) display on Multiline Terminal when Flashing display the charge has been summed over $9999.99/€...
Page 115 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Charging to the transferring station or transfer destination sta- Charging to transferring station tion Charging to transfer destination sta- tion Shown below are stations to which call is to be charged in the case of various transfer patterns. STA: station DESKCON: Desk Console Transfer Pattern...
Page 116 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Forced release when called ISDN Telephone does not answer Not available for 3 minutes Available ISDN CPN (Calling Party Number) when making a call from CPN entered in ISDN Telephone ISDN Telephone CPN assigned by CM12 Y=12/13 Recall display on Attendant Console...
Page 117 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Send ANI/Caller ID/CPN to SMDR terminal To send Not sent OAI TSAPI Same as 2400 IPX system (recom- SCF facility mended setting) SMFN Off-Hook indication sent SCF error code type SCF error Detail SCF error Kind Method of readout the traffic information...
Page 118 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Select the Backward signal for ANI signal on DID MFC call Backward GC [8300R5] [Mexico Only] Backward GA NOTE: Both CM08>477 and 487 should be set the same data. Type of Single Data Message Frame Format Without Time Parameter With Time Parameter...
Page 119 Protected Login Mode for All IP Sta- tions As per CM15 Y=480 Whether the system encodes the station number when IP Sta- To encode (NEC Original method) tions login to the network Not encoded Whether the system encodes the password when IP Stations...
Page 120 User Mo- bility feature. Encoding method for the password NOTE: Effective when CM08>515 is set to 1. NEC Original method Whether the system sends SPDT when entering the name/num- Not sent ber for Dial by Name To send...
Page 121 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Type of Camp-On from DESKCON Semi-Automatic Camp-On [8300R2] Automatic Camp-On Whether the step call is to be restricted or not Restricted Allow Selection of the Guest information displayed on an administra- Display PMS information A/B tive station (Multiline Terminal/Attendant Console) for 8 char- Display VIP/language...
Page 122 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Action of monitoring station after the hold/hooking key is Keep monitoring pressed in the monitored station or the monitored station Stop monitoring becomes idle Information to display on the middle line of the Multiline Ter- Forwarding station name minal/DESKCON LCD when forwarding a trunk call to the Caller ID...
Page 123 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Number display on the called PS when calling from Sub Line My Line Number [8300R3.5] As per CM08>502 NOTE: The number displayed on the called PS is as follows when this command is set to “1”. - My Line Number is displayed when CM08>502 is set to “0”.
Page 124 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Call termination to My Line while the station user makes a call To activate the service (Call Forward- with a Sub line or a trunk line on a Multiline Terminal ing/Station Hunting) that set an incoming call As per CM08>268 (the calling station...
Page 125 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 600-685 : Default BASIC SERVICE SETTING DATA Selection of trunk route seized for Call Forwarding-All Calls/ By calling party’s tenant/terminating Busy Line/No Answer-Outside, Split Call Forwarding-All trunk’s tenant Calls/Busy Line/No Answer-Outside By Call Forwarding setting station’s tenant Reset of Queue Limit counter for TAS per tenant Not provided...
Page 126 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Trunk access code display when a call terminates via ETSI Available ISDN Not available [For EU] ETSI ISDN Overlap Sending To provide [For EU] Not provided BLADE RESET Ringing cadence on SIP trunk DID call assigned by CM76 To provide Y=22, 23/CM35 Y=033, 034...
Page 127 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 702-732 : Default BASIC SERVICE SETTING DATA Ringing signal/Live Record Start signal which includes caller To send information (such as station number and kind of calling party) Not sent is sent to VMS NOTE: Set the second data to “0”...
Page 128 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Whether to link with a VMS soft key feature (CM13 Y=37)/ Only as per CM13 Y=37/CM08>702 expand AAINFO (CM08>702) As per CM13 Y=37/CM08>702 and expansion information sent to VMS Station number sent to VMS when accessing VMS from a sub- Subline station number line assigned on Multiline Terminal...
Page 129 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 801-898 : Default BASIC SERVICE SETTING DATA Send Office Number to Center Office for Centralized Billing- To send CCIS Not sent NOTE: When the network adopts Open Numbering Plan, set the office number by CMA7 Y=06. When the network adopts Closed Numbering Plan, set the office number by CMA7 Y=07.
Page 130 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA OAI SMFN STS (status) when the forwarded call with Call SMFN STS=4/5/6 Forwarding-All Calls/Busy Line/No Answer is terminated to a SMFN STS=0 station via CCIS (SMFN FID=1) OAI SMFN STS (status) when a station answers via CCIS the SMFN STS=5/6/7 forwarded call with Call Forwarding-All Calls/Busy Line/No SMFN STS=0...
Page 131 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Kind of Center Office for Centralized Billing-CCIS SV8300 2400 IPX NOTE 1: Set this data to the Local Office of the Centralized Billing-CCIS. This data setting is not required for Center Office.
Page 132 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Setting CAMP ON to the destination when Call Forwarding-All To set Calls is set by SCF FID=19 Not set Send OAI SMFN when setting CAMP ON of OAI SMFN To send FID=6 STS (status)=3 for the Call Hold status Not sent...
Page 133 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Printing way of Automatic Wake Up for an individual station To print process and result execution To print only result NOTE: When the second data is set to 0, the record of RING ON/STATION BUSY/CONNECTION BLOCK is also printed with ANSWER/NO ANSWER.
Page 134 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA Setting of number of sending digits for printer Printer for 80 digits [8300R2] Printer for 20 digits Whether to provide ACC/AUTH for Station Individual Call To provide Record Print/Immediate Printout Call Record Not provided [8300R2] Setting of decimals for Call charge...
Page 135 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 909-921 : Default BASIC SERVICE SETTING DATA Allow Built-in modem/Speech synthesis service/Voice Allow Response System (VRS) used by CF memory Restricted RESET NOTE: Voice Response System (VRS) used by CF memory is effective for 8300R3 software or later. Layout the key on CAT mode Old layout (8300R2 or before) [8300R3]...
Page 136 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1000-1031 : Default BASIC SERVICE SETTING DATA 1000 Operation of Recall key when a station receives SPDT after Recall key is not available hooking Return to the original call [8300R3] 1001 Transfer a trunk line placed in Consultation Hold by Recall Key Available (Hold Transfer) (Hold Transfer) on Trunk-Direct Appearance Not available (Recall)
Page 137 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA 1012 Display Caller ID to my line same as sub line when Automatic Not available Caller ID to sub line by CM15 Y=224/225 is available Available [8300R5] 1014 Select the function to override by preset Station dialing/Pro- Do Not Disturb (DND), Call For- grammable key on a Multiline terminal warding-All Calls...
Page 138 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA 1030 Whether to transmit the caller ID of the call originator when an To transmit Attendant Console holds the trunk incoming call and transfer it Not transmitted to the trunk [8300R7] NOTE 1: This data is effective when CM65 Y=306 is set to 0 or CMBA Y=44 is set to 01/15.
Page 139 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1200-1210 : Default BASIC SERVICE SETTING DATA 1200 Send ANI signal to PSTN on DOD MFC call To send [8300R3.5] Not sent NOTE: For Brazil, set this command to “0”. 1201 Sender Tone sending on DOD MFC call Not sent [8300R3.5] To send...
Page 140 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1400-1404 : Default BASIC SERVICE SETTING DATA 1400 Speech Synthesis language feature for Do Not Disturb/Return Allow Message Schedule Display Restricted [8300R3] 1401 Speech Synthesis Service language feature for Room Cutoff Allow [8300R3] Restricted 1402 Edit IEI=7BH (Call appearance) on SETUP message...
Page 141 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1600-1603 : Default BASIC SERVICE SETTING DATA 1600 Check on tenant number in term inf of OAI Available [8300R4] Not available 1601 Selection of SMFN3 of a trunk when abandons an outgoing call SMFN3 STS=1 via trunk SMFN3 STS=0...
Page 142 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1701-1702 : Default BASIC SERVICE SETTING DATA 1701 Wake Up Call Information Printout of All Guest Station Infor- Available mation by Printer for 20 digits when Wake Up Call is ineffec- Not available tive [8300R3] 1702 Printout of Administrative Station Information (assigned by...
Page 143 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1800-1872 : Default BASIC SERVICE SETTING DATA 1800 Printout by Direct Data Entry Available [8300R3] Not available 1801 Printing format of Direct Data Entry Format2 [8300R3] Format1 1817 Whether to send Check Out Outgoing Call Report (FTC=16, Not sent FC=C) to PMS when guest station is engaged in an outgoing To send...
Page 144 CM08 COMMAND CODE TITLE: BASIC SERVICES : Default BASIC SERVICE SETTING DATA 1872 Trunk Call Restriction setting from Front Desk Instrument Available [8300R7] Not available NOTE 1: When operated restriction of an outgoing call for a station in Check in status from Front Desk Instru- ment while CM08>1872: 0, the trunk restriction class is changed from the class assigned by CM12 Y=01 to the class assigned by CM15 Y=404.
Page 145 CM08 COMMAND CODE TITLE: BASIC SERVICES BASIC SERVICE: 1926 : Default BASIC SERVICE SETTING DATA 1926 Displaying the received digits of DTMF Caller ID (For test) To provide [8300R5] Not provided NOTE: The received digits (maximum 16 digits) is displayed on LCD of Multiline Terminal directly. 3-89 NWA-033623-001 Rev.8.1 91ch3001.fm...
Page 146: [Cm0B] Lan Data Assignment
CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT FUNCTION: This command is used to assign the LAN data for Maintenance port of CPU blade and VOIP port of VoIPDB. Set each port by the operational pattern to be used. For details, refer to PRECAUTION (1) on this page.
Page 147 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT When setting the IP address for Maintenance Port (Y=0XX) and VOIP Port (Y=1XX), set the segments for each using port respectively. There are the following conditions when setting the default gateway address by this command. •...
Page 148 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 0BYYY + (2-3 digits) (1-128 digits) DATA TABLE: Y=000 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 000 Unit number setting –...
Page 149 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT Y=0XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port IP Address for the sys- XXX.XX IP Address XX: Unit No. (01-50) ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= RESET 0.0.0.1-255.255.255.254...
Page 150 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port OAI Port number OAI port number 1024 XX: Unit No. (01-50) OAI port number 1025 OAI port number 1039 RESET OAI port number 60030...
Page 151 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Port selection for OAI Maintenance port NOTE 1, NOTE 2 XX: Unit No. (01-50) VOIP port RESET Port selection for SMDR NOTE 1, NOTE 2...
Page 152 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Community name XX...X Character NOTE (Maximum 25 characters) XX: Unit No. (01-50) No data NONE RESET System information XX...X...
Page 153 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port Community name for the XX...X Character destination of trap XX: Unit No. (01-50) (Maximum 25 characters) (Fourth place) NONE No data...
Page 154 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port IP Address for the SNMP XXX.XX IP Address for the SNMP XX: Unit No. (01-50) manager ...X manager...
Page 155 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port IP Address for the trap XXX.XX IP Address for the trap XX: Unit No. (01-50) source ...X source...
Page 156 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 0XX 0 : Maintenance Port SIP trunk feature of Allowed CMA7 Y=83 XX: Unit No. (01-50) Secondary unit Restricted [8300R6] RESET NOTE 1: Only Unit No.
Page 157 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT Y=1XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port IP Address for the sys- XXX.XX IP Address XX: Unit No. (01-50) ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= RESET 0.0.0.1-255.255.255.254...
Page 158 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Location number for sta- Location number 00 CM12 Y=39, XX: Unit No. (01-50) tions/VoIPDB accommo- Location number 63 dated in the Unit Location number 00...
Page 159 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port UDP Port for IP Multi- 01024 TCP/UDP/RTP Port num- XX: Unit No. (01-50) line Terminal voice con- 65534 trol NONE...
Page 160 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port UDP Port for SIP control 01024 TCP/UDP/RTP Port num- XX: Unit No. (01-50) packet 65534 RESET NONE 1st data=36: 5060...
Page 161 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port VLAN function To provide XX: Unit No. (01-50) Not provided RESET Priority of VLAN ID Priority 0 Priority 1 RESET...
Page 162 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Primary IP Address for XXX.XX IP Address for DNS server XX: Unit No. (01-50) DNS server ...X (Maximum 15 digits) XXX.XXX.XXX.XXX=...
Page 163 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Valid duration of the first 0001 1 minute CM0B XX: Unit No. (01-50) query to a DNS server (1 minute increments) Y=1XX>60, 1440...
Page 164 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Start time for the auto- Not execute the automatic XX: Unit No. (01-50) matic changeover to sur- changeover to survival vival mode from normal mode...
Page 165 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Start time for the auto- Not execute the automatic XX: Unit No. (01-50) matic changeover to nor- changeover to normal mal mode from survival mode...
Page 166 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Start time to notify the Not notify the link down XX: Unit No. (01-50) link down to the Multi- 0-6 seconds line Terminal after the (Unit No.
Page 167 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port Provide the system with To provide CM0B XX: Unit No. (01-50) the automatic change- Not provided Y=1XX>81 over to normal mode from survival mode after...
Page 168 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port UDP Port for standard 01024 UDP port number XX: Unit No. (01-50) SIP control packet between Units 65534 [8300R7]...
Page 169 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 1XX 1 : VOIP Port SNTP query Now executing XX: Unit No. (01-50) (Status display) Not executed (failed in the (Only Display) previous time) [8300R7]...
Page 170 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT Y=2XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port IP Address 1 (RTP) for XXX.XX IP Address XX: Unit No. (01-50) VoIPDB ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= RESET...
Page 171 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port IP Address 2 (RTP) for XXX.XX IP Address XX: Unit No. (01-50) VoIPDB ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= RESET 0.0.0.1-255.255.255.254...
Page 172 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port IP Address 6 (RTP) for XXX.XX IP Address XX: Unit No. (01-50) VoIPDB ...X (Maximum 15 digits) XXX.XXX.XXX.XXX= RESET 0.0.0.1-255.255.255.254...
Page 173 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port RTP Base Port for Voice 01024 RTP Port number CMA7 Y=46 XX: Unit No. (01-50) Packet transmitting/ CMBA receiving...
Page 174 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port Tone Disabler for the Available XX: Unit No. (01-50) FAX communication on Not available the SIP trunk NOTE 1: This data is not effective for Secondary Unit (Unit No.
Page 175 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port CNG ceiling (clip) level -30 dBm0 XX: Unit No. (01-50) [8300R3] -55 dBm0 NOTE 1: Do not change this data when the system is operated normally.
Page 176 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port Maximum NLP Action 0001 -42.46 dBm0 CM0B XX: Unit No. (01-50) Threshold 0002 -39.45 dBm0 Y=300>XX3 [8300R3] 0004...
Page 177 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port HLC Mode Disable HLC CM0B XX: Unit No. (01-50) [8300R3] Enable HLC Y=300>XX4 Set HLC CM0B Threshold Y=2XX>147...
Page 178 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 2XX 2 : VOIP Port Payload type of Out- Payload type XX: Unit No. (01-50) band DTMF (RFC2833) [8300R7] NONE NOTE: Assign this data when Payload type of Out-band DTMF (RFC2833) is changed between VoIPDB and standard SIP station.
Page 179 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT Y=300 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 300 Characteristic level XX0 XX: Characteristic level Disable CM0B data (00-09) Enable Y=2XX>110 [8300R3] 0 : NLP NONE As per CM0B Y=2XX> NOTE: Do not change this data when the system is operated normally.
Page 180 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 300 Characteristic level XX2 XX: Characteristic level 0000 NLP will not disengage CM0B data (00-09) 0001 -90.62 dBm0 Y=2XX>142 [8300R3] 2 : Minimum NLP 0002 -87.61 dBm0...
Page 181 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 300 Characteristic level XX3 XX: Characteristic level 0001 -42.46 dBm0 CM0B data (00-09) 0002 -39.45 dBm0 Y=2XX>143 [8300R3] 3 : Maximum NLP 0004 -36.44 dBm0 Action Threshold...
Page 182 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 300 Characteristic level XX5 XX: Characteristic level 0006 +3 dBm0 CM0B data (00-09) Y=2XX>147 [8300R3] 5 : HLC Threshold 0000 0 dBm0 CM0B FFFF...
Page 183 CM0B COMMAND CODE TITLE: LAN DATA ASSIGNMENT Y=3XX : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING 3XX 3: Characteristic level VoIPDB channel number Characteristic level CM15 per channel Y=483 XX: 01-50 (Unit No.) CM35 [8300R3] NONE No data Y=193...
Page 184: [Cm0C] Updating Of Ip Station Firmware/Remote System Upgrade
CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE FUNCTION: This command is used to specify the update information of IP Station firmware and Remote System Up- grade. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 0CYY + (1-8 digits) (1-12 digits) DATA TABLE:...
Page 185 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Update information Firmware file ver- AABBCCDD AA : Integral No. of file version Profile No. sion for update (For SIP Multi- (00-99) line Terminal)
Page 186 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Information of XX01 Port number for 00001 TCP Port No. for the FTP server Remote System FTP server Upgrade 65534 XX: Unit No.
Page 187 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Information of XX06 File type CPU program file Remote System Clear Upgrade XX: Unit No. NONE No data (01-50) Continued on next page 3-131...
Page 188 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Start updating IP IP Station No. Start updating Station firmware XXXXXXXX NOTE: After setting the first data and second data, PCPro/CAT displays the status of the IP Station. The table below shows the contents of the display and its meaning.
Page 189 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX00 Execute CPU pro- Start to download Upgrade gram download Now downloading Not executed XX: Unit No. YYYY MM Download time (01-50)
Page 190 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX01 Changeover YYYY MM YYYY: Year (2011-2099) Upgrade (changeback) DD HH mm : Month (01-12) time : Date (01-31) : Hour (00-23) XX: Unit No.
Page 191 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Remote System XX05 The latest result XX YY ZZ XX: File type Upgrade of CPU program YYYYMMDD 00: CPU program file download HH mm YY: Executed operation...
Page 192 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING System Upgrade 0100 Execute CPU pro- Start to download (Stand by CPU) gram download Now downloading [8300R4] Not executed YYYY MM Download time DD HH mm...
Page 193 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING System Upgrade 0101 Changeover YYYY MM YYYY: Year (2011-2099) (Stand by CPU) (changeback) DD HH mm : Month (01-12) [8300R4] time : Date (01-31)
Page 194 CM0C COMMAND CODE TITLE: UPDATING OF IP STATION FIRMWARE/REMOTE SYSTEM UPGRADE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING System Upgrade 0105 The latest result XX YY ZZ XX: File type (Stand by CPU) of CPU program YYYYMMDD 00: CPU program file [8300R4]...
Page 195: [Cm10] Station Number, Trunk Number, Blade Number
CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER FUNCTION: This command is used to assign station numbers, trunk numbers, and blade numbers to Physical Port No. (Unit No. + Slot No. + Circuit No.)/Virtual Port No. PRECAUTION: When deleting a station number (Single Line or Multiline Terminal), be sure to delete Call Pickup data (CM16), ACD/UCD Group data (CM17) and Station Hunting Group data (CM18) in advance.
Page 196 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TDM terminal/Trunk XXYYZZ Physical Port num- D000 Trunk number (C.O./Tie CM30 registration Line, Paging, Radio Paging) CM35 D511 NOTE 1: “About Unit XX: Unit number This data requires...
Page 197 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TDM terminal/Trunk XXYYZZ Physical Port num- EC00 Add-on Module number CM90 registration NOTE: The same number CM98 “About Unit XX: Unit number EC31 (the last two digits...
Page 198 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TDM terminal/Trunk XXYYZZ Physical Port num- Digital Multiline Terminal CM90 registration station number “About Unit XX: Unit number X-XXXXXXXX represents number, Slot number (01-50)
Page 199 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING IP terminal registra- 0000 Virtual Port num- EC00 Add-on Module number CM90 tion ber (for IP terminal) NOTE: The same number CM98 1535 EC31...
Page 200 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING IP terminal registra- 0000 Virtual Port num- NONE No data tion ber (for IP terminal) 1535 IPT (P2P CCIS) regis- Virtual Port num- D000 Trunk No.
Page 201 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING SIP trunk registration 01XXX Virtual Port num- D000 Trunk No. ber (for SIP trunk) RESET D511 XXX: 000 (Port No. NONE No data for control...
Page 202 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING PS/Standard SIP sta- Virtual Port number PS/Standard SIP station No. tion registration XXX-XXXX X: 0-9, A (*), B (#) XXXX : 000-511 XXXX...
Page 203 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER About Unit number, Slot number and Circuit number The following describes the Unit number, Slot number and Circuit number that are set by CM05 and CM10. Unit Number The Unit means the Main Unit that consists of CPU chassis (1U) and Line/Trunk chassis (2U). Up to a maximum of 50 Units can be installed, and each Unit is managed by the Unit number.
Page 204 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Outline of the Unit No. Unit No. 01 Unit No. 02 Unit No. 05 Unit No. 50 Unit No. 03 Unit No. 04 Remote Unit for Remote UNIT over IP Stand-alone system/ Main Unit for Remote UNIT over IP Continued on next page...
Page 205 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Slot number and Circuit number The Slot number is the number assigned to the slot which accommodates the blade in a Line/Trunk chassis. The Circuit number is the number assigned to the circuit which accommodates the blade in a Line/ Trunk chassis.
Page 206 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER Setting method of Port number/Station number in Dual port mode When using Analog Port Adapter and PGD(2)-U10 ADP in Dual port mode NOTE 1, the Circuit numbers (17-32) of the DLC blade slot which accommodate Digital Multiline terminal/PGD(2)- U10 ADP are used for the virtual station.
Page 207 CM10 COMMAND CODE TITLE: STATION NUMBER, TRUNK NUMBER, BLADE NUMBER NOTE 3: When a new virtual station is added, reassignment of highway channel (CMF7 Y=9) and blade reset (CME0 Y=3) are required for all DLC blade which is accommodated by Line/ Trunk chassis (2U) after office data setting.
Page 208 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER FUNCTION: This command is used to assign station numbers, Intercom numbers, Loop Line numbers and ICI/OPR Line numbers (for Multiline Terminal Attendant Position) to Virtual Lines assigned on Multiline Termi- nal. PRECAUTION: Virtual Line station numbers must be different from station numbers assigned by CM10. The Virtual Port No.
Page 209 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER ASSIGNMENT PROCEDURE: VIRTUAL VIRTUAL LINE INTERCOM + 11 + + EXE NUMBER NUMBER PORT NUMBER (4 digits) (1-8 digits) (4 digits) DATA TABLE: VIRTUAL RELATED VIRTUAL LINE NUMBER PORT No. COMMAND 0000-0999 Station number (1-8 digits) CM20 X: 0-9, A (*), B (#) CM90...
Page 210 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER : Default VIRTUAL RELATED VIRTUAL LINE NUMBER PORT No. COMMAND 0000-0999 B000 Dial Intercom number CM12 Y=03 CM56 Y=12 B900 BX YY CM90 B001 X : Intercom Code (0-9) YY : Dial Intercom Group number (00-24) B901 NOTE 3 B024...
Page 211 CM11 COMMAND CODE TITLE: VIRTUAL LINE NUMBER NOTE 1: Automatic Intercom numbers are assigned as shown below: AUTOMATIC AUTOMATIC AUTOMATIC INTERCOM INTERCOM INTERCOM GROUP No. (A) No. (B) A000 A100 A001 A101 A031 A131 NOTE 2: Manual Intercom numbers are assigned as shown below: MANUAL INTERCOM GROUP...
Page 212: [Cm12] Station Class-1
CM12 COMMAND CODE TITLE: STATION CLASS-1 FUNCTION: The features for each station are determined by assigning Station Class-1 to each station number. PRECAUTION: When assigning Station Class-1 to Multiline Terminal by this command, enter “X-XXXXXXXX (My Line number)” of FX-FXXXXXXXX, which is assigned by CM10 Y=00, as the first data.
Page 213 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) DT330/ LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 DT730 LINE07 LINE08 LINE09 LINE10 LINE11 LINE12 (12D)+ 16LK Same as CM12 Y=24: 7 (A mode) DT330/ LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 DT730...
Page 214 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) DT330/ LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 DT730 LINE07 LINE08 LINE09 LINE10 LINE11 LINE12 LINE07 LINE08 LINE09 LINE10 LINE11 LINE12 (24D)+ LINE13 LINE14 LINE15 LINE16 LINE17 LINE18...
Page 215 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) DT330/ LINE01 LINE05 LINE01 LINE05 DT730/ LINE02 LINE06 LINE02 LINE06 Front Front Page Page DT750 LINE03 LINE07 LINE03 LINE07 LINE04 LINE08 LINE04 LINE08 (8LD [DESI- LINE09 LINE13...
Page 216 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) DT710 LINE01 LINE05 (8LDE LINE02 LINE06 Same as CM12 Y=24: 7 (A mode) [DESI- LINE03 LINE07 less]) LINE04 LINE08 DT300 LINE01 LINE02 LINE03 LINE04 LINE05 LINE06 Series LINE07 LINE08 LINE09 LINE10 LINE11 LINE12 (DTL-...
Page 217 CM12 COMMAND CODE TITLE: STATION CLASS-1 CM12 Y=24: 7 (A mode) CM12 Y=24: 0 (B mode) term LINE01 LINE02 LINE03 LINE04 Series i LINE05 LINE06 LINE07 LINE08 (DTR- LINE09 LINE10 LINE11 LINE12 16D-1R)/ Same as CM12 Y=24: 7 (A mode) LINE13 LINE14 LINE15 LINE16 term (DTP-...
Page 218 CM12 COMMAND CODE TITLE: STATION CLASS-1 : To assign –: Not assigned STATION NUMBER 00 01 02 03 04 05 07 11 12 13 16 19 20 22 23 24 25          ...
Page 219 CM12 COMMAND CODE TITLE: STATION CLASS-1 : To assign –: Not assigned STATION NUMBER 26 29 30 31 32 33 34 35 36 37 38 39 43 44 45 46 47          ...
Page 220 CM12 COMMAND CODE TITLE: STATION CLASS-1 : To assign –: Not assigned STATION NUMBER 48 50 61 62 63 64 65 66 67 68 69 70 71 72 76 77 78        Single line station number –...
Page 221 CM12 COMMAND CODE TITLE: STATION CLASS-1 : To assign –: Not assigned STATION NUMBER 79 80 90 92 93 96 97 98   Single line station number – – – – – – (Assigned by CM10 Y=00)   Multiline Terminal My line –...
Page 222 CM12 COMMAND CODE TITLE: STATION CLASS-1 ASSIGNMENT PROCEDURE: AUTOMATIC/ LOOP ICI/OPR STATION No. MANUAL/ 12YY LINE No. LINE No. ST + (1-8 digits) DIAL INTERCOM No. (4 digits) (4 digits) (4 digits) DATA (1-12digits) DATA TABLE: : Default SETTING DATA RELATED COMMAND MEANING...
Page 223 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Telephone House Phone 0 CM51 Y=14 House Phone 1 House Phone 2 House Phone 3 FAX Call Station Group No. 0 CM51 Y=14 FAX Call Station Group No.
Page 224 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Accommodation of Single Accommodated CM10 line telephone/FAX call Not accommodated CM90 station to Multiline Termi- CM13 Y=08 ’ s Multiline, Accommo- dation of PS to Soft Phone’s Multiline Service Restriction Class C Service Restriction Class C (00-15)
Page 225 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk to be seized as D000 Trunk number CM35 Y=018 Private Line on per station CM35 Y=028 basis D511 CM15 Y=025 NONE No data NOTE: When assigning Private Line on a per station basis, Outgoing Trunk Queuing (Trunk Queuing- Outgoing) and Timed Queue features are not available.
Page 226 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Multiline Terminal B mode CM94 A mode NOTE 1: Refer to PRECAUTION (3) for the combination of Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 227 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Sending BLF message via To send CM50 Y=08>4 CCIS to Destination No.4 Not sent Sending BLF message via To send CM50 Y=08>5 CCIS to Destination No.5 Not sent Sending BLF message via To send...
Page 228 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Calling Party Number X-XXXX SIP subscriber number (Indial No.) CM12 Y=12 displayed on called side NONE No data Local Office Code Table SIP Local Office Code Table number 00 CM12 Y=13 SIP Local Office Code Table number 14 No data...
Page 229 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Display language for Mul- Japanese CM04 tiline Terminal LCD (Sta- English Y=00>00 tion Base) French (Canadian French) Spanish (Latin Spanish) Portuguese (Brazilian Portuguese) German Italian Netherlandish [8300R2] French (Europe)
Page 230 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING External Key group num- External Key Group No. 00 CM12 Y=65: 3 ber of PGD(2)-U10 ADP CM61 NOTE: Effective when the External Key Group No. 63 second data of CM12 Y=65 is set to “3”.
Page 231 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING DT300/700 series Display Second line is twofold font, First line is delete CM90 Y=00: Enhancement for Univer- Third line is twofold font, First line is delete F5030, F5031 sal Design NONE...
Page 232 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Registered IP Station MAC X..XXX MAC Address display Address display/clear (12 digits) MAC Address automatic registration in Fixed Con- nection Mode Clear NONE No data NOTE 1: If you clear the registered IP Station MAC Address while the system is operating, IP Station is reset even if it is connected.
Page 233 CM12 COMMAND CODE TITLE: STATION CLASS-1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Standard SIP station con- Not connected (Display only) nection status Connecting (Display only) [8300R3.5] NONE Other than Standard SIP station (Display only) Idle Return (Forced) NOTE 1: When a station during calling is set forced idle return by this data, the forced idle return is completed and the call is terminated.
Page 234: [Cm13] Station Class-2
CM13 COMMAND CODE TITLE: STATION CLASS-2 FUNCTION: The features for each station are to be designated by assigning Station Class-2 for each station number. PRECAUTION: When assigning Station Class-2 to a Multiline Terminal by this command, enter “X-XXXXXXXX (My Line number)” of FX-FXXXXXXXX, which is assigned by CM10 Y=00, as the first data.
Page 235 CM13 COMMAND CODE TITLE: STATION CLASS-2 : To assign –: Not assigned 34 35 37 39 40 41 45 46 49 51 52 54 55 56 57 58 59 60 61 63 64 66 67 68 69 STATION NUMBER – – –  – – –  –  – – – – – – – – – –  – – –  Single line station number (Assigned by CM10 Y=00)
Page 236 CM13 COMMAND CODE TITLE: STATION CLASS-2 DATA TABLE: : Default SETTING DATA MEANING DATA MEANING Do Not Disturb-System To provide Not provided Room Cutoff-System To provide Not provided Off-Hook Alarm To provide CM51 Y=12 Not provided Message Waiting/Stored Call Record To provide (for the station with MW lamp) Not provided NOTE:...
Page 237 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING BLF indication for Automatic Intercom To provide Not provided Secretary station (Boss Secretary Trans- Secretary station fer/Override) Ordinary station or Boss station Ordinary station or Front Desk Terminal/ Message Waiting Front Desk Terminal/Administra- Administrative station tive station...
Page 238 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Port mode of Analog Port Adapter/ Dual port mode PGD(2)-U10 ADP Single port mode BLADE RESET PRECAUTION (4) Designation of station connected to Dual Station connected to Dual port mode of Analog Port port mode of Analog Port Adapter/ Adapter/PGD(2)-U10 ADP PGD(2)-U10 ADP...
Page 239 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Kind of station in the hotel function Administrative station Guest station NOTE: Set the second data to “0”, when the station except Hotel Console and Guest station is used. Whether the PMS information for 8 char- Display information assigned by CM08>548 acters display in left-side on upper line of...
Page 240 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Storage of the call history (IC) when han- To store dling of unanswered a trunk call Not stored term Accommodation of D 70/PGD(2)-U10 To accommodate Not accommodated BLADE RESET NOTE 1: Set this data only for a Base Port of DLC blade.
Page 241 CM13 COMMAND CODE TITLE: STATION CLASS-2 : Default SETTING DATA MEANING DATA MEANING Provide Calling Number Display for the To provide My Line when an incoming call is termi- Not provided nated to the Sub Line of Multiline Termi- [8300R3.5] Calling Party Number sending to ISDN As per CM13 Y=71 when making an outgoing call from Sub...
Page 242: [Cm15] Service Restriction Class
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS FUNCTION: Restriction of each service is to be set for each service restriction class assigned to the stations. There are four kinds of Service Restriction Class A/B/C and Charging Station. The services to be restricted by these Service Restriction Classes are different.
Page 243: [Cm15] Service Restriction Class A
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A DATA TABLE: Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 000 Call Forwarding-All Calls Restricted Allow 001 Call Hold 002 Outgoing Trunk Queuing 003 Call Back 005 Executive Right of Way (Executive Override) Calling side 006 System Speed Dialing...
Page 244 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 021 Automatic Wake Up set from guest or administrative station Restricted (Different wake up time is set to multiple stations) Allow 022 Trunk-to-Trunk Transfer 024 Message Waiting Lamp set/reset from station...
Page 245 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 041 Voice Message Waiting-System/Individual Restricted Set/Cancel/Retrieve Allow 042 Voice Message Waiting-System Recording 043 Call Waiting Set-Calling Side 044 Call Waiting Answer-Called Side 046 Call Back-Multiple Assignment 047 Message Reminder Setting Side...
Page 246 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 115 PS/Standard SIP station Call Forwarding-Not Available Restricted Allow 116 Voice Guide Restricted Validity of dial tone sending Allow 117 WCS Roaming Allow...
Page 247 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 129 WCS Number Sharing Main station and sub Sub station is controlled as same as main station, by Message station are controlled Waiting lamp control signal sent to main station Only main station is...
Page 248 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 135 Keep volume level changed by volume button on Multiline Allow Terminal, after the call is finished. Restricted 136 Calling Number/Calling Name Display for ISDN/T1-ANI/ Calling Number...
Page 249 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 205 Selection of Off Hook Ring Volume Off Hook Ring Volume 2 (As per CM42>75) Off Hook Ring Volume 1 (As per CM42>74) NOTE:...
Page 250 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 218 Call Forwarding-All Calls of Mobility Access call Restricted Allow 219 Call Forwarding-Busy Line/-No Answer for call forwarding Restricted in Mobility Access Mode Allow...
Page 251 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 228 32-Party Conference Connection by Call Transfer Restricted [8300R5] Allow NOTE: This data is effective for the station of Call Transfer operator from own office. The station of Conference participants from the different offices via CCIS/IP trunk (P2P CCIS) is allowed to participate in Confer- ence regardless of this data.
Page 252 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 401 Entry of Authorization Code/Forced Account Code after dial- Allow (Authorization ing an LCR access code and desired number Code) Allow (Forced Account Code)
Page 253 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 404 Trunk restriction class to be changed when the Restriction Unrestricted (RCA) Level=1, 6 (Room Cutoff Set) of the Restriction Control Non-Restricted 1 (FTC=15, FC=1) is set from the PMS (RCB)
Page 254 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS A Service Restriction Class A : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (A) 408 VRS Waiting Message Restricted [8300R7] Allow 409 Whether to transmit the caller ID of the call originator when To transmit an intermediate station holds the trunk incoming call and Not transmitted...
Page 255: [Cm15] Service Restriction Class B
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS B Service Restriction Class B : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) 053 TAS Service Restricted Allow 055 Individual Trunk Access from Station 056 Change of mode for CAT 059 Starting up OAI MSF from PB telephone/Multiline Terminal by using access code 060 Day Night Mode Change by Station Dialing...
Page 256 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS B Service Restriction Class B : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (B) 072 Automatic Hold Allow Restricted 073 Attendant Terminal ICI/OPE Key ICI/OPE Key CM15 Y=071 Regular station 075 Maid Status Restricted Allow 076 Collect Call Called Side...
Page 257: [Cm15] Service Restriction Class C
CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 081 One hit ringing for Call Forwarding-All Calls Restricted Allow 082 Ringing Line Pick up Allow Restricted Multiline Terminal Ringer Tone Pattern See below The ringer tone pattern is assigned by the combination of...
Page 258 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) Switch Hook Flash during internal call See below Result of a Switch Hook Flash during a station-to-station call is specified by the combination of CM15 Y=088, 089.
Page 259 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 093 Multiline Terminal Ringer Tone Pattern See below Multiline Terminal ringer tone pattern is assigned by the fol- lowing combination of CM15 Y=083, 084, and 093.
Page 260 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) Service for overflowed Off-Hook Alarm call See below Service for an Off-Hook Alarm call which encounters the ter- minating station busy is specified by the combination of data for CM15 Y=097, 098.
Page 261 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 199 Security Mode for DT700 Series Restricted Allow NOTE: When this data is changed while the system is operating, reboot the terminal (re-login to the PBX). 280 Automatic change of Display for Multiline Terminal (DESI- Allow less) incoming call...
Page 262 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 480 ID registration method for IP Station Protected Login Mode NOTE 1: Effective only when CM08>513 is set to 1. (Service Restriction NOTE 2: Set the second data to “7”...
Page 263 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 484 Priority for Call Forwarding-All Calls of Mobility Access call See below : Default PRIORITY 2ND DATA=0 2ND DATA=3 Restriction of Inter-tenant Connection Restriction of Inter-tenant Connection...
Page 264 CM15 COMMAND CODE TITLE: SERVICE RESTRICTION CLASS C Service Restriction Class C : Default SERVICE SETTING DATA REST. MEANING DATA MEANING CLASS (C) 485 Time that LCD backlight for DT300/DT700 Series Always off [8300R2] Always on 5 seconds 10 seconds 15 seconds 30 seconds 60 seconds...
Page 265: [Cm15] Charging Station Class
CM15 COMMAND CODE TITLE: CHARGING STATION CLASS Charging Station Class : Default CHARGING SETTING DATA STATION MEANING DATA MEANING CLASS 390 Send detail information of Immediate Printout Call Record for Allow the PMS Restricted 391 Accumulate the call charge Allow Restricted 393 The operation set by CM4B Y=00 is executed simultaneously Allow...
Page 266: [Cm16] Call Pickup Group/Group Diversion Group
CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP FUNCTION: This command is used to allocate stations to each Call Pickup group and Group Diversion group. PRECAUTION: The maximum number of stations which can be assigned to a Call Pickup group is 60. There is no limitation to the number of Call Pickup groups.
Page 267 CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP DATA TABLE: : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number Station number (A) Station number (B) in Call Pickup Group XXXXXXXX XXXXXXXX NONE No data When assigning station numbers to a Call Pickup group, only two station numbers can be assigned per operation.
Page 268 CM16 COMMAND CODE TITLE: CALL PICKUP GROUP/GROUP DIVERSION GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Pilot station in Call Station number in Call Pilot station Pickup group Pickup-Group Member station NOTE XXXXXXXX NOTE: Only one station can be assigned as the Pilot station of a Call Pickup group. 3-212 NWA-033623-001 Rev.8.1 91ch3002.fm...
Page 269: [Cm17] Acd/Ucd Group
CM17 COMMAND CODE TITLE: ACD/UCD GROUP FUNCTION: This command is used to define ACD (Automatic Call Distribution)/UCD (Uniform Call Distribution) groups. PRECAUTION: A maximum of 16 ACD/UCD groups can be assigned per system when using 8300R5 software or before. A maximum of 100 ACD/UCD groups can be assigned per system when using 8300R6 software or later.
Page 270 CM17 COMMAND CODE TITLE: ACD/UCD GROUP : Default STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Pilot station in Station number to Member station CM17 Y=0 ACD/UCD group be assigned as Pilot Pilot station XXXXXXXX Pilot station and Station number to OAI Member Member station for...
Page 271 CM17 COMMAND CODE TITLE: ACD/UCD GROUP : Default STATION NUMBER (A) SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING ACD/UCD service Pilot station Not provided CM17 Y=1 for Tie Line incom- number of ACD/ To provide ing call XXXXXXXX UCD group ACD/UCD service Pilot station...
Page 272: [Cm18] Station Hunting Group
CM18 COMMAND CODE TITLE: STATION HUNTING GROUP FUNCTION: This command is used to assign stations to a Station Hunting group. There are three hunt types; Station Hunting-Terminal, Station Hunting-Circular and Station Hunting-Secretarial. PRECAUTION: When a Station Hunting group requires a secretary station, it is necessary to assign CM18 Y=2. The maximum number of stations which can be assigned to a Station Hunting group is 60.
Page 273 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP DATA TABLE: Station Hunting-Terminal : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data When assigning station numbers to a Station Hunting group, only two station numbers can be assigned per operation.
Page 274 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station Secretary station number Secretary station serial numbers Secretary station should XXXXXXXX be Pilot station. Not assigned Operation: The correspondence between Serial numbers and Secretary station numbers is set by CM19.
Page 275 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Station Hunting-Circular : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data Example: When you define a Station Hunting-Circular group which consists of station numbers 310-312, the following three operations are required: Station No.
Page 276 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station: Secretary station number Secretary station serial numbers Operation: XXXXXXXX No data A B C D Secretary The correspondence between Serial numbers and Secretary station numbers is set by CM19.
Page 277 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP Station Hunting-Secretarial : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Next station number in Station number (A) Station number (B) Station Hunting group XXXXXXXX XXXXXXXX NONE No data Example: When you define Station Hunting-Secretarial group which consists of station numbers 320-323, the following four operations are required: Station No.
Page 278 CM18 COMMAND CODE TITLE: STATION HUNTING GROUP : Default STATION NUMBER (A) SETTING DATA MEANING DATA MEANING DATA MEANING Secretary station Secretary station number Secretary station serial numbers Operation: XXXXXXXX Not assigned The correspondence between Serial numbers and Secretary station numbers is set by Secretary CM19.
Page 279: [Cm19] Secretary/Group Diversion Station Number
CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER FUNCTION: This command is used to assign Secretary station numbers. And also, to assign transferred stations for Group Diversion. PRECAUTION: None ASSIGNMENT PROCEDURE: SECRETARY STATION DATA GROUP DIVERSION ST + SERIAL NUMBER (1-8 digits) GROUP (00-30) (00-30)
Page 280 CM19 COMMAND CODE TITLE: SECRETARY/GROUP DIVERSION STATION NUMBER : Default SECRETARY SETTING DATA STATION SERIAL MEANING DATA MEANING NUMBER Transferred station of Call 00: Group Diversion Station number transferred. Forwarding-No Answer for each Group group 00 Data “E000” (DESKCON) Diversion group XXXXXXXX is not provided.
Page 281: [Cm1B] Isdn Telephone Multipoint Station Number
CM1B COMMAND CODE TITLE: ISDN TELEPHONE MULTIPOINT STATION NUMBER FUNCTION: This command is used for an ISDN Telephone Multipoint station number. PRECAUTION: None ASSIGNMENT PROCEDURE: ISDN LINE ISDN DATA + 1B + STATION No. MULTIPOINT No. (1-8 digits) (1-8 digits) (0-7) DATA TABLE: 1ST DATA...
Page 282: [Cm1D] Ps-Id Assignment, Ps/Standard Sip Station Operation Data Download
CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT, PS/STANDARD SIP STATION OPERATION DATA DOWNLOAD FUNCTION: This command is used to assign the PS-ID, to download the PS/Standard SIP station operation data. PRECAUTION: When a PS is set up initially, set the PS in Data Download Mode by applying power to the PS while pressing the SEND key, and then execute the CM1D Y=20 in Calling Area No.
Page 283 CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT, PS/STANDARD SIP STATION OPERATION DATA DOWNLOAD : Default PS/STANDARD SETTING DATA RELATED SIP STATION COMMAND MEANING DATA MEANING Terminal type of PS X-XXXXXXXX Multiline Terminal PS II CM10 Y=04 [For PCS]/ (Primary/Subline Type with PS software ver- Terminal type of Standard PS Station No., sion 7.02 or later...
Page 284 CM1D COMMAND CODE TITLE: PS-ID ASSIGNMENT, PS/STANDARD SIP STATION OPERATION DATA DOWNLOAD : Default PS/STANDARD SETTING DATA RELATED SIP STATION COMMAND MEANING DATA MEANING Digest authentication to the X-XXXXXXXX Allowed CM10 Y=04 Standard SIP station (Standard SIP Restricted [8300R3.5] Station No.) Allowed NOTE 1: Be sure to set the second data to “03”...
Page 285: [Cm20] Numbering Plan/Single Digit Feature Access Code (Programmable)
CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) FUNCTION: Trunk routes and features are assigned by developing access codes. For Route Advance and Tenant development, see CM22 and CM23. The following figure shows the relationship between commands: For each access code Numbering Plan Route Advance Block...
Page 286 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) Name Display Registration From Multiline Terminal is as follows. • You can configure the station number from the Multiline Terminal to which the station number belongs. • Register the characters from PCPro/CAT to SLT, Multiline Terminal without LCD and Trunk. •...
Page 287 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) Character Table NUMBER OF TIMES ASSIGNMENT PROCEDURE: ACCESS CODE DATA + DE (1-4 digits) (1-4 digits) 3-231 NWA-033623-001 Rev.8.1 91ch3003.fm APRIL/16/2010...
Page 288 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) DATA TABLE: : Default SETTING DATA RELATED ACCESS CODE COMMAND DATA MEANING MEANING Numbering Plan X: 0-9, A (*), B (#) A004-A097 “SETTING CM29 Group 0 DATA: A004-A097” Numbering Plan XXXX 800-828 “SETTING...
Page 289 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A004-A097 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A004 Outgoing Trunk Queueing/Call Back/Call When Outgoing Trunk Queueing, Call CM15 Y=002, 003, Completion to Busy Subscriber (CCBS) Set Back and Completion of Calls to Busy 025, 157, 158 [For EU]...
Page 290 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A022 Do Not Disturb Set From station CM08>275 CM15 Y=019 A023 Do Not Disturb/Return Message Schedule Cancel A024 Wake Up Call/Timed Reminder Set CM15 Y=013 A025 Wake Up Call/Timed Reminder Cancel...
Page 291 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A043 Day Night Mode Change by Station Dialing CM15 Y=060 CM08>244, 245 A044 ACD/UCD Station Busy Out Set A045 ACD/UCD Station Busy Out Reset A046 Call Hold CM15 Y=001...
Page 292 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A070 Paging Answer Zone 0 CM30 Y=28 CM44 A071 Paging Answer Zone 1 CM15 Y=008 A072 Paging Answer Zone 2 CM08>157 A073 Paging Answer Zone 3 A074 Paging Answer Zone 4...
Page 293 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A090 Special Operator Call 0 CM90 A091 Special Operator Call 1 [8300R2] A092 Special Operator Call 2 [8300R2] A093 Special Operator Call 3 [8300R2] A094 Emergency Call...
Page 294 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: 800-828 SETTING DATA RELATED REMARKS COMMAND DATA MEANING Operator Call CM90 [8300R2] 1 digit Station 2 digits Station 3 digits Station 4 digits Station 5 digits Station For the following features, do not assign 5 or more digits station number.
Page 295 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A100-A199 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A100 Voice Response System Access Record CM10 CM15 Y=033 A101 Voice Response System Access Replay A102 Voice Response System Access Delete A103 Announcement Service Record CM10...
Page 296 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A126 LCR Group 0 CM8A Y=A000 A127 LCR Group 1 A128 LCR Group 2 A129 LCR Group 3 Assign A129 only when the LCR Group access code is included in the area code table in CM8A (Closed Numbering).
Page 297 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A146 Message Waiting/Message Reminder Search CM15 Y=047, 048 A147 Message Waiting/Message Reminder Retrieve CM13>03 A148 Message Reminder Set CM90 A149 Message Reminder Cancel A150 System Speed Dialing Origination For 1000 memories...
Page 298 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A181 Split Call Forwarding-All Calls Cancel A182 Split Call Forwarding-Busy Line/-No Answer A183 Split Call Forwarding-Busy Line/-No Answer Cancel A188 Whisper Page A189 Call Forwarding-Not Available Set A190...
Page 299 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: A230-A269 SETTING DATA RELATED REMARKS COMMAND DATA MEANING A230 Station Class change with Station Authorization CM42>73 Code A231 Station Authorization Code/Password Change CM42>73 A232 Pad Lock Set by Station Authorization Code A233 Pad Lock Reset by Station Authorization Code A234...
Page 300 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA RELATED REMARKS COMMAND DATA MEANING A259 Reverse Contrast on the LCD DT330/DT710/DT730 only CM13 Y=66 [8300R3] CM90 Y=00: F5033 A260 Do Not Disturb-Override/Call Forwarding-All CM90 Y=00: Calls Override F1080, F6103, [8300R5] F6108...
Page 301 CM20 COMMAND CODE TITLE: NUMBERING PLAN/SINGLE DIGIT FEATURE ACCESS CODE (PROGRAMMABLE) SETTING DATA: 100-515 SETTING DATA RELATED REMARKS COMMAND DATA MEANING Trunk Route 00 Data is to be assigned for Trunk CM30 Routes corresponding to the access Trunk Route 63 codes for outgoing trunk calls (COT, LDT, ODT, etc.).
Page 302: [Cm21] Single Digit Access Code
CM21 COMMAND CODE TITLE: SINGLE DIGIT ACCESS CODE FUNCTION: This command sets a single digit code to be recognized under timing start condition. PRECAUTION: None ASSIGNMENT PROCEDURE: ACCESS DATA + DE CODE (3/4 digits) (1 digit) DATA TABLE: SETTING DATA ACCESS CODE MEANING DATA...
Page 303: [Cm22] Route Advance
CM22 COMMAND CODE TITLE: ROUTE ADVANCE FUNCTION: This command is used to assign alternative trunk routes to each Route Advance Block. PRECAUTION: A maximum of seven consecutive priorities can be assigned. ASSIGNMENT PROCEDURE: PRIORITY DATA + DE 22YY ORDER (3 digits) (1 digit) DATA TABLE: : Default...
Page 304: [Cm23] Tenant Development
CM23 COMMAND CODE TITLE: TENANT DEVELOPMENT FUNCTION: Trunk routes and services are assigned by developing access codes for each tenant. For further development, use CM22 Route Advance. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT DATA + DE 23YY NUMBER (3/4 digits) (2 digits) DATA TABLE: : Default SETTING DATA...
Page 305: [Cm25] Kind Of Special Terminal Development
CM25 COMMAND CODE TITLE: KIND OF SPECIAL TERMINAL DEVELOPMENT FUNCTION: For each access code assigned to a special terminal block, a trunk route can be assigned based on which type of special terminal (ordinary station or FAX station) is placing the call. For special terminal assign- ments requiring development of route advance data for trunk route assignment, route advance develop- ment and the corresponding trunk routes are assigned using CM22.
Page 306: [Cm29] Numbering Plan Tenant Group
CM29 COMMAND CODE TITLE: NUMBERING PLAN TENANT GROUP FUNCTION: When each tenant has its own numbering plan in a multiple-tenant system, all the tenants are divided into four groups. Numbering Plan Group data is then assigned on a tenant basis. PRECAUTION: If the data is not assigned (“NONE”), then Numbering Plan Group 0 is used for all tenants.
Page 307: [Cm2A] Id Code Assignment With Cpu/Development Block Number Assignment For Each Calling Party Number
CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER FUNCTION: This command assigns ID codes used for the Authorization Code/Forced Account Code/Remote Access to System (DISA) features with CPU and Development Block number for each calling party number. PRECAUTION: These ID codes are effective when CM08>216/217 are set to “0”.
Page 308 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Valid range of ID Code 0000-2999 ID Code Pattern number Authorization Code, Forced Account Code, and Remote Access to System (DISA) Authorization Code, Forced...
Page 309 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Calling party number is 0000-2999 ID Code Pattern Available used as the ID Code for number Not available Remote Access to...
Page 310 CM2A COMMAND CODE TITLE: ID CODE ASSIGNMENT WITH CPU/DEVELOPMENT BLOCK NUMBER ASSIGNMENT FOR EACH CALLING PARTY NUMBER : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING ID Code Development Authorization Code ID Code Development number Number 00-09 Forced Account Code NOTE: CM2A (Related Command: CM2A...
Page 311: Assignment/Voip Encryption Password Assignment
CM2B TITLE: COMMAND CODE AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/ STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT/STANDARD SIP STATION REGISTRATION PASSWORD ASSIGNMENT/VoIP ENCRYPTION PASSWORD ASSIGNMENT FUNCTION: This command is used to set up the Authorization Code per station for PAD Lock feature. Also used to set up the password for the ID registration of the IP Station, Station Digest Authentication and the VoIP Encryption.
Page 312 CM2B TITLE: COMMAND CODE AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/ STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT/STANDARD SIP STATION REGISTRATION PASSWORD ASSIGNMENT/VoIP ENCRYPTION PASSWORD ASSIGNMENT DATA TABLE: : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Authorization Station number Authorization Code Code per station...
Page 313 CM2B TITLE: COMMAND CODE AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/ STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT/STANDARD SIP STATION REGISTRATION PASSWORD ASSIGNMENT/VoIP ENCRYPTION PASSWORD ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Trunk Restric- Station number Unrestricted (RCA) CM12 Y=02 (Maximum 8...
Page 314 CM2B TITLE: COMMAND CODE AUTHORIZATION CODE PER STATION/IP STATION PASSWORD ASSIGNMENT/ STATION DIGEST AUTHENTICATION PASSWORD ASSIGNMENT/STANDARD SIP STATION REGISTRATION PASSWORD ASSIGNMENT/VoIP ENCRYPTION PASSWORD ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING IP Station regis- Password for Password CM08>513...
Page 315: [Cm30] Trunk Data
CM30 COMMAND CODE TITLE: TRUNK DATA FUNCTION: This command is used to assign characteristics to trunk lines and IPT (P2P CCIS) lines which have been defined by CM10. PRECAUTION: None ASSIGNMENT PROCEDURE: TRUNK DATA 30YY NUMBER (1-8 digits) (000-511) DATA TABLE: : Default SETTING DATA RELATED...
Page 316 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating system in Day Mode Trunk Line (Direct) Appearance CM30 Y=18 for incoming C.O. calls Trunk Line (Direct) Appearance + TAS Direct-In Termination CM30 Y=04 Direct-In Termination + Trunk Line (Direct) Appearance CM49, CM64...
Page 317 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating system in Night Same as CM30 Y=02 Mode for incoming C.O. calls NOTE 1, NOTE 2, (See NOTE 3 on CM30 Y=02) Direct-In Termination in Day Station number for Direct-In Termina- CM10, CM11 Mode...
Page 318 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING CIC (Circuit Identification Code) CIC000 used for ISDN-Primary Rate NOTE Interface voice channels CIC029 NONE No data Restriction of outgoing connec- Restricted CM60 tion during Night Mode Allow NOTE: Assign CIC to voice channels only.
Page 319 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk group number Identification of Trunk Group Busy CM44 Y=00: 11XX NOTE: Paging trunks cannot be Lamps on an external display device assigned to the Trunk Identification of Trunk Group Busy CM90 Y=00: Group Busy Lamp.
Page 320 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk number XXXX Trunk ID code NOTE NOTE ISDN subscriber number XXXX ISDN subscriber number CM30 Y=34 CM50 Y=05 Paging Answer Zone/Kind of X: Paging Answer Zone CM20 Y=0-3: Paging 0: Paging Answer Zone 0...
Page 321 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Handling of busy/not available C.O. line release CM41 Y=0>34 Automated Attendant/Remote Forward to TAS indicator CM30 Y=04, 05 Access to System Forward to Attendant Console CM49 Y=02 (DISA) destination in Day Mode [8300R2]...
Page 322 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Automated Attendant C.O. line release CM30 Y=30, 31 Handling of all PBR busy when Forward to TAS indicator 2nd announcement and DT are Forward to Attendant Console connected.
Page 323 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Terminating System in Mode A Trunk Line (Direct) Appearance CM30 Y=18 for incoming C.O. calls Trunk Line (Direct) Appearance + TAS Direct-In Termination CM30 Y=05 Terminating System in Mode B Dial-in for incoming C.O.
Page 324 CM30 COMMAND CODE TITLE: TRUNK DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Direct-In Termination in Mode A Station number for Direct-In Termina- CM10, CM11 tion in Mode A XXXXXXXX Abbreviated code of System Speed CM71>66 Dialing for DIT-Outside CM35 Y=040 XX: 00-31 EBXXX...
Page 325 CM30 COMMAND CODE TITLE: TRUNK DATA SETTING DATA RELATED COMMAND MEANING DATA MEANING Association of BRT and Multiline Station number of Multiline Terminal CM41 Y=0>145 Terminal for power failure for power failure [8300R2] XXXXXXXX NOTE 1 NOTE 2 NOTE 1: The first data of this data can be assigned only a B1 channel trunk number of BRT.
Page 326: [Cm31] Mfc/Mf-Ani Trunk Data
CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA FUNCTION: This command is used to assign the attribute data to MFC/MF-ANI trunk lines. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE (1-2 digits) (1-2 digits) DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING...
Page 327 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Number of received digits of called 1 digit number from PSTN/T1 network 31 digits RESET NONE No data Signal pattern received from T1 network Called number + ANI [North America Only] Called number...
Page 328 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Received Backward GC signals on DOD Send G-I Signal First digit over GA MFC call Send G-I Signal Next digit over GA 01-15: Backward Group C1 - C15 Address complete, change over GB [Mexico Only] Congestion...
Page 329 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Backward signal meaning request of next Backward GA-1/GC-1 digit toward sending ANI signal on DOD MFC call Backward GA-15/GC-15 [8300R3.5] NONE No data NOTE: ANI function is effective when CM08>1200: 0.
Page 330 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Sending ACK-WINK signal to DTI on To send receiving MF signal Not sent [North America Only] NOTE: When the signal pattern from T1 network is FGD format, assign the data to “0”. When the signal pattern from T1 network is ANI format, assign the data “1”.
Page 331 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Tone Duration (Off time) of MFC (Forward 20 ms. Signal/Backward Signal) Increment unit: 20 ms. [8300R3.5] 1960 ms. 5100 ms. NONE 100 ms. NOTE: A reset by CM31 Y=A>90: 0 is required after this data setting.
Page 332 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Forward signal receiver minimum Detect -10/-15/-20/-25/-30/-35/-40 dBm Level -11/-16/-21/-26/-31/-36/-41 dBm (for Detect Level 0/1/2/3/4/5/6) -12/-17/-22/-27/-32/-37/-42 dBm [8300R3.5] -13/-18/-23/-28/-33/-38/-43 dBm -14/-19/-24/-29/-34/-39/-44 dBm -15/-20/-25/-30/-35/-40/-45 dBm -16/-21/-26/-31/-36/-41/-46 dBm -17/-22/-27/-32/-37/-42/-47 dBm -18/-23/-28/-33/-38/-43/-48 dBm...
Page 333 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Tone Duration (Off time) of MFC (Forward 1 dB Signal/Backward Signal) Increment unit: 1 dB [8300R3.5] 10 dB NONE 10 dB NOTE: A reset by CM31 Y=A>90: 0 is required after this data setting. Forward signal receiver S/N ratio 0 dB [8300R3.5]...
Page 334 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Backward signal receiver Detect Level Detect Level 0: 0 to -25 dBm [8300R3.5] Detect Level 1: -5 to -30 dBm Detect Level 2: -10 to -35 dBm Detect Level 3: -15 to -40 dBm Detect Level 4: -20 to -45 dBm Detect Level 5: -25 to -50 dBm...
Page 335 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Backward signal receiver Maximum Detect 0/-5/-10/-15/-20/-25/-30 dBm Level -1/-6/-11/-16/-21/-26/-31 dBm (for Detect Level 0/1/2/3/4/5/6) -2/-7/-12/-17/-22/-27/-32 dBm [8300R3.5] -3/-8/-13/-18/-23/-28/-33 dBm -4/-9/-14/-19/-24/-29/-34 dBm -5/-10/-15/-20/-25/-30/-35 dBm -6/-11/-16/-21/-26/-31/-36 dBm -7/-12/-17/-22/-27/-32/-37 dBm -8/-13/-18/-23/-28/-33/-38 dBm...
Page 336 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Backward signal receiver ON detect time 30 ms. [8300R3.5] Increment unit: 15 ms. 1485 ms. 3840 ms. NONE 30 ms. NOTE: A reset by CM31 Y=A>90: 0 is required after this data setting. Backward signal receiver OFF detect time 30 ms.
Page 337 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Duration from sending start Forward 1 second signal to receiving Backward signal Increment unit: 1 second [Not used in North America] 31 seconds NONE 12 seconds RESET...
Page 338 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Waiting duration from sending last 0 ms. Backward signal to sending Pulse Form sig- 50 ms. Increment unit: 50 ms. [Not used in Australia/ 600 ms.
Page 339 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Send first digit Backward Group A1 [8300R3.5] Backward Group A15 Send next digit (N+1) NONE No data [8300R3.5] Send last but one digit (n-1) [8300R3.5] Address complete, change over GB [8300R3.5]...
Page 340 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Subscriber’s Line Free (Charge) Backward Group B1 [8300R3.5] Backward Group B15 Subscriber’s Line Busy NONE No data [8300R3.5] Congestion [8300R3.5] Subscriber’s Line Free (No Charge) [8300R3.5] Subscriber’s Line Free (Call under control) [8300R3.5]...
Page 341 CM31 COMMAND CODE TITLE: MFC/MF-ANI TRUNK DATA : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Send G-I Signal First digit over GA Backward Group C1 [Mexico Only] [8300R5] Backward Group C15 NONE No data Send G-I Signal Next digit over GA [Mexico Only] [8300R5] Address complete, change over GB...
Page 342: [Cm35] Trunk Route Data
CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA FUNCTION: This command is used to assign trunk route characteristics. A trunk route is a group of trunks with com- mon characteristics used for a common purpose. PRECAUTION: When assigning a Tie line, the data in CM35 Y=009 (Incoming connection signaling) should be similar to that of CM35 Y=020 (Sender starting condition).
Page 343 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA The Commands of CM35 requiring blade reset after the data setting are as follows. : Blade reset is required –: Blade reset is not required *: The data is not effective BLADE TYPE Y No.
Page 344 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA ASSIGNMENT PROCEDURE: TRUNK DATA + 35YYY + ROUTE (1-8 digits) (2 digits) DATA TABLE: Y=000-098 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of Trunk Route DDD (C.O., DID, ISDN, SIP) trunk [North America Only] FX trunk WATS trunk...
Page 345 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Answer signal from distant Answer signal arrives (12 kHz, 50 Hz Metering CM41 Y=0 office for outgoing connec- signal) (C.O. line) tion Battery Reversal (C.O. line) Answer signal arrives (Tie line/ISDN/CCIS/SIP) No answer signal arrives...
Page 346 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Toll Restriction To provide CM81, CM8A Not provided CM85 CM35 Y=076 Number of digits to be 1 digit CM76 received on DID for Devel- 2 digits CM35 Y=018 opment Table 0...
Page 347 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of call termination C.O. Incoming Call 0 (Standard “LDN” key) CM90 indicator key/lamp on Atten- CM50 dant Console C.O. Incoming Call 7 FX Incoming Call 0 (Standard “FX” key) Call termination indicator [North America Only] lamps further categorized by...
Page 348 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Digit addition and deletion “0” add CM50 Y=00 on a Tie line incoming call “1” add NOTE: On an incoming “2” add call from a Tie line, “3”...
Page 349 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Sender prepause timing 0 second CM08>193, 194, 0.5 seconds 1.0 second 1.5 seconds 2.0 seconds 2.5 seconds 4.0 seconds 5.0 seconds 6.0 seconds 7.0 seconds 8.0 seconds 9.0 seconds 10.0 seconds...
Page 350 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING DTMF Inter-digital pause 32 ms. 64 ms. 80 ms. 96 ms. 160 ms. 192 ms. 240 ms. 128 ms. DP Make Ratio 39 % Make Ratio 33 % Make Ratio BLADE RESET PRECAUTION (2)
Page 351 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Interval of Multiline Termi- Ringing NOTE CM08>397 nal ringing signal to station Special Ringing CM08>397 on incoming calls Internal Ringing [Other than North External Ringing America] NOTE: For Multiline Terminal, Special Ringing;...
Page 352 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Multiline Terminal Ringer See below CM08>390 Tone Pattern on incoming CM15 Y=083, 084 calls CM65 Y=40 Multiline Terminal ringer tone pattern is assigned by the following combination of CM35 Y=034 and 164. : Default Y=34 Y=164: 0...
Page 353 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk access code sent to When a trunk is seized by a Trunk CM35 Y=189 SMDR for outgoing call/ Appearance key or LCR, one or two-digit code Trunk Access Code for (00-99) is sent out to the SMDR.
Page 354 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Restriction of outgoing con- Restricted CM12 Y=01 nection Allow CM35 Y=097 (Semi-Restricted-1) (RCD) Restriction of outgoing con- Restricted nection Allow (Semi-Restricted-2) (RCE) Restriction of outgoing con- Restricted nection Allow...
Page 355 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Restriction of incoming Restricted CM12 Y=01 connection to station Allow (Semi-Restricted-2) (RCE) Restriction of incoming Restricted connection to station Allow (Restricted-1) (RCF) Restriction of incoming Restricted connection to station Allow...
Page 356 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Designation of Area Code Area Code Development Pattern No. 0 CM8A Development Pattern No. for Y=4000-4007 Toll Restriction Area Code Development Pattern No. 7 CM85 Y=0-7 Analysis, and Maximum Not used...
Page 357 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Special facilities No. 7 CCIS, SIP trunk CM30 Y=35 ISDN-Basic Rate Interface ISDN-Primary Rate Interface Q-SIG (ETS300 172) Not used Common Channel Handler CCH00 CM30 Y=35 (CCH) number used for No.
Page 358 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Y=100-197 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Kind of CCIS Trunk CCIS Trunk (T1) NONE No data NOTE: When changing the data with online, the data is valid after the trunk blade is unplugged and plugged in. Call still Hold Available [Australia Only]...
Page 359 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING LAPD Mode of D-channel Network Mode route for WCS Roaming User Mode [For PCS] [8300R2] BLADE RESET PRECAUTION (2) LAPD Mode of D channel Network Mode route for Q-SIG User Mode...
Page 360 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING TOS field Precedence for PRECEDENCE 0 CM35 Y=161 SIP trunk voice packet TOS: Type of Service PRECEDENCE 7 PRECEDENCE 0 NOTE 1: The higher number has higher priority. NOTE 2: This data is recommended to set to “5”.
Page 361 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Calling party information To provide transfer to ISDN on tandem Not provided call from CCIS/SIP Calling party information To provide transfer to Enhanced 911/ Not provided MFC Signaling on DOD route on tandem call from...
Page 362 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Release of ISDN trunk when To release receiving the ISDN DIS- Not released CONNECT message with Progress Description=08 from ISDN (effective for an outgoing call to ISDN) NOTE: When sending the in-band tone to the calling station from ISDN, set the second data to 1.
Page 363 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Sending Switch Hook Flash To send for Adjunct Analog System Not sent DID Development Table Development Table 1 CM76 Y=00, 90 Development Table 0 NOTE: For SIP trunk, this data is available only for the Development Table 1.
Page 364 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk access code for Trunk Access Code to be added CM35 Y=044 Trunk-Direct Appearances X: 0-9, A (*), B (#) Multiline Operation NONE No data Tandem calls to CCT/IPT To provide CM35 Y=186...
Page 365 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Y=200-299 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN trunk tone sending To send Not sent Indication when a trunk is Trunk Route Name (4 characters) set to the Line Key of Multi- Trunk Route No.
Page 366 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Release of ISDN trunk when Not released receiving the ISDN DIS- To release CONNECT message with Progress Description=08 from ISDN (effective for an incoming call from ISDN) NOTE: When sending the in-band tone to the called station from ISDN, set the second data to 0.
Page 367 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Country Code for ETSI Country Code ISDN Addressing X: 0-9, A (*), B (#) [For EU] XXXX NONE No data Area Code for ETSI ISDN Area Code Addressing X: 0-9, A (*), B (#)
Page 368 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Release of ISDN trunk when To release CM35 receiving the ISDN DIS- Not released Y=266, 158, 208 CONNECT message with Progress Description=08 from ISDN because the called party is busy in tan- dem connection (ISDN to ISDN)
Page 369 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Forced release in designated To provide time for incoming trunk Not provided route Warning SST sending timer Depends on Timer A (CM41 Y=0>114) CM35 Y=247 for forced release to the Depends on Timer B (CM41 Y=0>115) CM41 Y=0>114...
Page 370 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Specification of the call ter- To transfer to the VRS/another station/ CM35 Y=256, 258 minating method for incom- Attendant Console (assigned by CM51 Y=33) CM51 Y=33 ing call with no CLI in Night To reject the call termination...
Page 371 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Dial Tone (DT) sending to To send DT of own office calling party of opposite To send DT of own office when the received office when receiving the Progress Description is not same as the Progress SETUP ACK message by...
Page 372 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN Alternative Routing Allow for Remote Unit in survival Restricted mode when receiving trunk call Call Completion to Busy Allow Subscriber (CCBS) for a call Restricted originating office [For EU]...
Page 373 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Calling party number relay- To provide CM35 Y=281 ing in ISDN to ISDN/CCIS Not provided to ISDN connection (for out- going trunk route) [For EU] NOTE 1: This command must be set for outgoing trunk route.
Page 374 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of PAD data from a -15 dB station to a trunk (1 dB increment) -1 dB 0 dB +1 dB (1 dB increment) +15 dB NONE 0 dB...
Page 375 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of PAD data from a -45 dB trunk to a conference trunk (1 dB increment) (Effective for LDT/ODT/ -1 dB PRT/DTI/CCT/SIP/IPT 0 dB [P2P CCIS]) +1 dB [8300R3]...
Page 376 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Polarity Detection of COT To detect [8300R4] Polarity free BLADE RESET PRECAUTION (2) Continued on next page 3-320 NWA-033623-001 Rev.8.1 91ch3003.fm JANUARY/31/2012...
Page 377 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA Y=302-999 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Paging station (PGD(2)- Restricted U10) access from trunk Allow [8300R4] Sending the Calling Party Available CMBA Y=44 Number when calling from Not available tandem connection [8300R5] NOTE 1:...
Page 378 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Whether to add the prefix To add CM35 Y=307, 308 code for Calling Party Not added CM8A Number when calling from a Y=5XXX>176 station CMBA Y=44 [8300R5] NOTE 1:...
Page 379 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING VRS Waiting Message To provide VRS Waiting Message function CM76 Y=45-48 (for Day Mode) (Announcement Service Start after Call Termi- [8300R7] nation) To provide VRS Waiting Message (Greeting VRS Waiting Message Mode) (for Night Mode)
Page 380 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING 2nd VRS Waiting Message VRS Waiting Message No. 00-63 CM76 Y=53-56 (for Day Mode) [8300R7] NONE No data 2nd VRS Waiting Message (for Night Mode) [8300R7] 2nd VRS Waiting Message (for Mode A)
Page 381 CM35 COMMAND CODE TITLE: TRUNK ROUTE DATA : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Multiple connections of Play the message any time CM76 Y=61-64 VRS Waiting Message Play the beginning of the message (for Day Mode) [8300R7] Multiple connections of VRS Waiting Message (for Night Mode) [8300R7]...
Page 382: [Cm36] Restriction Data/Pad Data For Tandem Connection
CM36 COMMAND CODE TITLE: RESTRICTION DATA/PAD DATA FOR TANDEM CONNECTION FUNCTION: This command is used to assign restriction data and PAD data for tandem connection within a system, for each combination of an incoming trunk route and an outgoing trunk route. PRECAUTION: Any incoming trunk route assigned to “No release signal”...
Page 383 CM36 COMMAND CODE TITLE: RESTRICTION DATA/PAD DATA FOR TANDEM CONNECTION DATA TABLE: : Default INCOMING OUTGOING RELATED TRUNK TRUNK SETTING DATA COMMAND MEANING ROUTE ROUTE Setting of restric- Allow CM35 Y=005 tion data for tan- Restricted dem connection Setting of PAD aa bb aa : PAD data from an incoming CM35 Y=005...
Page 384: [Cm40] Function Of Cpu Rs-232C Port
CM40 COMMAND CODE TITLE: FUNCTION OF CPU RS-232C PORT FUNCTION: This command is used to assign the function of the RS-232C ports on the CPU blade. The CPU blade has two RS-232C ports, which are used for the following purpose. : To assign –: Not assigned ( ): Port Location Number RS-232C PORTS ON THE CPU BLADE UNIT01...
Page 385 CM40 COMMAND CODE TITLE: FUNCTION OF CPU RS-232C PORT : To assign –: Not assigned ( ): Port Location Number RS-232C PORTS ON THE CPU BLADE UNIT01 UNIT02 UNIT03 UNIT04 FUNCTION REMARKS PORT PORT PORT PORT PORT PORT PORT PORT ...
Page 386 CM40 COMMAND CODE TITLE: FUNCTION OF CPU RS-232C PORT PRECAUTION: The condition of connecting PCPro to the RS-232C is as follows. - When connecting PCPro to the RS-232C ports other than Unit01, the connection depends on the data setting by the first data “0/1” (Port 1/Port 2 of Unit01) of CM40 Y=01-06. - For maintenance of whole system, PCPro must be connected to RS-232C port of Unit01.
Page 387: [Cm40] Cpu Rs-232C Port
CM40 COMMAND CODE TITLE: CPU RS-232C PORT DATA TABLE: CPU RS-232C port for PCPro/VoIP Log Collection/Built-in SMDR/MCI : Default SETTING DATA PORT LOCATION NUMBER REMARKS MEANING DATA MEANING Function UNIT01 PORT1 VoIP log collection UNIT01 PORT2 UNIT02 PORT1 MCI and Built-in [8300R2] NOTE 1 SMDR...
Page 388 CM40 COMMAND CODE TITLE: CPU RS-232C PORT : Default SETTING DATA PORT LOCATION NUMBER REMARKS MEANING DATA MEANING CS control UNIT01 PORT1 CS control is always UNIT01 PORT2 provided UNIT02 PORT1 As per CS signal [8300R2] NOTE 1 input UNIT02 PORT2 Data speed 1200 bps [8300R2]...
Page 389: [Cm40] Cpu Built-In Modem
CM40 COMMAND CODE TITLE: CPU BUILT-IN MODEM CPU Built-In Modem : Default 1ST DATA SETTING DATA RELATED COMMAND DATA MEANING MEANING DATA MEANING CPU Built-In Station number of Built-in modem No. CM08>909 Modem built-in modem X: 0-9, A (*), B (#) CM13 Y=07 NOTE 1 XXXXXXXX...
Page 390: [Cm41] System Timer Data
CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA FUNCTION: This command is used to assign the System Timer data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 41Y + (2 digits) (2 digits) DATA TABLE: 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER...
Page 391 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timing for Pseudo- NONE 00 01 02 03 04 05 06 07 08 Answer signal sent to 12 16 20 24 28 32 36 SMDR 4 seconds 12 16 20 24 28 32 36 40 seconds...
Page 392 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Attendant Recall of NONE 01 02 03 04 05 06 ....... 13 held call 31.2 2.4 4.8 7.2 9.6 12.0 ....28.8 31.2 2.4 seconds [8300R2] 33.6 2.4 4.8 7.2 9.6 12.0 14.4 ....
Page 393 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Unanswered timing NONE 01 02 03 ............30 for ACD/UCD Delay 8 ............116 Announcement and Attendant Delay 12 ............120 Announcement seconds 4 seconds Maximum ACD/UCD NONE 01 02 03 ............30 call waiting time 8 ............116...
Page 394 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Automatic Recall NONE 01 02 03 04 05 .........15 Timing of Camp-On 16 24 32 40 ........120 8 seconds 16 24 32 40 48........128 seconds Interdigit Pause on NONE 03 04 05 06 07 .........14...
Page 395 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Programmable Pause NONE 00 01 02 03 04 05 06 07 for System Speed 1.5 3.0 4.5 6.0 7.5 9.0 10.5 12.0 Dialing/Station Speed 1.5 seconds seconds NOTE: This pause is available by setting “D”...
Page 396 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Announcement Ser- NONE 01 02 ..............99 vice Timer 4 ..............392 4 seconds 8 ..............396 seconds Timing of Multiple NONE 01 02 03 ..........29 Call Forwarding No 8 ..........
Page 397 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Message Replay Timer NONE 01 02 03 ............31 for Automated Atten- 12 ............124 dant 12 16 ............128 seconds NOTE: In case that the recording time of Voice Re- 4 seconds sponse System is shorter than the time assigned by command (CM41Y=0>51), Voice Response...
Page 398 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Message replay timer/ NONE 01 02 03 ............99 tone sending timer in 8 ............392 the OAI terminal 4 seconds mode 12 ............396 seconds Timing Start when NONE 03 04 05 ............14 making an ISDN Tan-...
Page 399 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER SST Sending Timer NONE 01 02 03 ............14 when accessing Pag- 1440 0 480 960 ............6240 ing Trunk 480 ms. 1920 480 960 1140.............6720 Time Out Check when NONE 01 02 03..........30...
Page 400 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Recall interval timer NONE 45 46 ..............99 of built-in modem on 180 184 ...............396 4 seconds seconds [8300R3] Message duration for NONE 01 02 ..............99 Announcement 8 ..............396 Service-PS/Standard...
Page 401 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Message reply timer NONE 01 02 ..............99 for PS/Standard SIP 4 ..............392 station No Answer 4 seconds 8 ..............396 seconds NOTE: Effective only when CM08>085: 0. Timer of Dial Tone NONE 05 06 07 ............30...
Page 402 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER SPDT Timer after NONE 10 11 12 ............60 Hooking 1 second 10 11 12 ............60 seconds Inter-digit Pause on NONE 01 02 03 04 05 06 07 16/32/48 ms.
Page 403 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timer A of warning NONE 01 02 03 ............99 SST sending for – 64 128 192 ............6336 forced release NOTE: Set the time from the start of communications 64 seconds to the warning SST is sent.
Page 404 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timing of Caller ID NONE 00 01 02 ............25 station until sending 1500 ms. 0 100 200 ............2500 Caller ID signal after (CM08> the first ringer begins 100 ms.
Page 405 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Expire value for NONE 00 01 02 ............99 DT700 Series SUB- 1 hour 2 ............99 SCRIBE for Server NOTE 1: Usually, this data setting is not required. (Day) NOTE 2: This data implies the expire value for the DT700 Series...
Page 406 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Expire value for NONE 00 01 02 ............99 DT700 Series SUB- 1 hour 2 ............99 SCRIBE for Client NOTE 1: Usually, this data setting is not required. (Day) NOTE 2: This data implies the expire value for the DT700 Series...
Page 407 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Conference (built-in NONE 01 02 03 ............24 CPU) forced release 7 hours 3 ............24 1 hour timer NOTE: If this data is set to “00”, forced release is not provided. [8300R2] D11 data receiving NONE...
Page 408 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Periodic registration NONE 00 01 02 ............99 timer for Standard SIP 0 day 2 ............99 station NOTE 1: Be sure to reset Standard SIP station when this data set- - Day ting is changed.
Page 409 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Timing until sending NONE 00 01 02 ............99 the reverse signal to Not 4 8 ............396 Standard SIP station seconds sent 4 seconds [8300R3.5] NOTE: This data is effective only when the 2nd data of CM41 Y= 0>110 is set to NONE.
Page 410 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Remote maintenance NONE 01 02 03 ....... 20 permission timer 5 minutes 10 20 30 ...... 200 1440 [8300R7] NOTE 1: Remote maintenance permission timer is not started up when this data is set to “00”.
Page 411 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Hold-tone timer NONE 01 02 03 ............30 between the 1st and 32-36 8 ............116 the 2nd VRS Waiting 4 seconds seconds Message 12 ............120 [8300R7] Continued on next page 3-355 NWA-033623-001 Rev.8.1...
Page 412 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Delayed Ringing NONE 03 ..........20 2048 ms. Timer 10240 ms. 2048 4096 6144 ..........40960 Switch Control Screen NONE of LCD Pattern A/B [North America Control Control –...
Page 413 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER C.O. Trunk Termina- NONE 01 02 03 ............99 tion Detect Timer 8 ms. 224 ms. 16 24 ............792 BLADE RESET Single Ringing Detect NONE 01 02 03 ..........98 16 ms.
Page 414 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER COT Ground Starting NONE 01 02 03 ..........98 8 ms. Timer 48 ms. 16 24 ..........784 2040 (01-98) BLADE RESET OD Trunk Answer NONE 01 02 03 ..........98 20 ms.
Page 415 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER LD Wink signal send- NONE 01 02 03 ..........98 ing time for connection 20 ms. 200 ms. 20 40 60 ...........1960 2550 check (01-98) BLADE RESET LD Trunk Delay Signal NONE 01 02 03 ..........98...
Page 416 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER OD Wink/Delay Send- NONE 01 02 03 ..........98 ing start Time after 100 ms. 100 200 300 ..........9800 25500 100 ms. Incoming (01-98) [8300R6] BLADE RESET OD Wink/Delay NONE 01 02 03 ..........98...
Page 417 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER OD Receive DP Break NONE 01 02 03 ..........98 Maximum Time 2 ms. 100 ms. 6 ..........196 [8300R6] (01-98) BLADE RESET LD Receive DP Make NONE 01 02 03 ..........98 Minimum Time...
Page 418 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Answer Signal Detect NONE 01 02 03 ..........98 Timing on DTI (T1 1.5 8 ms. 60 ms. 16 24 ..........784 1020 Mbps) trunk (01-98) BLADE RESET NONE 01 02 03 ..........98 Release Signal Detect...
Page 419 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER Loop Current Detect NONE 01 02 03 ..........98 Timing for DTI 48 ms. 16 32 48 ...........1568 4080 16 ms. (E1 2 Mbps) trunk (01-98) [8300R3] BLADE RESET Clear Signal Detect...
Page 420 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER DTI (E1 2 Mbps) trunk NONE 01 02 03 ..........98 Receive Answer maxi- 400 ms. 128 256 384 .........12544 16320 128 ms. mum time (01-98) [8300R3] BLADE RESET DTI (E1 2 Mbps) trunk...
Page 421 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER DTI (E1 2 Mbps) trunk NONE 01 02 03 ..........98 Transmit Digit 100 ms. 16 24 ..........784 1020 Acknowledge duration 8 ms. time (01-98) [8300R3] BLADE RESET DTI (E1 2 Mbps) trunk NONE...
Page 422 CM41 COMMAND CODE TITLE: SYSTEM TIMER DATA 2ND DATA INCREMENT MEANING DEFAULT DATA UNIT TIMER DTI (E1 2Mbps) trunk NONE 01 02 03 ..........98 Transmit Seizure Sig- 800 ms. 16 32 48 ...........1568 2040 16 ms. nal time (01-98) [8300R3] BLADE RESET MFC-R2 Backward NONE...
Page 423: [Cm42] System Counter Data/Pad Data/Trunk Restriction Class Conversion/Codec List
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA/TRUNK RESTRICTION CLASS CONVERSION/CODEC LIST FUNCTION: This command is used to set the system counter data, the programmable PAD data, the Trunk Restriction Class data to convert the Restriction Class sent to or from the 2400 IPX as a Deluxe Traveling Class Mark-CCIS, and CODEC list.
Page 424 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA DATA TABLE: System Counter Data/PAD Data : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Number of waiting calls which will cause 1 call attendant’s CWXX on LCD to flash [DESKCON] 48 calls [8300R2] NONE...
Page 425: [Cm42] System Counter Data/Pad Data
CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Maximum number of digits for Account Code 1 digit with OAI (SCF) 10 digits NONE 10 digits Maximum number of digits for Account Code 1 digit with CPU 16 digits...
Page 426 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Maximum number of calls in queue in each 1 call ACD/UCD group for controlling external 99 calls indicator or Call Waiting lamp of Multiline NONE 1 call Terminal...
Page 427 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Volume Control (Side tone level) of Multiline –54 dB 6 dB Terminal/DESKCON increments –18 dB NONE –30 dB NOTE 1: Do not change this data normally, incorrect data settings may cause howler of low-level speech. NOTE 2: For the volume control (Side tone level) of DT300/DT700 series, set the data by CM42>198.
Page 428 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Maximum number of Wake Up Call setting at 1 call CM08>850 the same time 32 calls NONE No limit NOTE: Assign the maximum number of Wake Up Call for the same time per every minute. Time for monitoring long call duration of 1 hour CM35 Y=286...
Page 429 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Setting of PAD data from a station/trunk to a -45 dB Conference Trunk for a Conference Trunk (1 dB increment) connection -1 dB 0 dB +1 dB (1 dB increment)
Page 430 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Volume Control of Desk Console (Sending Level 00 (Low Level) level) [8300R2] Level 31 (High Level) NONE The default data is different depending on the specifications of each country.
Page 431 CM42 COMMAND CODE TITLE: SYSTEM COUNTER DATA/PAD DATA : Default KIND OF SYSTEM COUNTER/PAD DATA SETTING DATA REMARKS Setting of PAD data from a station to a DTMF -45 dB Receiver (For SLT) [8300R4] -1 dB 0 dB 1 dB 18 dB NONE 0 dB...
Page 432: [Cm42] Trunk Restriction Class Conversion
CM42 COMMAND CODE TITLE: TRUNK RESTRICTION CLASS CONVERSION Trunk Restriction Class Conversion SV8300 represents small model PBX system. 2400 IPX represents medium to large model PBX system. : Default 1ST DATA 2ND DATA REMARKS DATA MEANING DATA MEANING SV8300 Trunk Restriction Class 1 (RCA) 2400 IPX Trunk Restriction Class (0-15) SV8300 Trunk Restriction Class 2 (RCB)
Page 433 CM42 COMMAND CODE TITLE: TRUNK RESTRICTION CLASS CONVERSION NOTE 1: Default in the DATA TABLE represents the value for the data “NONE”. In this case, the fol- lowing conversion is performed in the Deluxe Traveling Class Mark-CCIS. (1) 2400 IPX to SV8300 2400 IPX SV8300 TRK RESTRICTION CLASS...
Page 434: [Cm42] Codec List
CM42 COMMAND CODE TITLE: CODEC LIST CODEC List : Default 1ST DATA (CODEC TYPE) 2ND DATA REMARKS DATA MEANING DATA MEANING Priority 1-4 in CODEC list 0 G.711 µ-law 64 K NOTE 1 CM67 NOTE 1 G.711 A-law 64 K G.723.1 (5.3/6.3K) NOTE 4 G.729a...
Page 435 CM42 COMMAND CODE TITLE: CODEC LIST : Default 1ST DATA (PAYLOAD SIZE) 2ND DATA REMARKS DATA MEANING DATA MEANING Priority 1-4 in CODEC list 0 10 ms. CM67 40 ms. NOTE 1, NOTE 2, NOTE 3 Priority 1-4 in CODEC list 1 NONE No data Priority 1-4 in CODEC list 2...
Page 436 CM42 COMMAND CODE TITLE: CODEC LIST NOTE 2: When using PZ-64IPLC-A/PZ-128IPLC-A (VoIPDB), the maximum number of connectable channels for simultaneous calls depends on the setting of payload size assigned by CM42> 110-113/130-133/150-153/170-173. MAXIMUM NUMBER OF CONNECTABLE CHANNELS FOR SIMULTANEOUS CALLS PAYLOAD SIZE G.729a G.711...
Page 437: [Cm43] Periodic Maintenance/Ip Station Firmware Automatic Update/System Data Copy/Automatic Clock Change
CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE FUNCTION: This command is used to set the date, time and check item for periodic maintenance. The fault informa- tion display reminds you of the time for each periodic maintenance. Page 3-678] [See CMEA Fault Information Display, fault kind No.
Page 438 CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE : Default MEANING MEANING 2ND DATA MEANING DATA 6 Time setting for IP IP Station firmware YYYY MM DD HH mm YYYY: Year (2011-2099) Station firmware auto- automatic update time : Month (01-12) matic update...
Page 439 CM43 COMMAND CODE TITLE: PERIODIC MAINTENANCE/IP STATION FIRMWARE AUTOMATIC UPDATE/SYSTEM DATA COPY/AUTOMATIC CLOCK CHANGE : Default MEANING MEANING 2ND DATA MEANING DATA 8 Time setting for Reading of system clock YYYY MM DD YYYY: Year (2011-2099) Automatic clock changed day from : Month (01-12) change standard time to...
Page 440: [Cm44] External Relay Starting Conditions
CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS FUNCTION: This command is used to assign the relay circuit number and Relay Group number of PGD(2)-U10 ADP/ External Relay Interface of CPU blade used for controlling external relay. PRECAUTION: For External Relay Interface of the CPU blade, assign 312, 313 (blade No. 31, circuit No. 2, 3). ASSIGNMENT PROCEDURE: RELAY RELAY...
Page 441 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS DATA 1 DATA 2 REMARKS DATA MEANING DATA MEANING External Hold Tone Machine Start External Hold Tone for Music on CM48 Y=0 (PGD(2)-U10 ADP) Hold [8300R3] External Announcement Machine External Announcement Machine CM48 Y=1 Start for wake up calling/Timed Reminder...
Page 442 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS The following table shows the interface condition of each external relay. EQUIPMENT KIND INTERFACE RELATED COMMAND REMARKS External Tone Source DLC + PGD(2)-U10 ADP • CM05 Y=0 • Start by External Relay Control [8300R3] •...
Page 443 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS EQUIPMENT KIND INTERFACE RELATED COMMAND REMARKS TAS Indication Built-in Relay on CPU • CM30 Y=13, 14 • Start by Built-in Relay on CPU • CM44 Y=00>312, 313: 13XX DLC + PGD(2)-U10 ADP • CM05 Y=0 •...
Page 444 CM44 COMMAND CODE TITLE: EXTERNAL RELAY STARTING CONDITIONS EQUIPMENT KIND INTERFACE RELATED COMMAND REMARKS No. 7 CCIS Day/Night DLC + PGD(2)-U10 ADP • CM05 Y=0 • Start by External Relay Control Status Display • CM10 Y=00 Circuit of PGD(2)-U10 ADP •...
Page 445: [Cm45] Make Busy Condition Of Cft/Dtmf Receiver Detect Level
CM45 COMMAND CODE TITLE: MAKE BUSY CONDITION OF CFT/DTMF RECEIVER DETECT LEVEL FUNCTION: This command is used to define the make busy condition of built-in CFT on CPU or to set DTMF Receiver detect level. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + 45Y + (2-3 digits)
Page 446 CM45 COMMAND CODE TITLE: MAKE BUSY CONDITION OF CFT/DTMF RECEIVER DETECT LEVEL : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of DTMF X 00 Receiver start delay time 0 ms. Receiver detect level X: Receiver Type (0-2) (0.25 ms.
Page 447 CM45 COMMAND CODE TITLE: MAKE BUSY CONDITION OF CFT/DTMF RECEIVER DETECT LEVEL : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of DTMF X 03 DTMF receiver maximum 0/-5/-10/-15/-20/-25/-30 dBm Receiver detect level detect level -1/-6/-11/-16/-21/-26/-31 dBm (Related command: (For Detect Level 0/1/2/3/4/ -2/-7/-12/-17/-22/-27/-32 dBm...
Page 448: [Cm48] Hold/Wake Up/Timed Reminder/Automated Attendant
CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE FUNCTION: This command determines the kind of tone/tone source on various services; it also determines whether the Announcement Service is provided when a PS does not answer in a Wireless Communication Sys- tem.
Page 449 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Wake Up Call/ Tone source of 0000 No Tone Timed Wake Up Call/ 0200 External Tone Source CM44 Reminder Timed Reminder [8300R3]...
Page 450 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Dial Tone Progress Tone for Not provided sending Last Number To provide Redial and Speed Dial when Using 2nd DT sending on To provide ISDN trunks...
Page 451 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Music selection Music selection Nocturne for Internal for Internal Hold Minuet Hold Tone Tone Fur Elise The Maiden’s Prayer When the saints go marching in Spring (by four seasons)
Page 452 CM48 COMMAND CODE TITLE: HOLD/WAKE UP/TIMED REMINDER/AUTOMATED ATTENDANT TONE : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Announcement – 0500 To provide CM12 Y=04 PS/Standard SIP NONE Not provided CM41 Y=0>01, station No Answer CM49 Y=00, 10 [8300R2] Announcement –...
Page 453: [Cm49] Voice Response System
CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM FUNCTION: This command is used to define the function of each Voice Response System (VRS) accommodated into the system. PRECAUTION: When 8300R7 software or later is used and CF memory is used for Voice Response System, VRS num- ber 000-015 can be used.
Page 454 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice XXX: VRS number 07 XX Transferred Trunk Line CM65 Y=51 Response System (000-007) Message Service (Busy) [8300R6 XX: Message No. (00-63) software or 08 XX Voice Message Waiting Ser-...
Page 455 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice XXX: VRS number 0F XX Attendant Delay CM49 Y=0A Announcement CM35 Y=074 Response System (000-007) [8300R6 XX: Message No. (00-63) CM41 Y=0>16, 47 software or [8300R2]...
Page 456 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Function of Voice XXX: VRS number 16 XX Multi-connection Announce- CM17 Y=1, A Response System (000-007) ment Service for OAI CM41 Y=0>67 [8300R6 XX: Message Group No.
Page 457 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Message No. of 1st 00-63: Tenant No. 00-63 Message No. assigned by CM49 Y=00 Answering Message CM49 Y=00 of Automated Atten- NONE No data dant...
Page 458 CM49 COMMAND CODE TITLE: VOICE RESPONSE SYSTEM : Default SETTING DATA VRS No./ RELATED TENANT No. COMMAND MEANING DATA MEANING Message No. of Voice 00: When Message 00-63 Message No. assigned by CM48 Y=2 Guide NOTE waiting is set CM49 Y=00 (Not available CM49 Y=00: 17XX 01: When service is for IP Station)
Page 459: [Cm4A] Day/Night Mode Change By System Clock, Automatic Rc/ Dnd Mode Select By System Clock
CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK FUNCTION: This command is used to assign the schedule of Day/Night Mode Change and Automatic RC/DND Mode select by System Clock. PRECAUTION: For Automatic Day/Night Mode Change •...
Page 460 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK DATA TABLE: : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Calendar No. 00-63 Tenant No. 00-63 Calendar No. 1 System Calendar No.
Page 461 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Time schedule No. 0 XX ZZ XX : 00-23: Hour Day Mode Time schedule No.
Page 462 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING System Service No. 0 Room cut off (RC) [8300R3] Do not Disturb (DND) Reset System Service No.
Page 463 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK • Default Pattern By assigning CM4A Y=90; Default Pattern No. 0-3, you can simplify the schedule assignment for each tenant. The schedule of each Default Pattern can be changed after the Default Pattern has been assigned. The following shows the summary of the Default Pattern and the schedule set by each Default Pattern.
Page 464 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK Default Pattern of Time Schedule (CM4A Y=90) • Default Pattern No. 0 (CM4A Y=90 2nd data: 00) CM4A Y No. MEANING OF SETTING 00-63 Calendar No.
Page 465 CM4A COMMAND CODE TITLE: DAY/NIGHT MODE CHANGE BY SYSTEM CLOCK, AUTOMATIC RC/ DND MODE SELECT BY SYSTEM CLOCK Default Pattern of Time Schedule (CM4A Y=90) • Default Pattern No. 2 (CM4A Y=90 2nd data: 02) CM4A Y No. MEANING OF SETTING 00-63 Calendar No.
Page 466: [Cm4B] Room Status Code
CM4B COMMAND CODE TITLE: ROOM STATUS CODE FUNCTION: This command is used to assign the functions for each Room Status Code which is dialed from a guest room or a Front Desk Terminal. PRECAUTION: None ASSIGNMENT PROCEDURE: 2ND DATA 1ST DATA + 4BYY + + EXE (3 digits)
Page 467 CM4B COMMAND CODE TITLE: ROOM STATUS CODE : Default 1ST DATA 2ND DATA RELATED COMMAND DATA MEANING DATA MEANING Change of Trunk Restriction Unrestricted (RCA) Class Non-Restricted 1 (RCB) X: Room Status Code 1-8 Non-Restricted 2 (RCC) Semi-Restricted 1 (RCD) Semi-Restricted 2 (RCE) Restricted 1 (RCF) Restricted 2 (RCG)
Page 468: [Cm50] Common Route Indial
CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL FUNCTION: This command is used to assign LDNs (Listed Directory Numbers) to common route indial lines. When these numbers are dialed into the system (either on an incoming tie line or an incoming C.O. line set up for indialing), the call will appear at a specified call identification key on the attendant console.
Page 469 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL DATA TABLE: : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Two leading digits to be added Digits to be added NOTE 1: CM35 Y=017 allows digits to be added or (2 digits) deleted from indialed digit streams on a NONE...
Page 470 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Effective data in CM35 Y=015 Dialed number NOTE 2 LDN 0 key (Data 00 in CM90) XXXX LDN 7 key (Data 07 in CM90) NOTE 1 (1-4 digits) NONE...
Page 471 CM50 COMMAND CODE TITLE: COMMON ROUTE INDIAL : Default KIND OF DATA SETTING DATA CODE MEANING DATA MEANING Pattern number for adding an access code for outgo- Access Code for outgoing ing call to the calling number recalled by Message call Reminder when terminating a SIP trunk or a tandem XXXXXX...
Page 472: [Cm51] Automatic Transfer Destinations
CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS FUNCTION: This command is used to define destinations for different types of diversion. PRECAUTION: None ASSIGNMENT PROCEDURE: GROUP DATA + 51YY + NUMBER (1-8 digits) (2 digits) DATA TABLE: : Default GROUP NUMBER SETTING DATA MEANING DATA...
Page 473 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Same as CM51 Y=06 (for station call) Tenant 00 E000 Attendant Console [8300R2] Tenant 63 EBXXX Voice Response system No. XXX: 000-007 [8300R6 software or before]...
Page 474 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Transfer destination of the call when the Tenant 00 Station No. Room Cutoff station dials C.O. access code Tenant 63 XXXXXXXX Transfer destination of Off-Hook Alarm/Prior- E000 Attendant Console ity Call 0/1...
Page 475 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Destination of the call from the station to Tenant 00 Station No./VMS which Message Waiting has been set/VMS Station No. station for each tenant CM13 Y=13 Tenant 63 XXXXXXXX...
Page 476 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Transfer destination of call forwarding by Tenant 00 Station No. Queue Limit for TAS/Overflow for TAS Tenant 63 Queue (for Day Mode) XXXXXXXX CM49 Y=00: 1800 E000...
Page 477 CM51 COMMAND CODE TITLE: AUTOMATIC TRANSFER DESTINATIONS : Default GROUP NUMBER SETTING DATA MEANING DATA MEANING DATA MEANING Destination of Call Forwarding-Logout Tenant 00 EBXXX Voice Response (IP Station) CM49 Y=00: 21 XX system No. Tenant 63 XXX: 000-007 [8300R6 software or before] : 000-015...
Page 478: [Cm52] Hot Line/Delayed Hotline
CM52 COMMAND CODE TITLE: HOT LINE/DELAYED HOTLINE FUNCTION: This command is used to assign a Hot Line/Delayed Hotline to stations, Attendant Consoles and trunks. PRECAUTION: The maximum number of Hot Lines/Delayed Hotlines is 100, and the connection is one-way from calling side to called side.
Page 479 CM52 COMMAND CODE TITLE: HOT LINE/DELAYED HOTLINE DATA TABLE: Hot Line/Delayed Hotline : Default SETTING DATA CALLING/CALLED MEANING DATA MEANING Hot Line/Delayed Calling Side Station No./Virtual Station No. Hotline Pair CM12 Y=03 number 00-99 XXXXXXXX NOTE NONE No data Called Side Station No.
Page 480: [Cm53] Trunk Answer From Any Station Restriction
CM53 COMMAND CODE TITLE: TRUNK ANSWER FROM ANY STATION RESTRICTION FUNCTION: This command is used to define the conditions for Trunk Answer from Any Station (TAS) service. PRECAUTION: None ASSIGNMENT PROCEDURE: CONDITION CODE DATA + DE (1 digit) (1 digit) DATA TABLE: : Default CONDITION...
Page 481: [Cm56] Paging Group/Intercom Group
CM56 COMMAND CODE TITLE: PAGING GROUP/INTERCOM GROUP FUNCTION: This command is used to assign the Multiline Terminal/Soft Phone station number for Automatic/ Manual/Dial Intercom and Internal Zone Paging. PRECAUTION: None ASSIGNMENT PROCEDURE: SERIAL No. INTERCOM No. DATA 56YY + DE (2 digits) (4 digits) (1-8 digits)
Page 482 CM56 COMMAND CODE TITLE: PAGING GROUP/INTERCOM GROUP SETTING DATA INTERCOM No./ RELATED SERIAL No. COMMAND MEANING DATA MEANING Simultaneous Paging 00-15: Serial number My Line number of CM90 Group 0 within the group Multiline Terminal XXXXXXXX Simultaneous Paging NONE No data Group 7 Automatic Intercom A000...
Page 483 CM57 TITLE: COMMAND CODE GROUP CALL, MY LINE NUMBER THAT DISPLAYS THE CALLING NUMBER, SERIAL NUMBER WITHIN THE CONFERENCE GROUP, CONFERENCE PILOT STATION FOR THE OUTGOING CALL, PILOT STATION FOR THE SERVICE ORIGINATING CALL FOR EACH TENANT, SUITE ROOM GROUP NUMBER FUNCTION: This command is used to assign the Group Call numbers and stations for Group Call by Pilot Number Dialing, and the My Line number that displays the calling number, the Serial number within the Confer-...
Page 484 CM57 TITLE: COMMAND CODE GROUP CALL, MY LINE NUMBER THAT DISPLAYS THE CALLING NUMBER, SERIAL NUMBER WITHIN THE CONFERENCE GROUP, CONFERENCE PILOT STATION FOR THE OUTGOING CALL, PILOT STATION FOR THE SERVICE ORIGINATING CALL FOR EACH TENANT, SUITE ROOM GROUP NUMBER : Default 1ST DATA 2ND DATA...
Page 485: [Cm58] Ldn Diversion
CM58 COMMAND CODE TITLE: LDN DIVERSION FUNCTION: This command is used to assign information to each DID or TIE trunk for which incoming calls are to be redirected to an alternative destination. PRECAUTION: This data is valid when CM08>205 is assigned to “0”. ASSIGNMENT PROCEDURE: LDN/TIE DATA...
Page 486 CM58 COMMAND CODE TITLE: LDN DIVERSION : Default SETTING DATA MEANING DATA MEANING Tenant number of LDN assigned by Tenant 00 CM50 Y=01 Tenant 63 NONE No data TAS group number assigned by TAS Group 00 CM44>13 TAS Group 63 NONE No data Day Mode destination of LDN...
Page 487 CM58 COMMAND CODE TITLE: LDN DIVERSION : Default SETTING DATA MEANING DATA MEANING Night Mode diversion for non- Same as CM58 Y=06 answering destination station NONE No data Day Mode station number/Abbreviate Station No. Code for outside party (LDN-Outside) XXXXXXXX Abbreviated Code for outside party XX: 00-31 CM71>66...
Page 488: [Cm59] Tas/Acd/Ucd Relay Interruption Pattern
CM59 COMMAND CODE TITLE: TAS/ACD/UCD RELAY INTERRUPTION PATTERN FUNCTION: This command is used to assign the interruption pattern on the TAS and ACD/UCD indicators controlled via External Relay Interface of CPU. PRECAUTION: None ASSIGNMENT PROCEDURE: FUNCTION DATA + 59 + NUMBER (2 digits) (2 digits)
Page 489: [Cm5B] Ip Address For Ip Trunk/Sip Trunk Point-To-Multipoint Connection
CM5B COMMAND CODE TITLE: IP ADDRESS FOR IP TRUNK/SIP TRUNK POINT-TO-MULTIPOINT CONNECTION FUNCTION: This command is used to assign the destination IP Address for the IP trunk/SIP trunk Point-to-Multipoint connection. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE 5BYY (5 digits) (12 digits)
Page 490 CM5B COMMAND CODE TITLE: IP ADDRESS FOR IP TRUNK/SIP TRUNK POINT-TO-MULTIPOINT CONNECTION NOTE 3: IP address number (00-07) of the first data is set as follows. Example1: IP trunk (P2P CCIS) - IP address number (00-07) the number for specifying the IP address of oppo- site office which has plural IP addresses, when the offices are connected with Point-to-Multipoint.
Page 491: [Cm60] Att Tenant Group, Functions
CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS FUNCTION: This command is used to assign a number to a Desk Console for access on a tenant basis, and define the consoles’ night switching ability, off-hook ringing, tone ringer, password code for Attendant Lockout and Attendant Programming.
Page 492 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS DATA TABLE: : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING ATT GROUP NOTE 1, NOTE 2 ATT GROUP 0 CM41 Y=0>142 ATT GROUP 1 CM62 ATT GROUP 2 CM51 Y=13 ATT GROUP 3 CM60 Y=90 NONE No data...
Page 493 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING 600 + 700  16 (Hz) Tone Ringer for DESKCON CM60 Y=90 480 + 606  8 (Hz) NOTE 2 1024 + 1285  16 (Hz) 480 + 606 ...
Page 494 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS : Default GROUP NUMBER RELATED COMMAND MEANING DATA MEANING Displaying pattern of Caller ID on To display calling number on upper the LCD of DESKCON before line of LCD, calling name on answering or after answering a middle line of LCD trunk call...
Page 495 CM60 COMMAND CODE TITLE: ATT TENANT GROUP, FUNCTIONS NOTE 4: These data are effective for Day/Night Mode Change key on DESKCON. NT switch is effec- tive only on the Master ATT assigned by CM60 Y=01. NOTE 5: After this data setting, a reset of DESKCON is required. NOTE 6: The second data can only be set to 0.
Page 496: [Cm61] External Key Function
CM61 COMMAND CODE TITLE: EXTERNAL KEY FUNCTION FUNCTION: This command is used to activate and specify the function of the switch closure detection PGD(2)-U10 ADP when interfaced with external keys. PRECAUTION: None ASSIGNMENT PROCEDURE: KEY NUMBER DATA 61YY + DE (3 digits) (1-2 digits) DATA TABLE:...
Page 497 CM61 COMMAND CODE TITLE: EXTERNAL KEY FUNCTION : Default KEY NUMBER SETTING DATA RELATED COMMAND MEANING MEANING DATA MEANING Service operation by exter- XX Z XX: Key Group No. MJ/MN Alarm nal key (00-63) assigned by Clear key CM12 Y=66 Day/Night Mode Z : Circuit No.
Page 498: [Cm62] Tenants For Each Att Group
CM62 COMMAND CODE TITLE: TENANTS FOR EACH ATT GROUP FUNCTION: This command is used to assign which tenants are handled by each DESKCON Group. [8300R2] PRECAUTION: This command requires a reset by CM60 Y=90>0: 0 after data setting. Multiple tenants can be assigned to one ATT Group, but one tenant cannot be assigned to more than one ATT Group.
Page 499: [Cm63] Restriction Of Inter-Tenant Connection
CM63 COMMAND CODE TITLE: RESTRICTION OF INTER-TENANT CONNECTION FUNCTION: This command is used to define the restrictions on inter-tenant access. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT-A TENANT-B DATA + DE (2 digits) (2 digits) (1 digit) DATA TABLE: : Default TENANT SETTING DATA RELATED COMMAND...
Page 500: [Cm64] Automated Attendant, Tenant Number For Music On Hold, Number Of Queue Limit, Trunk Access Code For Mobility Access Mode, Isdn Alternating Routing
CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING FUNCTION: This command is used to define the answering system of the Automated Attendant feature and assign the Tenant Number for Music on Hold, the Number of Queue Limit, the Trunk access code for Mobility Access mode and the ISDN Alternating Routing.
Page 501 CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Tenant Number for Music 00-63 External Hold Tone Source CM48 Y=0...
Page 502 CM64 COMMAND CODE TITLE: AUTOMATED ATTENDANT, TENANT NUMBER FOR MUSIC ON HOLD, NUMBER OF QUEUE LIMIT, TRUNK ACCESS CODE FOR MOBILITY ACCESS MODE, ISDN ALTERNATING ROUTING : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Trunk access code for 00-63 X-XXXX Trunk Access Code...
Page 503: [Cm65] Services On Tenant Basis
CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS FUNCTION: This command is used to define the features available in each tenant. PRECAUTION: None ASSIGNMENT PROCEDURE: TENANT NUMBER DATA + DE 65YY (2 digits) (1 digit) DATA TABLE: : Default SETTING DATA RELATED TENANT COMMAND...
Page 504 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Number Display when 00-63 My Line number/name CM08>502 calling from Sub Line via Sub Line number/name CCIS/ Number Display through CCIS for SMDR NOTE: When setting Name Display to sub line, whether to display My Line number/name or sub line num- ber/name depends on CM08>502.
Page 505 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Call Forwarding type 00-63 Split Call Forwarding-All CM08>608 when an internal call Calls/Busy Line/No CME6 Y=04, 05 from station/attendant is Answer CM78 terminated via CCIS Call Forwarding-All Calls/ NOTE...
Page 506 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Multiline Terminal ring 00-63 See below CM15 Y=83, 84, 93 frequency CM35 Y=034, 164 CM76 Y=23 Y=40: 0 Y=40: 1 term term 70 (Elite Terminal)/ Ringer Tone term...
Page 507 CM65 COMMAND CODE TITLE: SERVICES ON TENANT BASIS : Default SETTING DATA RELATED TENANT COMMAND MEANING DATA MEANING Calling Number Display 00-63 To provide for each tenant when an Not provided incoming call is termi- nated to the Multiline Terminal with TAS Calling Number Display To provide for each tenant when an...
Page 508: [Cm67] Location Data Assignment
CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT FUNCTION: This command is used to assign the location data to the location number set by CM12 Y=39/50 (Peer- to-Peer connection by IP Station), CM8A Y=5000-5255: 173 (Peer-to-Peer connection via CCIS). The location number is used for administration of the location via IP network and can be assigned to each connection type or each location which is divided according to the network traffic.
Page 509 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT DATA TABLE: Y=00-08 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING CODEC list XX ZZ XX: Location Programmable CODEC List 0 CM42 between locations number (As per CM42>100-103, CM12 Y=39/50 CM8A Y=5000- (00-63)
Page 510 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING NOTE 3: The table below shows the default setting of the CODEC List. Priority CODEC Type Payload Size G.711* 40 ms. G.729a 40 ms.
Page 511 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING NOTE 7: CODEC and payload size that are available for each terminal is as following data. : Available –: Not available ( ): Usable payload size CODEC TERMINAL G.711...
Page 512 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of Service XX ZZ XX: Location X: PRECEDENCE 0-7 CM12 Y=39/50 (TOS) field Prece- number for control packet CM8A Y=5000- dence for IP Sta- (00-63) Z : PRECEDENCE 0-7...
Page 513 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING PAD data between XX ZZ XX: Location TT RR TT (Transmitter PAD): CM12 Y=39/50 locations number +: Gain CM8A Y=5000- (00-63) –: Loss 5255: 173...
Page 514 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Echo Canceller XX ZZ XX: Location Echo Canceller OFF CM12 Y=39/50 between locations number Echo Canceller ON CM8A Y=5000- (00-63) NONE Echo Canceller ON 5255: 173...
Page 515 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Diffserv Code XX ZZ XX: Location XX ZZ XX: 00-FE: DSCP of CM12 Y=39/50 Point (DSCP) of number control packet CM8A Y=5000- control packet and (00-63)
Page 516 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=10-26 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Time Zone setting Location number XXXXX Time Zone CM02 of each location (see the table below) NONE No Time Zone 2nd Data Time Zone A2345...
Page 517 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of tone for Location number Japan CM12 Y=39/50 each area/country North America for each location Australia A-law countries Hong Kong Malaysia Singapore Mexico...
Page 518 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of Service Location number PRECEDENCE 0 CM0B (TOS) field Prece- PRECEDENCE 1 Y=1XX>10 dence of control PRECEDENCE 2 CM12 Y=39/50 packet for IP Sta- PRECEDENCE 3 CM67 Y=15...
Page 519 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING FAX control infor- XX ZZ XX: Location Fixed list 1 (G.711) CM8A Y=5000- mation list to each number Fixed list 2 (G.726) 5255: 173 location (00-63)
Page 520 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Programmable list FAX Protocol Pat- Not detected the FAX CM67 Y=20 tern No. protocol NOTE Programmable list G.711 µ-law G.711 A-law Programmable list G.726 T.38 UDPTL...
Page 521 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Programmable list Maximum value 10 ms. CM67 Y=21/22/ of jitter buffer 23/24>08 Programmable list 300 ms. (10 ms. increments) Programmable list NONE 120 ms.
Page 522 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Programmable list T.38 version Version 0 (ASN.1 coding [8300R3] according to T.38 06- Programmable list 1998) Version 1 (1998 ASN.1 Programmable list syntax, org doc: 11-2000) Version 2 (ASN.1 coding...
Page 523 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=30, 31 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Daylight Saving Location number To operate with Daylight CM67 Y=10 time setting of each Saving time (+1 hour) CM0B Y=1XX>...
Page 524 CM67 COMMAND CODE TITLE: LOCATION DATA ASSIGNMENT Y=90-92 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Limit bandwidth XX ZZ XX: Location 00000 0 Kbps CM12 Y=39/50 between locations number CM8A (00-63) 65534 65534 Kbps Y=5000-5255: ZZ : Location NONE...
Page 525: [Cm71] Memory Allocation For System Speed Dialing
CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING FUNCTION: This command is used to allocate memory area for System Speed Dialing to tenants, attendants, Hot Line-Outside and Delayed Hotline-Outside station. PRECAUTION: System Speed Dialing has 300 memory locations system-wide; this is referred to as a “Memory Block”...
Page 526 CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING Limitation on Memory Slot Allocations • In a single-tenant system, Tenant No. 00 can be assigned a maximum of 300 memory slots. • Per Tenant: Maximum of 300 memory slots •...
Page 527 CM71 COMMAND CODE TITLE: MEMORY ALLOCATION FOR SYSTEM SPEED DIALING ASSIGNMENT PROCEDURE: KIND OF DATA + 71 + CALLING PARTY (6 digits) (2 digits) DATA TABLE: : Default KIND OF CALLING PARTY SETTING DATA MEANING DATA MEANING Tenant No. 00 XXX YYY XXX: Starting Memory Slot number in Block: 000-299...
Page 528: [Cm72] Stored Number For System Speed Dialing
CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING FUNCTION: This command is used to enter the stored number or character for System Speed Dialing feature into the memory allocated with CM71. PRECAUTION: When displaying the data, the access code corresponding to the Memory Slot number is indicated by the very first , and the stored number is indicated by the next .
Page 529 CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING 000-299 Memory Slot number XXXX YY...Y XXXX: Access Code (Maximum 4 digits) : Separator Mark YY...Y : Called Party Number (Maximum 26 digits) X-XXXXXXXX Station Number (Maximum 8 dig-...
Page 530 CM72 COMMAND CODE TITLE: STORED NUMBER FOR SYSTEM SPEED DIALING : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING 000-299 Memory Slot number XXX...X Calling Party Name Character by PCPro (Maximum 16 digits: 8 characters) (for Simplified Chinese) [8300R7] [Asia] NONE No data NOTE:...
Page 531: [Cm73] Memory Allocation For Station Speed Dialing
CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING FUNCTION: This command is used to allocate memory areas for Station Speed Dialing to individual stations. PRECAUTION: The allowed number of 10-Slot Memory Blocks per station number ranges from 1 to 10. ASSIGNMENT PROCEDURE: STATION NUMBER DATA...
Page 532 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING NOTE 2: An entry of “0342106” would allocate six (6) 10-Slot Memory Blocks, which would accom- modate sixty (60) Station Speed Dialing numbers. 1000- Slot Memory Block number 03 would be used, starting at 10-Slot Memory Block number 42, and ending at 10-Slot Memory Block number 47.
Page 533 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING Example: If the number of Speed Dial numbers is 10 for Station Number 300, 20 for Station Number 301, and 30 for Station Number 302, the memory areas assignment is as follows. Memory Start Block Station 1000-Slot Memory...
Page 534 CM73 COMMAND CODE TITLE: MEMORY ALLOCATION FOR STATION SPEED DIALING A memory area allocated by CM73 can be shared with several stations. Also, in the stations, which station can assign or change the data can be determined. Example: Station Number Assigned data Facility for Programming 0000003...
Page 535: [Cm74] Stored Number For Station Speed Dialing
CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING FUNCTION: This command is used to enter the stored number for Station Speed Dialing feature into the memory al- located with CM73. PRECAUTION: Data can only be changed when the access code is displayed. Enter the data in the following order; the new access code, comma, the called number, and .
Page 536 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING DATA TABLE: : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING XX YY Z XX: 1000-Slot Memory Block XX...X YY...Y XX...X: Access Code number (00-19) (Maximum 4 digits) YY: 10-Slot Memory Block : Separator Mark number (00-99) YY...Y : Called Party Number...
Page 537 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING XX YY Z XX: 1000-Slot Memory Block XXX...X Called Party Name Character by number (00-19) PCPro/CAT (Maximum 16 charac- YY: 10-Slot Memory Block ters) number (00-99) XXX...X...
Page 538 CM74 COMMAND CODE TITLE: STORED NUMBER FOR STATION SPEED DIALING : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING XX YY Z XX: 1000-Slot Memory Block XXX…X Called Party Name Character by number (00-19) PCPro (Maximum 16 digits: 8 YY: 10-Slot Memory Block characters) (for Simplified number (00-99)
Page 539: [Cm76] Digit Conversion On Did Call
CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL FUNCTION: This command is used to assign the data required for interpreting the dialed-in digits. PRECAUTION: Digit Conversion on DID call is available when CM35 Y=018 is set to 0. The first digit in the first data field must be assigned, in CM20 Y=0-3, as a station number 801-808. When entering data with characters, the following characters can be registered;...
Page 540 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING For Day Mode 000-999: Station number to be terminated CM10 Number Conver- NOTE 1 CM11 For Night Mode sion Block No. XXXXXXXX assigned by Change terminating system to:...
Page 541 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Terminating 000-999: Trunk Tenant 00 CM35 Trunk Tenant dur- Number Conver- Y=018 ing Day Mode sion Block No. Trunk Tenant 63 (for TAS) assigned by NONE...
Page 542 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Calling party 000-999: Available CM15 Y=134 number is used as Number Conver- Not available CM2A Y=15, the ID Code for sion Block No. 16, A0 Remote Access to assigned by...
Page 543 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Terminating Sta- 000-999: Station Tenant 00 tion Tenant for Number Conver- each DID number sion Block No. Station Tenant 63 during Mode B assigned by NONE Trunk Tenant...
Page 544 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Multiline Termi- 000-999: Ringer Tone Pattern 0 CM35 nal Ringer Tone Number Conver- Ringer Tone Pattern 1 Y=034, 164 Pattern on DID sion Block No.
Page 545 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Whether the call 000-999: Specified when reason of the incom- CM76 Y=34 terminating Number Conver- ing calls with no CLI is “Privacy” method is speci- sion Block No.
Page 546 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Specification of 000-999: To transfer to the VRS/another sta- CM51 Y=33 the call terminat- Number Conver- tion/Attendant Console (assigned by CM76 Y=35, ing method for sion Block No.
Page 547 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Interval of SLT/ 000-999: Ringing NOTE3 CM08>397 Multiline Termi- Number CM08>397 CM35 Y=033 nal ringing tone Conversion Special Ringing CM76 Y=34, for DID incoming Block No.
Page 548 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Multiline Termi- 000-999: Ringer Tone Pattern 0 CM65 Y=40 nal Ringer Tone Number Conver- Ringer Tone Pattern 1 CM76 Y=23, Pattern for DID sion Block No.
Page 549 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING VRS Waiting 000-999: To provide VRS Waiting Message CM35 Y=320 Message Number Conver- function (Announcement Service (for Day Mode) sion Block No. Start after Call Termination) [8300R7] assigned by...
Page 550 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING 1st VRS Waiting 000-999: VRS Waiting Message No. 00-63 CM35 Y=326 Message Number Conver- (for Mode A) sion Block No. [8300R7] assigned by NONE As per CM35 Y=326...
Page 551 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING VRS Waiting 000-999: To send only one time CM35 Y=333 Message Send Number Conver- As per CM35 Y=333 Pattern sion Block No. (for Night Mode) assigned by [8300R7]...
Page 552 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL : Default 2ND DATA 1ST DATA REMARKS MEANING DATA MEANING Multiple connec- 000-999: Play the message any time CM35 Y=339 tions of VRS Number Conver- As per CM35 Y=339 Waiting Message sion Block No.
Page 553 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL Data settings for Day/Night/A/B Mode Distinction of tenant An explanation of tenant selection method for Day/Night/A/B Mode change, when DID call ter- minates, is shown below as a tree diagram for system data registration. When station tenant for each DID number is assigned.
Page 554 CM76 COMMAND CODE TITLE: DIGIT CONVERSION ON DID CALL When station tenant for each DID number is not assigned. (CM76 Y=09 is not set) Terminating Trunk Tenant DAY/NIGHT/A/B Mode change 00~63 Trunk Tenant set by CM76 CM76 Y=18 Y=01 NONE Terminating Trunk Tenant 00~63 Trunk Tenant set by...
Page 555: [Cm77] Station/Trunk Route/Zt/Deskcon Name Assignment
CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT FUNCTION: This command is used to assign the name of each station, trunk route, Zone Transceiver, and DESKCON which is displayed on Multiline Terminal or Attendant Console. PRECAUTION: When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “...
Page 556 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT : Default STATION No./TRUNK SETTING DATA ROUTE NAME No./ REMARKS MEANING DATA MEANING ZT No./DESKCON No. Trunk Route Name 00-14, 16-63: Trunk Route XXX...X Character Code CM35 Y=003 assignment with Name number (Maximum 8 digits) character code (for assigned by...
Page 557 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT : Default STATION No./TRUNK SETTING DATA ROUTE NAME No./ REMARKS MEANING DATA MEANING ZT No./DESKCON No. DESKCON Name 0-7: DESKCON number Character assignment with assigned by CM10 (Maximum 16 char- character X..X acters) (for English) NONE...
Page 558 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT Character Code Table for English X: Upper digit Y: Lower digit ” & ’ < ¥ >  Example: To set “John”, do the following operation. 3-502 NWA-033623-001 Rev.8.1 91ch3005.fm JANUARY/31/2012...
Page 559 CM77 COMMAND CODE TITLE: STATION/TRUNK ROUTE/ZT/DESKCON NAME ASSIGNMENT Character Code Table for Russian X: Upper digit Y: Lower digit É Þ ü æ ä “ é Æ ö â ô ä ö ù μ à ò ÷ ü å û Õ...
Page 560: [Cm78] Destination Of Split Call Forwarding
CM78 COMMAND CODE TITLE: DESTINATION OF SPLIT CALL FORWARDING FUNCTION: This command is used to assign the called number of Split Call Forwarding. PRECAUTION: None ASSIGNMENT PROCEDURE: • To assign destination of Split Call Forwarding 1ST DATA 2ND DATA + DE (3 digits) (1-31 digits) •...
Page 561: [Cm81] Toll Restriction Pattern On Each Trunk Restriction Class
CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS FUNCTION: Toll call restriction is controlled by combinations of the toll office code dialed and assigned station trunk restriction class. With respect to toll call restriction, there are eight kinds of trunk restriction classes; Un- restricted, Non-Restricted-1, Non-Restricted-2, Semi-Restricted-1, Semi-Restricted-2, Restricted-1, Re- stricted-2, and Fully Restricted.
Page 562 CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS ASSIGNMENT PROCEDURE: The following command format is used to change the standard assignment data above to meet local re- quirements: TRUNK RESTRICTION DATA ST + 81YY CLASS (1 digit) (1 digit) DATA TABLE: TRUNK RESTRICTION...
Page 563 CM81 COMMAND CODE TITLE: TOLL RESTRICTION PATTERN ON EACH TRUNK RESTRICTION CLASS Examples: The following examples are typical installations within Melbourne, Australia. Unrestricted : No restrictions Non-Restricted-1 : 115, 116, 118, 001 and 010 codes are restricted. Non-Restricted-2 : 115, 116, 118, 02, 04, 06-09, 001-007, 009-011, 014, 016, 018, 019 and 054 codes are restricted.
Page 564: [Cm85] Maximum Number Of Sending Digits
CM85 COMMAND CODE TITLE: MAXIMUM NUMBER OF SENDING DIGITS FUNCTION: This command is used to define the maximum number of digits which can be dialed, after C.O. access, given a specific first digit. PRECAUTION: This command is effective when CM35 Y=076 is assigned. ASSIGNMENT PROCEDURE: MAXIMUM NUMBER AREA/OFFICE CODE...
Page 565 CM85 COMMAND CODE TITLE: MAXIMUM NUMBER OF SENDING DIGITS Example: The example given is typical for Australian applications and more specifically would apply to installations within Melbourne. NUMBER TO BE SENT TO C.O. LINE MAXIMUM NUMBER OF SENDING DIGIT NUMBER TO BE SENT TO C.O. LINE MAXIMUM NUMBER OF SENDING DIGIT NUMBER TO BE SENT TO C.O.
Page 566: [Cm8A] Lcr/Toll Restriction Development Table
CM8A COMMAND CODE TITLE: LCR/TOLL RESTRICTION DEVELOPMENT TABLE FUNCTION: This command is used to define the development tables used for Least Cost Routing (LCR) and Toll Re- striction (TR) features. PRECAUTION: To provide Outgoing Trunk Queuing (Trunk Queuing-Outgoing) in conjunction with Least Cost Rout- ing-3/6 Digit, you must set Route Pattern No.
Page 567: [Cm8A] Toll Restriction Development Table
CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE DATA TABLE: Toll Restriction Development Table CM35 Y=011, 076) : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 0000 Route Pattern No. 000 TR/LCR Pattern for 6- 00000 XXX 00 digit Toll Restriction XXX: TR Pattern 0255...
Page 568 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 3000 Date Pattern No. 0 Sunday 0000 Route Pattern No. 000 Monday 3003 Date Pattern No. 3 Tuesday 0255 Route Pattern No. 255 Wednesday (CM8A Y=0000-0255) No data...
Page 569 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 4000 Area Code Development Area Code 0000 Route Pattern No. 000 Pattern No. 0 (Maximum 8 digits) XX...XX 0255 Route Pattern No. 255 4004 Area Code Development (CM8A Y=0000-0255)
Page 570 CM8A COMMAND CODE TITLE: TOLL RESTRICTION DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 TR Pattern No. 000 Designation of Trunk Toll Restriction Pattern Restriction Pattern No. No. 00 5255 TR Pattern No. 255 Toll Restriction Pattern No.
Page 571: [Cm8A] Lcr Development Table
CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE LCR Development Table : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 0000 Route Pattern No. 000 Designation of next table 0000 Next Pattern No. 000 (Route Pattern No.) 0255 Route Pattern No. 255 0255 Next Pattern No.
Page 572 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 3000 Date Pattern No. 0 Sunday 0000 Route Pattern No. 000 Monday 3003 Date Pattern No. 3 Tuesday 0255 Route Pattern No. 255 Wednesday (CM8A Y=0000-0255) Thursday...
Page 573 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 4005 Area Code Development Area Code 3000 Date Pattern No. 0 Pattern No. 5 (Maximum 8 digits) XX...XX 3003 Date Pattern No. 3 4007 Area Code Development (CM8A Y=3000-3003)
Page 574 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Designation of Toll Toll Restriction Pattern Restriction Pattern No. No. 00 5255 LCR Pattern No. 255 Toll Restriction Pattern No.
Page 575 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Number of digit to be No digit deletion deleted from Area Code First one digit deletion 5255 LCR Pattern No.
Page 576 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Type of Called Party Unknown Number (for E.164) International number 5255 LCR Pattern No. 255 National number Not used Subscriber number Not used...
Page 577 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Call by Call Type of Network ID No. Network ID Plan [North America Only] 5255 LCR Pattern No. 255 NONE No data Call by Call...
Page 578 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Call by Call WATS Band Number WATS Band Number 5255 LCR Pattern No. 255 [North America Only] NONE No data Caller ID on outgoing...
Page 579 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Release timer for IPT 30 seconds (P2P CCIS) Point-to- 1 minute 5255 LCR Pattern No. 255 Multipoint connection (1 minute increments) 127 minutes Not Released...
Page 580 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Calling party number sent To send ISDN Subscriber from ISDN Trunk Number assigned by CM12 NOTE 1 5255 LCR Pattern No.
Page 581 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 5000 LCR Pattern No. 000 Sharing LCR Pattern No. To provide with alternative routing (As per CM8A Y=5000- 5255 LCR Pattern No. 255 5255>178) Not provided (As per CM8A Y=5000-...
Page 582 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING 8000 6-digit TR No. 00 Office Code (3 digits) Restricted Allowed 8049 6-digit TR No. 49 8050 6-digit Prefix No. 00 Office Code (3 digits) Restricted Allowed 8099...
Page 583 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE NOTE 3: Calling party number sent from SIP Trunk depends on setting data as shown below. • Caller Number Information : Default CMBA Y=44 CM8A REMARKS (Caller ID (Caller ID (Caller ID (Caller ID (Not Y=5XXX>176 conversion...
Page 584 CM8A COMMAND CODE TITLE: LCR DEVELOPMENT TABLE • For Tandem Connection : Default CMBA Y=44 INCOMING REMARKS (Caller ID (Caller ID (Caller ID Caller ID (Not CALLING conversion conversion conversion conversion provided) mode 0) mode 1) mode 2) mode 3) Not informed Representa- Representa-...
Page 585: [Cm8B] Toll Restriction Pattern Number For Call Forwarding-Outside
CM8B COMMAND CODE TITLE: TOLL RESTRICTION PATTERN NUMBER FOR CALL FORWARDING-OUTSIDE FUNCTION: This command is used to restrict Call Forwarding-Outside (including Call Forwarding-All Calls/-No Answer/-Busy Line/-PS Out of Zone/-Logout (IP Station)) according to the forwarding destination num- [8300R6] ber. PRECAUTION: None ASSIGNMENT PROCEDURE: FORWARDING DESTINATION NUMBER/...
Page 586: [Cm90] Multiline Terminal/Deskcon/Add-On Module Key Assignment
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL/DESKCON/ADD-ON MODULE KEY ASSIGNMENT FUNCTION: This command is used to assign functions to programmable keys on a Multiline Terminal, DESKCON or Add-on Module. PRECAUTION: “My Line” must always be assigned to any key except key No. 00 on each Multiline Terminal or Add-on Module.
Page 587: [Cm90] Multiline Terminal Key Assignment
CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT ASSIGNMENT PROCEDURE: Multiline Terminal MY LINE DATA + 90YY + NUMBER NUMBER (1-8 digits) (1-8 digits) (01-24, 90-99) ORIGINAL STATION COPIED STATION + 9009 + + DE NUMBER NUMBER (1-8 digits) (1-8 digits) DATA + 9010 + + DE...
Page 588 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT DATA TABLE: Multiline Terminal SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions Station number CM10 • My Line number (FX-FXXXXXXXX) CM11 XXXXXXXX • Multiline number (Ordinary Station) • Multiline number (assigned by CM11) X: 0-9, A (*), B (#) A000...
Page 589 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions AA01 Loop Line number for Multiline Terminal CM11 Attendant Position CM15 Y=071 AA05 CM12 Y=03 AA11 AAX Z X: Multiline Terminal Attendant Position AA15 No.
Page 590 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX 018: Call Forwarding-Destination Set CM15 Y=015 (FDDS) 019: Call Forwarding-Destination Cancel (FDDC) 020: Call Pickup-Group (PICK) CM16 021: Call Pickup-Direct (DPICK) CM15 Y=014 022: Do Not Disturb Set/Reset (DND) CM15 Y=019...
Page 591 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX Service access code 040: Message Waiting Lamp Set (MWS) CM15 Y=024 041: Message Waiting Lamp Reset (MWR) 044: ACD/UCD Busy out (UCDB) 046: Call Hold (CHLD) CM15 Y=001 047: TAS Answer A (TASA)
Page 592 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX A25: Call Waiting (CW) Service access code A26: LCR Group 0 A27: LCR Group 1 A28: LCR Group 2 A46: Call History screen start Message A70: Malicious Call Trace...
Page 593 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F0XXX B51: Connection between Soft Phone and NOTE B54: Restriction of additional participants to conference Set/Cancel [8300R2] B56: Mobility Access Mode Set/Cancel CM20 Y=0-3: NOTE A256, A257...
Page 594 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F1XXX 011: Feature 012: (CNF) Conf [8300R2] 013: Save & Repeat (2) (S&R2) 014: Save & Repeat (3) (S&R3) 015: (RECALL) CM15 Y=007 Recall...
Page 595 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F1XXX 070: Call Record (REC) For Front Desk 071: Print Out (PRINT) Terminal func- 072: Group (GROUP) tions CM15 073: Details (DETAL) Y=062 074: Set (SET) 075: Reset (RESET)
Page 596 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F12XX 01: Trunk Group 01 Busy Lamp (TGB01) CM30 Y=09 62: Trunk Group 62 Busy Lamp (TGB62) 70: Internal Zone Paging Group 0 (PG0) CM56 Y=00-07 CM15 Y=049 77: Internal Zone Paging Group 7 (PG7)
Page 597 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F40XX 00: TAS Answer on Tenant 00 (ANS00) CM30 01: TAS Answer on Tenant 01 (ANS01) Y=00, 02, 03 Answer CM12 Y=04 CM57 Y=30 63: TAS Answer on Tenant 63 (ANS63)
Page 598 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F5026 Record (Voice Mail Live Record-CCIS) CM08>578 [8300R5] F5027 End (Voice Mail Live Record-CCIS) CM08>578 [8300R5] F5028 Play (Voice Mail Live Record-CCIS) CM08>675 [8300R5] F5030...
Page 599 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Functions F7XXZ Relay Control Function Key CM44 Y=00: : Relay Group No. (00-31) 1500 assigned by CM44 : Circuit No. (0-3) assigned by CM44 312, 313: External Relay Interface of CPU blade...
Page 600 CM90 COMMAND CODE TITLE: MULTILINE TERMINAL KEY ASSIGNMENT SETTING DATA RELATED COMMAND MEANING DATA MEANING Key setting of program- – Same as CM90 Y=00 CM04 Y=00>02 mable pattern 1 NOTE: Be sure to set the Key No. “F5099” (My Line) to any key on the Multiline Terminal or the Add-on Module when programmable pattern 1 is assigned.
Page 601: [Cm90] Deskcon Key Assignment
CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT SN716 DESKCON Call Selection/Function Key Assignment: DESKCON DESKCON SETTING + , + + 90YY + NUMBER KEY NUMBER DATA (E000-E007) (07-24, 90-97) (5 digits) Multi-Function Key Assignment: MULTI- SETTING FUNCTION + , + 90YY EXX Y ST +...
Page 602 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT SN716 DESKCON • DESKCON Call Selection Key STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6000 C.O. Incoming Call 0 (LDN0) LDN0 CM35 Functions NOTE 2 Y=015 [8300R2] F6007 C.O. Incoming Call 7 (LDN7) NOTE 1 F6010 Call Termination from FX Line 0...
Page 603 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6054 Priority Call 0 (PRI0) CM15 Functions Y=017 [8300R2] CM08>250, NOTE 1 CM20 Y=0-3: A088 F6055 Priority Call 1 (PRI1) CM15 Y=018 CM08>251, CM20 Y=0-3: A089...
Page 604 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT • DESKCON Function Key STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6100 Room Cutoff (RC) For Hotel DESKCON Functions • Use the ANSWER key as the SET key for F6101 Message Waiting (MW) [8300R2]...
Page 605 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6112 Out pulse (PB signal) short CM35 Functions (SPB) Y=026 [8300R2] F6113 Out pulse (PB signal) long CM41 (LPB) Y=0>14 F6120 Malicious Call Trace CM15 [Australia Only] Y=211...
Page 606 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT STANDARD SETTING RELATED FUNCTION REMARKS DATA COMMAND MEANING SETTING Setting of F6240 Loop 1 (LOOP 1) LOOP 1 Functions [8300R2] F6245 Loop 6 (LOOP 6) LOOP 6 NOTE 2 F6252 Answer (ANSWER) ANSWER F6253 Release (RELEASE) RELEASE...
Page 607 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT NOTE 2: The table below shows the default settings of programmable keys (key No. 07-97) which are set when DESKCON is set by CM10. DEFAULT SETTINGS DEFAULT SETTINGS KEY No. KEY No. SETTING SETTING MEANING MEANING...
Page 608 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT • DESKCON Multi-Function Key No. 01-04 CM60 Y=17 DESKCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND Idle state F6100 Room Cutoff [8300R2] (RCOF) F6102 Do Not Disturb (DND) F6104 Reset (RESET) F6110 Mode (MODE) F6111 Programming (PROG)
Page 609 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT DESKCON SETTING RELATED STATUS MEANING FUNCTION REMARKS DATA COMMAND When the called F6108 Do Not Disturb station is in DND Override (DDOV) [8300R2] When accessing F6100 Room Cutoff For Hotel DESKCON Hotel features (RCOF) [8300R2] NOTE:...
Page 610 CM90 COMMAND CODE TITLE: DESKCON KEY ASSIGNMENT NOTE 4: If no data is set, the Multi-Function keys (key No. 01-09) are automatically set by default as shown below. • Idle State MODE: Mode PROG: Programming 1:23 PM WED 05 OCT 2011 MODE PROG •...
Page 611: [Cm90] Add-On Module Key Assignment
CM90 COMMAND CODE TITLE: ADD-ON MODULE KEY ASSIGNMENT Add-On Module MY LINE KEY NUMBER DATA + 90YY + NUMBER (1-8 digits) (30-89) (1-8 digits) KEY NUMBER DATA + 9010 + + DE (1-8 digits) (30-89) SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Func-...
Page 612 CM90 COMMAND CODE TITLE: ADD-ON MODULE KEY ASSIGNMENT : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Setting of Func- B000 Dial Intercom number CM11 tions CM56 Y=12 B900 B001 B901 B024 B924 D000 Trunk number CM10 CM30 Y=18 D511 F11XX CM73 00-99: Station Speed Dialing 00-99...
Page 613: [Cm93] Prime Line
CM93 COMMAND CODE TITLE: PRIME LINE FUNCTION: This command is used to assign the prime line to a station line or a trunk line on a Multiline Terminal. The prime line is the line seized when the Multiline Terminal user goes off-hook or presses the speaker key.
Page 614: [Cm94] Multiline Terminal One-Touch Memory
CM94 COMMAND CODE TITLE: MULTILINE TERMINAL ONE-TOUCH MEMORY FUNCTION: This command is used to assign memory for the storage of numbers accessed by the one-touch keys on a Multiline Terminal. PRECAUTION: Do not duplicate the same memory area for CM73 and CM94 usually. However, when Dial by Name feature using one-touch keys or BLF on Multiline Terminal line key feature are provided, the same mem- ory areas must be specified by CM73 and CM94.
Page 615: [Cm96] Dss Console Number
CM96 COMMAND CODE TITLE: DSS CONSOLE NUMBER FUNCTION: This command is used to assign a DSS Console to a station, Multiline Terminal or Attendant Console. PRECAUTION: None ASSIGNMENT PROCEDURE: DSS CONSOLE DATA + 96 + NUMBER (1-8 digits) (2 digits) DATA TABLE: : Default SETTING DATA...
Page 616: [Cm97] Dss Console Key Assignment
CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT FUNCTION: This command is used to assign the station numbers and trunk numbers to the keys on each DSS Con- sole. PRECAUTION: None ASSIGNMENT PROCEDURE: DSS CONSOLE DSS KEY DATA + DE NUMBER NUMBER (1-8 digits)
Page 617 CM97 COMMAND CODE TITLE: DSS CONSOLE KEY ASSIGNMENT DATA TABLE: SETTING DATA RELATED CONSOLE COMMAND DATA MEANING NUMBER NUMBER Station number CM10 CM11 XXXXXXXX DXXX Trunk number CM10 CM10 (XXX: 000-511) CM30 Y=00: Y=02, 03, 18 E100- F13XX CM08>244 E131 00: Day/Night Mode Change by Tenant 00 CM08>245 63: Day/Night Mode Change by Tenant 63...
Page 618: [Cm98] Add-On Module Number
CM98 COMMAND CODE TITLE: ADD-ON MODULE NUMBER FUNCTION: This command is used to assign the Add-on Module to the My Line number of a Multiline Terminal. PRECAUTION: One Add-on Module number can be assigned for each My Line number of a Multiline Terminal. This command should be performed before the data assignment of CM90.
Page 619: [Cm9A] Multiline Terminal Soft Key Assignment
CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT FUNCTION: This command is used to assign functions for the Soft Key on a Multiline Terminal. PRECAUTION: When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “ # $ % & ’ ( ) + , ; < = >...
Page 620 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT DATA TABLE: : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-11) F5002 Scroll key to change the Key function for 00: Idle State Soft key indication each Pattern...
Page 621 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-11) XX...XXX Soft Key name indicated Key name for 00: Idle State on LCD (2-12 characters) Character Code each Pattern...
Page 622 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-11) XX...XXX Soft Key name indicated Key name for 00: Idle State on LCD (2-12 characters) Character Code each Pattern...
Page 623 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of Soft aa bb aa : Status Number (00-11) XX...XXX Soft Key name indicated Key name for 00: Idle State on LCD (Maximum 6 characters;...
Page 624 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT Default Data of CM9A (Pattern No. 3) 1ST DATA of 2ND DATA INDICATION STATUS MEANING Y=03 of Y=03 (Y=13) 0000 Idle F1017 MIC ON/OFF 0001 F5014 Dial By Name for System SYS.
Page 625 CM9A COMMAND CODE TITLE: MULTILINE TERMINAL SOFT KEY ASSIGNMENT Default Data of CM9A (Pattern No. 3) 1ST DATA of 2ND DATA INDICATION STATUS MEANING Y=03 of Y=03 (Y=13) 0600 When called party is F0004 Call Back Set busy (Holding no call) 0601 F0A25 Call Waiting Set...
Page 626: [Cm9B] Event Occurrence Notice Button Assignment
CM9B COMMAND CODE TITLE: EVENT OCCURRENCE NOTICE BUTTON ASSIGNMENT FUNCTION: This command is used to provide the event occurrence notice button. When the offices with CCIS via IPT (P2P CCIS) connection SIP trunk connection are disconnected due to a fault occurrence, the link down can be notified to the Multiline Terminals that are connected to the offices.
Page 627: [Cm9C] Desi-Less Lcd
CM9C COMMAND CODE TITLE: DESI-LESS LCD FUNCTION: This command is used to set characters displayed on DESI-less LCD of DT300/DT700 Series. [8300R2] PRECAUTION: This data setting is valid by resetting DT300/DT700 Series or executing CM12 Y=29. ASSIGNMENT PROCEDURE: BLOCK NUMBER DATA + 9CYY + + DE...
Page 628 CM9C COMMAND CODE TITLE: DESI-LESS LCD : Default 1ST DATA SETTING DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Function Name Block number XXX...X Character (Maximum 4 assignment with characters; 8 digits) character (for Tradi- NONE No data tional Chinese) [8300R7] [Asia] NOTE NOTE:...
Page 629: [Cma7] Ccis Channel/Ip Trunk/Sip Trunk Data
CMA7 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 1 FUNCTION: This command is used to assign the various data to each Common Channel Handler (CCH), IP Trunk and SIP Trunk provided. PRECAUTION: When setting the IPT (P2P CCIS) No. with this command, be sure to set the first data to “00”. ASSIGNMENT PROCEDURE: DATA A7YY...
Page 630: [Cma8] Ccis Channel/Ip Trunk/Sip Trunk Data
CMA7 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Destination Point Code (DPC) 00001 Destination Point Code 16367 NONE No data NOTE 1: For Point-to-Point connection to SIP trunk (CMA7 Y=46: 1), set this data to SIP trunk No. of SIP trunk that is used for DPC of SIP server assigned by CMA7 Y=02.
Page 631 CMA7 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ACM signal waiting timer after send- 2 seconds ing IAI signal when originating calls (2 seconds increments) via CCIS 28 seconds 6 seconds SIP trunk ringing/answer response timer when time-out occurs alternate...
Page 632 CMA7 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING DiffServ code point setting for IPT 00-3F DiffServ code point CM35 Y=161 (P2P CCIS) control packet NONE No data CMA7 Y=44 IPT (P2P CCIS) RESET NOTE 1: Set this data when the router provides DiffServ QoS, if required.
Page 633 CMA7 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 1 : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Own Office number (for 5 digits) 00000 Office Code CMA7 Y=06 [8300R3.5] 99999 NONE No data NOTE: Do not assign CMA7 Y=06 and CMA7 Y=82 simultaneously. The setting of CMA7 Y=82 has a priority if these two commands are assigned simultaneously.
Page 634 CMA8 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 2 FUNCTION: This command is used to assign a destination office for a message to be transferred (e.g. service infor- mation) and the Common Channel Handler (CCH), IP trunk and SIP trunk which accommodate the mes- sage.
Page 635 CMA8 COMMAND CODE TITLE: CCIS CHANNEL/IP TRUNK/SIP TRUNK DATA 2 NOTE 3: Programming procedure of CMA8 Y=1 is as follows. - For IPT (P2P CCIS), set this data IP address of destination IPT (VoIP address of destina- tion office). - For Point-to-Point connection to SIP trunk (CMA7 Y=46: 1), this data is not needed to as- signed.
Page 636 CMA9 COMMAND CODE TITLE: BLADE RESET ISDN (PRI) D-CHANNEL ASSIGNMENT FUNCTION: This command is used to assign the various data to each D-Channel for ISDN-Primary Rate Interface. PRECAUTION: This command requires the blade reset after data setting. ASSIGNMENT PROCEDURE: D-CHANNEL No. DATA + DE A9YY...
Page 637: [Cmaa] Dti/Brt/Prt/Cct Blade Functions
CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT BLADE FUNCTIONS FUNCTION: This command is used to assign the functions to the DTI, BRT, PRT, and CCT blade. PRECAUTION: After setting CMAA Y=00-02, 06, 09, 19-21, 25, the blade reset is required. ASSIGNMENT PROCEDURE: TRUNK BLADE NUMBER DATA AAYY...
Page 638 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT BLADE FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Trunk Make Busy for DTI (E1 Available CM05 Y=1 2 Mbps) Not available [8300R3.5] NOTE: For a DTI (E1 2 Mbps) blade that is made busy, both Incoming/Outgoing calls are restricted. CM05 Y=1 ISDN Protocol Type for PRT (T1 Australia...
Page 639 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT BLADE FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING ISDN Protocol Type Australia CM05 Y=1 for BRT New Zealand AT&T (#4, #5 ESS) BLADE RESET NTI (DMS 100, 250) Australia ETSI ETSI Standard (Brazil, Columbia, Indonesia, UAE) ITU-T Standard (Thailand)
Page 640 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT BLADE FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Type of PRT/CCT E1 (2 Mbps) CM05 Y=1 T1 (1.5 Mbps) Providing PRT (T1 1.5 Mbps/E1 To provide CM05 Y=1 2 Mbps)/BRT blade with ISDN Not provided CM42>69, 70 Advice of Charge (AOC)
Page 641 CMAA COMMAND CODE TITLE: DTI/BRT/PRT/CCT BLADE FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Local loopback setting for BRT/ Local Loop Back (for BRT) CM05 Y=1 PRT (T1 1.5 Mbps/E1 2 Mbps) Remote Loop Back for PRT (FIFO (For test) unavailable) Payload Loop Back (for PRT)
Page 642: [Cmac] Isdn Functions
CMAC COMMAND CODE TITLE: ISDN FUNCTIONS FUNCTION: This command is used to assign the functions to the BRT blade. PRECAUTION: None ASSIGNMENT PROCEDURE: ISDN CIRCUIT No. DATA ST + ACYY D-CHANNEL No. (0-3) (1-8 digits) (00-31) ISDN TRUNK BLADE No. CIRCUIT No.
Page 643 CMAC COMMAND CODE TITLE: ISDN FUNCTIONS : Default SETTING DATA RELATED COMMAND MEANING DATA MEANING Type of power supply for ISDN tele- Power supply from the system phone Local power supply BLADE RESET SPID (Service Profile ID) for each B XXXX ZZZZ XXXX: ISDN Subscriber No.
Page 644: [Cmad] Zt/Sip Converter Calling Area/Pad Data Assignment
40 dB (Faint) from PS to ZT 20 dB (Average) [Latin America Only] 0 dB (Strong) NOTE NOTE: Follow the default setting. When you change the data of CMAD Y=04/05/06, contact NEC. Continued on next page 3-588 NWA-033623-001 Rev.8.1 91ch3007.fm JANUARY/31/2012...
Page 645 CMAD COMMAND CODE TITLE: ZT/SIP CONVERTER CALLING AREA/PAD DATA ASSIGNMENT : Default ZT/SIP SETTING DATA MEANING CONVERTER DATA MEANING UNIT number of SIP Converter 000-127 Unit No. 01 [8300R7] Unit No. 50 RESET NONE Unit No. 01 NOTE: When a standard SIP terminal is accommodated to Remote Unit, set the Unit number by this com- mand.
Page 646: [Cmae] Zt Operation Data Assignment
CMAE COMMAND CODE TITLE: ZT OPERATION DATA ASSIGNMENT FUNCTION: This command is used to assign the ZT operation data. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA SETTING DATA + DE AEYY (2 digits) (1-12 digits) DATA TABLE: : Default 1ST DATA SETTING DATA DATA MEANING...
Page 647 CMAE COMMAND CODE TITLE: ZT OPERATION DATA ASSIGNMENT : Default 1ST DATA SETTING DATA MEANING DATA MEANING DATA MEANING ZT Operation Mode 00-31 Calling Area No. Crowded Mode Normal Mode BLADE RESET Width of Calling 00-31 Calling Area No. Wide Area Narrow BLADE RESET...
Page 648 CMAE COMMAND CODE TITLE: ZT OPERATION DATA ASSIGNMENT : Default 1ST DATA SETTING DATA MEANING DATA MEANING DATA MEANING Network ID for Network ID assign- 00000-65534 Network ID Roaming Service ment NONE No data [For PCS] [8300R2] BLADE RESET NOTE 6 NOTE 1: Be sure to set from the 1st digit to last digit (10 digits).
Page 649: [Cmaf] Visitor Ps Data Assignment
CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT FUNCTION: This command is used to assign the Visitor PS data for Roaming. [8300R2] PRECAUTION: This command is effective only for North America/Latin America. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE AFYYY (1-4 digits) (1-4 digits)
Page 650 CMAF COMMAND CODE TITLE: VISITOR PS DATA ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Route Selection Pattern Trunk Restriction Class Route Selection Pattern 0 number for Trunk sent from Home PBX Data clear Restriction Class sent 01: Unrestricted (RCA) NONE No data...
Page 651: [Cmb0] Peg Count
CMB0 COMMAND CODE TITLE: PEG COUNT FUNCTION: This command allows accumulated data of use for maintenance purposes to be read from the system PEG counter. Data can be cleared after reading. PRECAUTION: When the system is reset, the contents in the memories of the PEG counter are all cleared. ASSIGNMENT PROCEDURE: •...
Page 652 CMB0 COMMAND CODE TITLE: PEG COUNT • To clear each ZT PEG COUNT data 1ST DATA + DE (4 digits) • To clear all ZT PEG COUNT data + DE DE + 9999 • To display 1ST DATA ST + + DE (4 digits) 3-596...
Page 653 CMB0 COMMAND CODE TITLE: PEG COUNT DATA TABLE: TRUNK STATUS DATA SETTING DATA DATA MEANING Number of outgoing trunk seizure-Trunk Route No. 00-63 Number of tandem connections established Number of times a busy station was encountered Number of all types of calls to Attendant Console [8300R2] Number of connections giving Dial Tone Number of station-to-station connections established...
Page 654 CMB0 COMMAND CODE TITLE: PEG COUNT TRUNK STATUS DATA SETTING DATA DATA MEANING Number of hookings in Mobility Access connection Number of outgoing calls of ISDN Alternative Routing in Remote Unit survival mode Number of Call Completion to Busy Subscriber (CCBS) set from calling party [For EU] Number of Call Completion to Busy Subscriber (CCBS) set...
Page 655 CMB0 COMMAND CODE TITLE: PEG COUNT TRUNK STATUS DATA SETTING DATA DATA MEANING Number of unanswered incoming calls-Trunk Route 00-63 Number of register connection on trunk call-Trunk Route 00- Number of conference calls (Three/Four way Calling) Number of failures cased by all conference trunks (For three way Calling) being busy Number of transferred incoming calls to Attendant Console or predetermined station, by Call Forwarding-No Answer...
Page 656 CMB0 COMMAND CODE TITLE: PEG COUNT : Default 1ST DATA 2ND DATA DATA MEANING DATA MEANING Setting of PEG COUNT Start MM DD HH mm MM: Month (01-12) Setting of Time DD : Day (01-31) duration for HH : Hour (00-23) Setting of PEG COUNT End measuring mm : Minute (00-59)
Page 657 CMB0 COMMAND CODE TITLE: PEG COUNT NOTE 2: The meaning of the data displayed is as shown below. 0: Not started 1: Under measuring 2: Finished After turning power on or after a system reset, the system starts the PEG COUNT, if the PEG COUNT start time has not been set.
Page 658: [Cmb1] Traffic Measurement
CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT FUNCTION: This command is used to measure traffic data of outgoing/incoming trunk calls and to display the data on CAT or PCPro. PRECAUTION: When the system is reset, all commands of CMB1 are initialized. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA...
Page 659 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of traffic Setting End Time for MMDDHHmm MM: Month (01-12) measurement condition Traffic Measurement DD : Day (01-31) HH : Hour (00-23) mm : Minute (00-59) NONE No data...
Page 660 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT 1ST DATA 2ND DATA TRAFFIC MEANING DATA MEANING MEANING DATA Display incoming trunk XXXZ XXX: Trunk No. (000-511) XXXX Incoming trunk traffic data traffic data : Record No. (0-6) (4 digits) X.XXX erl (Ex.) 0125  0.125erl Display outgoing trunk XXXZ XXX: Trunk No.
Page 661 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Setting of traffic mea- Traffic Measurement No Measurement surement for ZT Mode of ZT Hourly Measurement Setting Start Time for MMDDHH MM: Month (01-12) Traffic Measurement DD : Day (01-31) of ZT...
Page 662 CMB1 COMMAND CODE TITLE: TRAFFIC MEASUREMENT 2ND DATA 1ST DATA TRAFFIC MEANING DATA MEANING MEANING DATA Display traffic data of XXXZZ XXX: ZT No. (000-127) XXXX Traffic data X.XXX erl ZZ : Time Zone No. (00-24) (4 digits) (Ex.) 1223 1.223 erl NOTE 1: Meaning of the 1st data and 2nd data is as follows.
Page 663: [Cmb3] Ucd Peg Count
CMB3 COMMAND CODE TITLE: UCD PEG COUNT FUNCTION: This command allows accumulated traffic data related to the UCD Group to be read from the system. PRECAUTION: When the system is reset, the contents in the memories of the PEG counter are all cleared. ASSIGNMENT PROCEDURE: •...
Page 664 CMB3 COMMAND CODE TITLE: UCD PEG COUNT SETTING DATA TRUNK STATUS MEANING DATA MEANING DATA Number of call waiting calls for prede- XX: UCD Group (00-15) [8300R5 or before] termined time (CM41 Y=0>16) in queu- ing mode on UCD Group : UCD Group (00-99) NOTE 2 [8300R6 or later]...
Page 665: [Cmb4] Peg Count Of Ip Network
CMB4 COMMAND CODE TITLE: PEG COUNT OF IP NETWORK FUNCTION: This command allows accumulated traffic data for Bandwidth Control between location groups on IP network to be read from the system PEG counter. Data can be cleared after reading. PRECAUTION: When the system is reset, the contents in the memories of the PEG counter are all cleared.
Page 666 CMB4 COMMAND CODE TITLE: PEG COUNT OF IP NETWORK DATA TABLE: 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING CM67 Number of times that XXZZ XX: Location 00000 Counter data display traffic exceeded the number of NOTE 1 limit bandwidth group to 49999...
Page 667: [Cmba] Sip Profile Data
CMBA COMMAND CODE TITLE: SIP PROFILE DATA FUNCTION: This command is used to assign the various profile data for SIP Trunk. PRECAUTION: Profile No. for control packet is assigned by CMA7 Y=71. When entering data with characters, the following characters can be registered; Alphabet upper case (A-Z), alphabet lower case (a-z), numeric (0-9), symbol (! “...
Page 668 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING TOS/Diffserv Prece- Profile number TOS/Diffserv Prece- CM35 Y=161 dence for SIP trunk for control dence CMA7 Y=71 control packet packet CMBA Y=04 NONE No data...
Page 669 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Voice encoding selec- Profile number Programmable List CM8A tion precedence for SIP for control Standard Mode 2 Y=5XXX: Standard Mode 3 trunk packet Tone Quality Mode 2...
Page 670 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Payload size for SIP Profile number 20 ms. CM8A trunk for control 30 ms. Y=5XXX: packet 40 ms. RESET CMA7 Y=71 NOTE 1: This data is not available when CMBA Y=21 is set to default data.
Page 671 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING SIP server IP Address Profile number aaabbb SIP server IP Address CMA7 Y=71 for control cccddd aaa : 000-255 RESET packet bbb: 000-255 ccc : 000-255...
Page 672 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Caller ID conversion on Profile number Caller ID conversion CM8A SIP trunk call for control packet mode 0 Y=5XXX> Caller ID conversion RESET mode 1 CMA7 Y=71...
Page 673 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of SIP AoR Profile number XXX...X SIP AoR user name CMA7 Y=71 user name with charac- for control packet (24 digits, 12 charac- CMBA Y=45, ter code (Middle 12...
Page 674 CMBA COMMAND CODE TITLE: SIP PROFILE DATA Y=52-99 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING DTMF out-band mode Profile number Out-band mode (with CMA7 Y=71 for SIP trunk for control packet RFC2833) NONE In-band mode (Voice RESET pass through) Setting of SIP AoR...
Page 675 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Session Timer method Profile number UPDATE CMA7 Y=71 for control packet INVITE CMBA RESET Auto Y=29, 83, 88 NOTE 1: When the second data is set to 3, the session timer method is decided by the receiving message from the communicated terminal.
Page 676 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X User name CMA7 Y=71 tion user name when for control packet (24 digits, 12 charac- CMBA Y=72, registering to/sending ters fixed)
Page 677 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of SIP trunk Profile number XXX...X Domain name CMA7 Y=71 domain name for SIP- for control packet (Maximum 32 digits) CMBA URI with character NONE...
Page 678 Set the second data to NONE for Point-to-Multipoint connection (when CMA7 Y=46 is set to “0”). NOTE 5: When SIP-URI is “1234@nec.com”, the part of “nec.com” is set by this command. When NONE is set by CMBA Y=77, 78 and 79, IP address such as “1234@192.168.1.1” is used.
Page 679 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Type of Routing Profile number Strict routing CMA7 Y=71 [North America for control packet Loose routing Only] [8300R4] RESET IP address used for IP address of SIP CMA7 Y=71 SIP-URI...
Page 680 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Timer of response Profile number No Time-out CMA7 Y=71 for control packet 1-2 seconds waiting for calling (INVITE transaction 59-60 seconds time-out timer) (1 second increment) 32 seconds...
Page 681 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the display Profile number Display name: CMA7 Y=71 name/user name for for control packet SIP AoR User CMBA Y=44-47, 54 From Header Description following...
Page 682 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the Fully Profile number XXX...X Domain name CMA7 Y=71 Qualified Domain for control packet (24 digits, 12 charac- CMBA Y=93, Name (FQDN) for SIP ters fixed)
Page 683 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the Fully Profile number XXX...X Domain name CMA7 Y=71 Qualified Domain for control packet (16 digits, 8 charac- CMBA Name (FQDN) for SIP ters fixed)
Page 684 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of the Unit Profile number Unit No. 01 CMA7 Y=71 number to query the for control packet NONE No data CM0B DNS server Y=1XX>60,...
Page 685 CMBA COMMAND CODE TITLE: SIP PROFILE DATA Y=100-157 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X User name CMA7 Y=71 tion user name when for control packet (24 digits, 12 charac- CMBA Y=72, registering to/sending ters fixed)
Page 686 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting of Authentica- Profile number XXX...X Password CMA7 Y=71 tion password when for control packet (16 digits, 8 charac- CMBA Y=74, registering to/sending ters fixed) 75, 102...
Page 687 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Perform re-registration Profile number To provide uncondi- CMA7 Y=71 unconditionally when for control packet tionally receiving “authentica- To provide only when tion error”...
Page 688 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Send a signal to require Profile number To provide CMA7 Y=71 a deletion during a for control packet Not provided reset setting registra- tion RESET...
Page 689 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Resending period of Profile number 320 sec. CMA7 Y=71 REGISTER after REG- for control packet 60 sec. ISTER sending NG [North America Only] [8300R4]...
Page 690 When setting the second data to NONE, the changeover to the FAX communication from the voice communication using G.729a is not effective. NOTE 3: When detecting FAX communication, G.711 µ-law (NEC’s proprietary procedure, enhanced pay- load type) as CODEC type is recommended. Continued on next page 3-634 NWA-033623-001 Rev.8.1...
Page 691 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Setting payload size for Profile number 20 ms. CMA7 Y=71 FAX communication for control packet 30 ms. CMBA Y=22 from SIP trunk 40 ms.
Page 692 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Selection of reference Profile number Get Caller ID from CMA7 Y=71 to Caller ID for control packet the Username field if [8300R2] the Displayname field of the From header of...
Page 693 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Selection of contact Profile number Ignore “Contact header” CMA7 Y=71 address after SIP 407- for control of SIP 407- status status packet Contact to address of...
Page 694 CMBA COMMAND CODE TITLE: SIP PROFILE DATA : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Calling party number Profile number Available CMA7 Y=71 delimited depending on for control Not available semicolon of From packet header [8300R4] Handling of the Available...
Page 695: [Cmbc] Presence Service, Sip Converter, Greeting Process Of
CMBC COMMAND CODE TITLE: PRESENCE SERVICE, SIP CONVERTER, GREETING PROCESS OF SP350 FUNCTION: This command is used to assign the data to control Presence Service, SIP Converter or greeting process of SP350. [8300R3.5] ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA ST + BCYY + DE (3/4 digits) (1-15 digits)
Page 696 CMBC COMMAND CODE TITLE: PRESENCE SERVICE, SIP CONVERTER, GREETING PROCESS OF SP350 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING The Type of Service SIP Converter PRECEDENCE 0-7 CMBC Y=07 (TOS) field prece- Group ID dence of SIP Con- XX: 01 (Unit No.) verter Control Packet...
Page 697 CMBC COMMAND CODE TITLE: PRESENCE SERVICE, SIP CONVERTER, GREETING PROCESS OF SP350 : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Registration of Stan- Standard SIP sta- XXXX Standard SIP station CM12 Y=97, XXXX number without dard SIP station with- tion ID without out REGISTER...
Page 698: [Cmd7] Oai Control Data
CMD7 COMMAND CODE TITLE: OAI CONTROL DATA FUNCTION: This command is used to assign the data to control the OAI facility. PRECAUTION: When you need to assign the port number of VoIP port of the PBX for OAI, on your computer, assign the number “1024/1025/1039/60030”.
Page 699 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Voice Response System Message number 1XXX Voice Response system No. number for MSF XXX : 000-007 [8300R6 software or before] : 000-015 [8300R7 software or later] Multi-Connection...
Page 700 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Operation code to start up Digit Code (X: 0-9, #) Operation Code for MSF NOTE 4, NOTE 5 NOTE 6 MSF/TMF by dialling a digit code after pressing an OAI function key Operation Code for TMF...
Page 701 CMD7 COMMAND CODE TITLE: OAI CONTROL DATA : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING AP database of FLF Recognition of AP database by To provide RR message Not provided Omission of AP database for Not omitted information added to RR mes- To omit sage...
Page 702: [Cme0] Reset/Instant System Changeover
CME0 COMMAND CODE TITLE: RESET/INSTANT SYSTEM CHANGEOVER FUNCTION: This command allows the maintenance personnel to execute the System Reset, Blade Reset and IPT (P2P CCIS) Reset, Instant System Changeover with the PCPro/CAT. PRECAUTION: If the setting data (Month, Day and Time) is different from the current time of the system clock set by CM02, any request to reset the system is not accepted and “DATA ERROR”...
Page 703 CME0 COMMAND CODE TITLE: RESET/INSTANT SYSTEM CHANGEOVER TYPE OF RESET SETTING DATA RELATED COMMAND MEANING MEANING DATA MEANING Instant System Fixed value Current time dis- CMEC Y=5 Changeover by man- played on Multiline ual operation Terminal/DESKCON [8300R4] NOTE 1 NOTE 9 To request the reset NOTE 10 immediately.
Page 704 CME0 COMMAND CODE TITLE: RESET/INSTANT SYSTEM CHANGEOVER NOTE 8: For the reset (CME0 Y=5>01) while the system is operating, the call connected to a line via IPT (P2P CCIS) is not disconnected NOTE 9: By this command, Active CPU and Stand by CPU are reset, switched and started. NOTE 10: System data copy should be executed by CMEC Y=5 before System Changeover.
Page 705: [Cme1] Cpu Memory Check Sum Display
CME1 COMMAND CODE TITLE: CPU MEMORY CHECK SUM DISPLAY FUNCTION: This command is used to display Check Sum data on CPU memory. This is only for maintenance. PRECAUTION: None ASSIGNMENT PROCEDURE: • To display MEMORY AREA No. ST + + DE (01-11) Check Sum Data: 0000-FFFF is displayed.
Page 706: [Cme4] Station Service Status Display
CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY FUNCTION: This command is used for readout the station service status. PRECAUTION: None ASSIGNMENT PROCEDURE: STATION NUMBER ST + E4YY + DE (1-8 digits) DATA TABLE: READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status abcdefgh a: Terminal connection status...
Page 707 CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status abcdefgh g: Logout/Call Forwarding-PS out of cell (zone) A for each station 0 : Not set 1 : Set h: Do Not Disturb 0 : Not set 1 : Set E: Readout error...
Page 708 CME4 COMMAND CODE TITLE: STATION SERVICE STATUS DISPLAY READOUT DATA RELATED COMMAND MEANING DATA MEANING Readout service status ijklmnop n: ACD/UCD Busy Out CM17 Y=0, 2 B for each station 0 : Not set 1 : Set E: Readout error _ : Not registered ACD/UCD group o: Outgoing Call Restriction 0 : Not set...
Page 709: [Cme5] Station, Trunk Line Make Busy
CME5 COMMAND CODE TITLE: STATION, TRUNK LINE MAKE BUSY FUNCTION: This command is used to make busy any station or trunk in the software. PRECAUTION: None ASSIGNMENT PROCEDURE: STATION/TRUNK DATA + E5Y + NUMBER (1 digit) (1-8 digits) DATA TABLE: : Default STATION/TRUNK NUMBER SETTING DATA...
Page 710 CME5 COMMAND CODE TITLE: STATION, TRUNK LINE MAKE BUSY NOTE 1: For a station that is made busy, call termination to the station is restricted, but call origina- tion is available. For extension lines on a Multiline Terminal, My Line and Multiline make busy can be set in- dividually, with the same condition as mentioned above.
Page 711: [Cme6] Call Forwarding Set/Reset From Pcpro/Cat
CME6 COMMAND CODE TITLE: CALL FORWARDING SET/RESET FROM PCPro/CAT FUNCTION: This command is used to set/reset Call Forwarding service to each station from a PCPro/CAT. PRECAUTION: CME6 can be used for any station irrespective of its state. ASSIGNMENT PROCEDURE: STATION No. DESTINATION No.
Page 712 CME6 COMMAND CODE TITLE: CALL FORWARDING SET/RESET FROM PCPro/CAT : Default MEANING DESTINATION Call Forwarding-PS Out of Cell • Destination=Extension; (Zone) Standard SIP station X-XXXXXXXX: Station No. (1-8 digits) Call Forwarding-Logout (IP Station) • Destination=Outside party; Call Forwarding-Not Available X-XXXX + + YY...YY (Standard SIP station) X-XXXX: Outgoing Trunk Access Code (1-4 digits)
Page 713: [Cme7] Password Level
CME7 COMMAND CODE TITLE: PASSWORD LEVEL FUNCTION: This command is used to specify the accessible commands for each Password Level. PRECAUTION: None ASSIGNMENT PROCEDURE: COMMAND CODE DATA E7YY + DE (2 digits) (1 digit) DATA TABLE: : Default COMMAND CODE SETTING DATA PASSWORD LEVEL Password Level 0-6...
Page 714: [Cme8] Updating Of Access Blade Firmware
CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE FUNCTION: This command is used to update the Access blade (Line/Trunk blades) firmware by PCPro/CAT opera- tion. NOTE: Refer to “PC Programming Manual” for the access blade firmware update. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA...
Page 715 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE DATA TABLE 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Firmware XX ZZ XX: Unit number XX YY ZZ Readout data of firmware CM05 Y=0 download (01-50) when operating ZZ : Slot number XX: Firmware type (Same as (01-18)
Page 716 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING VoIPDB Firmware 10 XX XX: Unit number XX ZZ Readout data of firmware download (01-50) when operating [8300R7] 1101 Stand by CPU XX: Type of VoIPDB 42: PZ-64IPLC-A 44: PZ-128IPLC-A...
Page 717 CME8 COMMAND CODE TITLE: UPDATING OF ACCESS BLADE FIRMWARE 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Read the status of 10 XX XX: Unit number FFFFFF Download is completed VoIPDB firmware (01-50) (normal end) download 1101 Stand by CPU [8300R7] NOTE 1:...
Page 718: [Cme9] Password
CME9 COMMAND CODE TITLE: PASSWORD FUNCTION: This command is used to define the Password of each Password Level and the availability of Password Service. PRECAUTION: When programming a Password, the Password for Password Level 7 must be set. If no Password of Password Level 7 is set, the programming of Password Service provision (CME9>9) is restricted with the message “CODE NOT USED”.
Page 719: [Cmea] Fault Information Store/Display Functions
CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS FUNCTION: This command is used for fault maintenance of the PBX. The functions of this command are outlined below: • Storing fault information into the Fault Store Memory upon occurrence of a fault. •...
Page 720 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Clear External Clear all of MJ/MN /– – alarms MJ alarms OFF/MN Alarm Kind alarms OFF (MJ/MN) (Display only) MJ alarms OFF/MN alarms ON (Display only)
Page 721 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information CS/ZT fault External Alarm Kind CM08>450 and external alarm 0: Fault Memory CM42>01 It is a day for periodic mainte- (Display only) store/No output of nance...
Page 722 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information SIP trunk failure External Alarm Kind CM08>450 and external alarm 0: Fault Memory CM42>01 Remote System Upgrade (Display only) store/No output of Long call duration information...
Page 723 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Power failure External Alarm Kind CM08>450 and external alarm 0: Fault Memory CM42>01 DTI line failure (Display only) store/No output of SV8300 Blade down External Alarm...
Page 724 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Lack of Highway Channel for External Alarm Kind CM08>450 and external alarm data communication 0: Fault Memory CM42>01 [8300R3] (Display only)
Page 725 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Communication error occur- External Alarm Kind CM08>450 and external alarm rence between active CPU and 0: Fault Memory CM42>01 (Display only) stand by CPU...
Page 726 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Communication error occur- External Alarm Kind CM08>450 CM42>01 and external alarm rence between Primary Unit and 0: Fault Memory (Display only) Secondary Unit store/No output of...
Page 727 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Restriction of Remote Mainte- External Alarm Kind CM08>450 CM42>01 and external alarm nance via built-in modem 0: No Fault Memory [8300R7] (Display only) store/No output of...
Page 728 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information SMDR output buffer (SRAM) External Alarm Kind CM08>450 and external alarm return to normal condition from 0: Fault Memory CM42>01 (Display only) overflow...
Page 729 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault information Expansion Chassis (2U) failure External Alarm Kind CM08>450 and external alarm returned to normal condition 0: Fault Memory CM42>01 [8300R3] (Display only)
Page 730 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Fault log/Call log Output destination for the fault RS port of CPU CM40 Y=00 collection on VoIP logs/call logs NOTE 13 Not output call...
Page 731 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS NOTE 1 : Even if the external alarm is set as MN or MJ alarm for system reset (1st data=01), no alarm is output in the case of Power On, Reset key operated, reset from the PCPro/CAT, and reset by CPU SENS switch selection.
Page 732 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS NOTE 6 : About long call duration of trunk call (fault kind: 04A) • When Long call duration failure occurs, “Failure occurred” is displayed on the PCPro. • After a trunk is seized, when the trunk is seized longer time than the monitoring time (1- 60 hours) set by CM42>182, the call is registered as long call duration failure.
Page 733 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS Fault Information Display After the following operation: ST + EA0 + DE 00 + DE The fault information is displayed on PCPro/CAT. An example of fault information display is provid- ed below: CAT mode COMMAND= EA0 +...
Page 734 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS EXPLANATION OF SCREEN INFORMATION 1: Date and Time of Fault Occurrence and Restoration 2: Fault Kind No./Restoration Kind No. FAULT KIND NUMBER FAULT CONTENT System reset CS/ZT fault It is a day for periodic maintenance Activation Code error occurred during the License Activation (Center Activation) ISDN D-channel link connection failure NOTE 2...
Page 735 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS FAULT KIND NUMBER FAULT CONTENT SV8300 Blade reset with CME03 Lack of option value Lack of Highway Channel Auto Blade Reset by TDM-Blade Lockup CPU SRAM failure Restricted blade Firmware version un-matching between CPU blade and Line/Trunk blade Lack of Highway Channel for data communication Illegal use of CPU blade for Remote Unit only Communication error occurrence between active CPU and stand by CPU...
Page 736 CMEA COMMAND CODE TITLE: FAULT INFORMATION STORE/DISPLAY FUNCTIONS RESTORATION RESTORATION CONTENT KIND NUMBER ISDN D-channel link connection returned to normal condition CCIS link connection returned to normal condition NOTE Number of lockout stations restored to less than predetermined number DLC blade returned to normal condition SMDR output buffer (SRAM) return to normal condition from 80 % condition SMDR output buffer (SRAM) return to normal condition from overflow CS/ZT returned to normal condition...
Page 737: [Cmec] Maintenance By Pcpro/Cat
CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT FUNCTION: This command is used for maintenance of the PBX. The functions of this command are outlined below: • Battery release • Line status display for single line telephone or Multiline Terminal • Service Information Display •...
Page 738 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT DATA TABLE: Battery Release/Line Status Display : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Battery release Battery release of Battery released Unit01 + 02 + 03 + Normal operating Unit number Line status Single Line Station...
Page 739 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT (c) Hardware Test STATUS OF STATUS OF INDICATION STATUS OF SINGLE LINE TEL. MULTILINE TERMINAL IP STATION Normal operation of blade NOTE Terminal is not connected or Terminal is not connected Tip wire is grounded Blade is not mounted/initialized Terminal is connected Terminal is connected...
Page 740 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT Service Information Display [8300R5] 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Service Informa- Maximum value of XXXX (Hexadecimal Display) tion Display extension manage- ment number (LEN) NOTE 1 Number of Exten- XXXX (Decimal Display) sion registration...
Page 741 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Service Informa- Number of remain- XXXXX/ XXXXX: tion Display ing number of ZZZZZ Remaining of stored stored call histories call histories (IC) (IC) (System) (System) (Decimal Display)
Page 742 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT System data copy from Active CPU to Stand by CPU by manual operation [8300R4] : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING System data copy Fixed value Start to execute from Active CPU Now executing to Stand by CPU by...
Page 743 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT System Data Backup 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING System data System data backup Start to save CM43 Y=5 backup Now saving Stand by NOTE 6 NOTE 6: You can assign only “0”...
Page 744 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT System Data Copy : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING System data copy All Remote units Start to copy system CM43 Y=7 from the Main unit Remote unit No. 02 data to Remote units Now copying/Sys-...
Page 745 CMEC COMMAND CODE TITLE: MAINTENANCE BY PCPro/CAT Calling party No. for Remote Maintenance [8300R7] : Default 1ST DATA 2ND DATA RELATED COMMAND MEANING DATA MEANING DATA MEANING Calling party No. Calling party No. for XX...XX Calling Party No. CM35 Y=319 for Remote Mainte- Remote Maintenance X: 0-9...
Page 746: [Cmee] Application Blade Data Assignment
CMEE COMMAND CODE TITLE: BLADE RESET APPLICATION BLADE DATA ASSIGNMENT FUNCTION: This command is used to assign the IP address to connect the functions and Web consoles for each In-Skin UMS blade (CD-VM00)/Conference blade (CD-PVAA). PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + EE0 + (4/7 digits)
Page 747 CMEE COMMAND CODE TITLE: BLADE RESET APPLICATION BLADE DATA ASSIGNMENT : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Subnet Mask for XXYY XX: Unit number (01-50) XXX.XX Subnet Mask Conference blade/ YY: Slot number (01-18) ...X (Maximum 15 digits) In-Skin UMS blade XXX.XXX.XXX.XXX= 255.0.0.0-255.255.255.252...
Page 748: [Cmf0] Cpu Memory Dump
COMMAND CODE TITLE: CPU MEMORY DUMP F0, F1 CPU MEMORY READ/WRITE FUNCTION: These commands are used only for maintenance. DO NOT USE these commands without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: CMF0: CPU Memory Dump ZXXXXXXXX ST + + DE...
Page 749: [Cmf5] Line/Trunk Memory/Alarm Memory Read
CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA ST + + DE + DE (1-15 digits)
Page 750 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) Single Line station/Virtual Line LEN switch memory station number (1-8 digits) XXXXXXXX X: 0-9, A (*), B (#) Multiline Terminal number <X-XXXXXXXX> represents My FXXXXXXXX Line number ISDN Line station number ILEN switch memory...
Page 751 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) 0901 Readout the Remote Unit status 00 : Download 01 : Changeover FF: Not used NOTE: This command is avail- able only at Main Unit. 0000 YY + XXXXXXXX +...
Page 752 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) Single Line station/Virtual Line Service memory dump data of station number (1-8 digits) station/trunk XXXXXXXX X: 0-9, A (*), B (#) Multiline Terminal number <X-XXXXXXXX> represent My FXXXXXXXX Line number EFX +...
Page 753 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ READOUT DATA 1ST DATA REMARKS (STATUS INFORMATION) PS Line station number Optional memory dump data <X-XXXXXXXX> of station/trunk EEXXXXXXXX EFX + ISDN Line station number <X-XXXXXXXX> EFXXXXXXXX + B channel number (0/1) D000 Trunk number D511...
Page 754 CMF5 COMMAND CODE TITLE: LINE/TRUNK MEMORY/ALARM MEMORY READ NOTE 2: Status information associated with CMF5 Y=B will be displayed as shown below. Display F5B > X-XXXX : YYYY- /ZZZZ- F52 > FX-FXXXX : YYYY- F52 > D000-D511 : YYYY- YYYYYY: 010101-501832 (Physical Port No.) 3-698 NWA-033623-001 Rev.8.1 91ch3008.fm...
Page 755: [Cmf6] Online Mp-Fp Command Output
CMF6 COMMAND CODE TITLE: ONLINE MP-FP COMMAND OUTPUT FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA 2ND DATA + DE (2 digits) (1-8 digits)
Page 756: [Cmf7] Highway Channel Memory Read/Reassignment
CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 1ST DATA ST + + DE + DE (6 digits)
Page 757 CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT CMF7 Y=9 CMF7 Y=9 is the command which reassigns the high way channel (128ch) allocation to each physical slot (slot1-6/7-12/13-18). For the physical slot, 16 channels are allocated to each slot in reset state (the high way channel allocation is in a state which is not reassigned before).
Page 758 CMF7 COMMAND CODE TITLE: HIGHWAY CHANNEL MEMORY READ/REASSIGNMENT Example: • The setting before mounting the blade Slot 01 16DLC (16) 16DLC (16) Slot 04 Slot 02 16DLC (16) 16DLC (16) Slot 05 Unit01 Slot 03 16DLC (16) 8COT (8) Slot 06 •...
Page 759: [Cmf8] Option Value Read
CMF8 COMMAND CODE TITLE: OPTION VALUE READ FUNCTION: This command is used to read the Option Value. PRECATION: None ASSIGNMENT 1ST DATA ST + + DE + DE (3 digits) DATA TABLE: 1ST DATA READOUT DATA MEANING DATA MEANING DATA MEANING Option Value read PORT Capacity...
Page 760 CMF8 COMMAND CODE TITLE: OPTION VALUE READ 1ST DATA READOUT DATA MEANING DATA MEANING DATA MEANING Option Value read UMS CLIENT XX...XX Option Value NOTE [8300R3] UMS LANGUAGE [8300R2] UMS HOSPI LANG UMS TTS LANG [North America/Australia/ PVA PORT [Australia/North America] [8300R2] NOTE: Example of readout data of the Option Value (CMF8 Y=8>001 [Port Capacity]) on CAT...
Page 761: [Cmfa] Ip Station Apparatus Information
CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION FUNCTION: This command is used to read the apparatus information of IP Station. PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA ST + FAYY/YYYY + DE (1-15 digits) DATA TABLE: 1ST DATA INDICATION MEANING DATA MEANING DATA...
Page 762 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION : Default 1ST DATA INDICATION MEANING DATA MEANING DATA MEANING term term Read the IP Station IP Station No. 75 (D Series E) type/Digital Multiline (IP adapter type) term Terminal Type XXXXXXXX IP INASET term term...
Page 763 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION : Default 1ST DATA INDICATION MEANING DATA MEANING DATA MEANING Read VoIP Encryp- IP Station No. Encryption is effective tion status of DT700 Encryption is ineffective XXXXXXXX series [8300R6] 20XX Execution of ping XXX.XX...X Sending destina- XXX.XX...X: Z XXX.XXX.XXX.XXX= Sending destination IP address...
Page 764 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION NOTE 1: ICMP TYPE used in this feature is as follows. ICMP CLASSI- GENERAL DESCRIPTION MEANING TYPE FICATION Reply Reply to the echo request by executing the • Ping reply (ping OK) ping command (echo reply).
Page 765 CMFA COMMAND CODE TITLE: IP STATION APPARATUS INFORMATION NOTE 2: If ICMP TYPE not listed above is received, “HARDWARE ERROR” is displayed. NOTE 3: TOS (Type of Service) is present in IP header, and represents QoS (Quality of Service). Precedence/delay/throughput/reliability that determine quality are contained within TOS. NOTE 4: This data cannot be set when the first digits of IP address is 0 (ex.
Page 766: [Cmfb] Remote Program Download Information Read, Failover Information Read
COMMAND CODE TITLE: REMOTE PROGRAM DOWNLOAD INFORMATION READ, FAILOVER INFORMATION READ FUNCTION: This command is used only for maintenance. DO NOT USE this command without the assistance of a NEC engineer. ASSIGNMENT PROCEDURE: 2ND DATA 1ST DATA ST + + DE...
Page 767 CMFB COMMAND CODE TITLE: REMOTE PROGRAM DOWNLOAD INFORMATION READ, FAILOVER INFORMATION READ 1ST DATA READOUT DATA MEANING DATA MEANING DATA MEANING Remote Program 01 bb bb : CPU program information Revision Table Information Read 02 : SC No. (For Stand by 03 : Official Version XXXXX XXXXX...
Page 768 CMFB COMMAND CODE TITLE: REMOTE PROGRAM DOWNLOAD INFORMATION READ, FAILOVER INFORMATION READ 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Failover Informa- XX00 Unit operation status Primary Unit: Disconnect tion Read (Display only) Primary Unit: Operating normally [8300R6] XX: Unit No. (01-50) Secondary Unit: Disconnect NOTE1 Secondary Unit: Normal mode...
Page 769: [Cmfc] Voipdb Information Read
CMFC COMMAND CODE TITLE: VoIPDB INFORMATION READ FUNCTION: This command is used to read out the VoIPDB information. [8300R7] PRECAUTION: None ASSIGNMENT PROCEDURE: 1ST DATA ST + FCYY + DE (4 digits) DATA TABLE: : Default 1ST DATA READOUT DATA MEANING DATA MEANING...
Page 770 CMFC COMMAND CODE TITLE: VoIPDB INFORMATION READ : Default 1ST DATA READOUT DATA MEANING DATA MEANING DATA MEANING Unit No. 01 XXX X XXX X VoIPDB informa- *a *b tion Unit No. 50 XXXX NOTE 4 *a: Type of VoIPDB firmware revision NOTE 1 XXXX 100: Firmware version on the VoIPDB...
Page 771 CMFC COMMAND CODE TITLE: VoIPDB INFORMATION READ : Default 1ST DATA 2ND DATA MEANING DATA MEANING DATA MEANING Unit No. 01 Latest Previous time of aaaabb aaaa: Year SNTP execution ccddee bb : Month Unit No. 50 NOTE 3 cc : Day NOTE 1 dd : Hour NOTE 2...
Page 772 THIS PAGE LEFT BLANK INTENTIONALLY. 3-716 NWA-033623-001 Rev.8.1 91ch3008.fm JUNE/15/2011...
Page 773 UNIVERGE SV8300 Command Manual TERMINAL KEY ASSIGNMENT Appendix This appendix contains the key number layout of each DT300 term term Series, DT700 Series, D IP, DESKCON, DSS Console, and Add-On Module. Refer to this appendix when you assign a key function by CM90 or CM97.
Page 774 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Recall Feature (95) Answer Menu DTL-12D-1D Redial Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 775 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Recall Feature (95) Answer Menu DTL-12D-1D+8LK Redial Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 776 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Recall Feature (95) Answer Menu DTL-12D-1D+16LK Redial Hold Transfer Speaker (97) (96) (94) 16LK NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the...
Page 777 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) 12LK (91) (90) Recall Feature (95) Answer Menu Redial Hold Transfer Speaker (97) (96) (94) DTL-12D-1D+12LK NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the...
Page 778 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Example: 24 Line/Trunk/Feature Keys Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (17) (18) (91) (90) Recall Feature (95) Answer Menu Redial Hold Transfer Speaker...
Page 779 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Example: 24 Line/Trunk/Feature Keys Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (17) (18) (91) (90) Recall Feature (95) Answer Menu Redial DTL-24D-1D+8LK Hold...
Page 780 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Example: 24 Line/Trunk/Feature Keys Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (17) (18) (91) (90) Feature Recall (95) Answer Menu DTL-24D-1D+16LK Redial Hold...
Page 781 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Exit Help (01) (05) (06) (02) (07) (03) (04) (08) Scroll (91) (90) Recall Feature (95) Answer Menu Redial DTL-8LD-1D Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 782 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (05) (01) (02) (06) (07) (03) (04) (08) Scroll (91) (90) Feature Recall (95) Answer Menu Redial DTL-24D-1D+8LK Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 783 Appendix A TERMINAL KEY ASSIGNMENT DT300/DT700 Series Key Numbers Key Numbers Help Exit (05) (01) (02) (06) (07) (03) (08) (04) Scroll (91) (90) Recall Feature (95) Answer Menu Redial DTL-8LD-1D+16LK Hold Transfer Speaker (97) (96) (94) 16LK NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 784 Appendix A TERMINAL KEY ASSIGNMENT DT700 Series Key Numbers Key Numbers (01) (05) (02) (06) (03) (07) (04) (08) Exit Help Scroll (90) (91) Feature Recall (95) Answer ITL-8LDE-1 Menu Redial Speaker Hold Transfer (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 785 Appendix A TERMINAL KEY ASSIGNMENT DT300 Series Key Numbers [8300R2] Key Numbers Help Exit (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (91) (90) Recall Feature (95) DTL-12BT-1 Answer Menu Redial Hold Transfer Speaker (97) (96) (94) NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the...
Page 786 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term term Series i Series i (01) (02) (03) (04) (05) (06) (07) (08) Recall Feature (98) (90) (91) Directory Conf (99) Message (92) Redial PQRS WXYZ (93) Answer (95) Transfer...
Page 787 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term term Series i Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) Recall Feature (98) Directory (90) (91) NOTE 1 Conf (99) Message (92) Redial PQRS WXYZ...
Page 788 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term term Series i Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) Recall Feature (98) (90) (91) Directory NOTE 1...
Page 789 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One-Touch Keys term term Series i Series i Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15)
Page 790 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term term Series i Series i Exit Help ( 0 1 ) ( 0 9 ) ( 0 2 ) ( 1 0 ) ( 0 3 ) ( 11 ) ( 0 4 ) ( 1 2 )
Page 791 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Key Numbers Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (91) PQRS WXYZ Feature (90) Recall (92) DTR-8D-1R Conf (93) Redial (94) Speaker (97) (96) (95) (98) Hold...
Page 792 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers term Key Numbers Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) PQRS WXYZ Feature (90) Recall (92) DTR-16D-1R Conf (93)
Page 793 Appendix A TERMINAL KEY ASSIGNMENT term term Series i/D IP Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One-Touch Keys Exit Help (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) Feature (90) Recall (92)
Page 794 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (03) (02) (04) (06) (07) (08) (05) (91) Feature (90) Recall (92) Conf (93) Redial (97) (96) (95) (94) DTP-8-1 Answer Transfer Speaker Hold NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 795 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (02) (03) (04) (05) (06) (07) (08) (91) Feature (90) Recall (92) Conf DTP-8D-1 (93) Redial (97) (96) (95) (94) Answer Speaker Hold Transfer NOTE: The table below shows the key layout for Line/Trunk/Feature Keys and One Touch Keys of the Multiline Terminals.
Page 796 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers term Key Numbers (01) (02) (03) (04) (05) (06) (07) (08) (09) (10) (11) (12) (13) (14) (15) (16) (91) Feature (90) Recall (92) Conf DTP-16D-1 (93) Redial (97) (96) (95) (94) Answer Speaker...
Page 797 Appendix A TERMINAL KEY ASSIGNMENT term 75 Key Numbers Example: 16 Line/Trunk/Feature Keys + 16 One Touch Keys (01) (02) (03) (04) (06) (07) (05) (08) (09) (12) (10) (11) (13) (16) (14) (15) (91) Feature (90) Recall (92) Conf DTP-32D-1 (93) Redial...
Page 798 Appendix A TERMINAL KEY ASSIGNMENT DESKCON Key Numbers (01) (02) (03) (04) Night Busy ATND NANS Recall PAGE (13) (14) (15) (16) (17) (18) (19) (20) (21) (22) Start Mute Call Park Position Busy (23) (24) (26) (27) (31) (32) Cancel Volume L6 (12)
Page 799 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers DCR-60-1R Continued on next page A-27 NWA-033623-001 Rev.8.1 91apa001.fm...
Page 800 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers DCU-60-1 Continued on next page A-28 NWA-033623-001 Rev.8.1 91apa001.fm...
Page 801 Appendix A TERMINAL KEY ASSIGNMENT DSS Console Key Numbers EDW-48-2 A-29 NWA-033623-001 Rev.8.1 91apa001.fm...
Page 802 Appendix A TERMINAL KEY ASSIGNMENT Add-On Module Key Numbers DCU-60-1 Continued on next page A-30 NWA-033623-001 Rev.8.1 91apa001.fm...
Page 803 Appendix A TERMINAL KEY ASSIGNMENT Add-On Module Key Numbers EDW-48-2 A-31 NWA-033623-001 Rev.8.1 91apa001.fm...
Page 804 THIS PAGE LEFT BLANK INTENTIONALLY. A-32 NWA-033623-001 Rev.8.1 91apa001.fm JUNE/15/2011...

NEC UNIVERGE SV8300 Command Manual

Introduction

Chapter 1 HOW to USE CAT

Chapter 2 PRECAUTION

Chapter 3 COMMAND DESCRIPTION

Quick Links

Related Manuals for NEC UNIVERGE SV8300

Summary of Contents for NEC UNIVERGE SV8300