Honeywell SiX series Quick Installation Manual
Wireless occupancy sensor
Hide thumbs
Also See for SiX series:
- Installation instructions manual (12 pages) ,
- Manual (8 pages) ,
- Installation instructions (4 pages)
Advertisement
Quick Links
SiXOCC
Wireless Occupancy Sensor /
QUICK INSTALLATION GUIDE
The Honeywell SiXOCC Occupancy Sensor is a wireless device
used with controllers that support Honeywell's SiX™ series devices.
The SiXOCC combines security motion detection and automation
in one unit. Using automation mode allows the device to signal the
control to turn a light on or off and/or a thermostat to a
pre-programmed temperature.
NOTES: Lights controlled via Z-Wave devices have not been
evaluated by ETL.
MOUNTING LOCATIONS / EMPLACEMENTS DE MONTAGE
MOUNTING OPTIONS / OPTIONS DE MONTAGE
ENROLL THE SIXOCC/ ENRÔLEMENT DU DÉTECTEUR
After enrolling, update the SiXOCC firmware (via the Controller)
to ensure the latest version is used. See the Controller's
instructions.
NOTE: Once enrolled, the device cannot be used with another
system until it is removed from the current controller.
See the controller's instructions.
To enroll in Honywell's Lyric control panel follow the steps below:
WALK TEST / TEST PAR DÉPLACEMENT
NOTE: Before using Test Mode, the device must first be enrolled in
the Controller.
When in walk test the LED shows red for intrusion and green for
occupancy.
Wireless Occupancy Sensor
Après l'enrôlement, faites la mise à jour du microprogramme du SiXOCC (via le
panneau de commande) afin de vous assure qu'il utilise la plus récente version.
Reportez-vous aux instructions du panneau.
NOTE : Une fois enrôlé, le dispositif ne peut pas être utilisé avec un autre
NOTE: Avant d'utiliser le mode de test, le dispositif doit d'abord être
When in walk test the LED shows red for intrusion and green for occupancy.
GUIDE D'INSTALLATION RAPIDE
The Honeywell SiXOCC Occupancy Sensor is a wireless device used with
controllers that support Honeywell's SiX™ series devices.
The SiXOCC combines security motion detection and automation in one
unit. Using automation mode allows the device to signal the control to
turn a light on or off and/or a thermostat to a pre-programmed
temperature.
NOTES: Lights controlled via Z-Wave devices have not been
evaluated by ETL.
OPEN / OUVERT
NOTE: After enrolling and before mounting
NOTE: Après avoir enrôlé l'unité et avant de
système avant d'avoir été supprimé du panneau actuel. Reportez-vous
aux instructions du panneau.
dans le panneau.
permanently, conduct go/no go tests
(see controller's instructions) to verify
adequate signal strength.
la mettre en place de façon
permanente, effectuez des tests tout
ou rien (voir les instructions du
panneau de commande) pour vérifier
que la puissance du signal est
adéquate. Au besoin, modifiez
l'emplacement ou l'orientation du
dispositif.
enrôlé
Advertisement
Related Manuals for Honeywell SiX series
Summary of Contents for Honeywell SiX series
- Page 1 QUICK INSTALLATION GUIDE GUIDE D'INSTALLATION RAPIDE The Honeywell SiXOCC Occupancy Sensor is a wireless device The Honeywell SiXOCC Occupancy Sensor is a wireless device used with used with controllers that support Honeywell’s SiX™ series devices. controllers that support Honeywell’s SiX™ series devices.
-
Page 2: Led Indicators
For full details, refer to the installation instructions (document # 800-23973) at https://mywebtech.honeywell.com. Ê800-23891ZŠ Honeywell is a registered trademark of Honeywell International Inc. All other trademarks are the properties of their respective owners. All rights reserved. Honeywell est une marque déposée de Honeywell International Inc. Toutes les autres marques de 800-23891 2/18 Rev A commerce appartiennent à...