hit counter script

Cisco TelePresence ISDN Link Reference Manual page 24

Hide thumbs Also See for TelePresence ISDN Link:
Table of Contents

Advertisement

Cisco TelePresence ISDN Link
Contents
Introduction
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1472 Prefix
Defines the prefix to be used with the RS366 Custom IMUX at this bandwidth..
Value space:
<S: 0, 12>
Format: String with a maximum of 12 characters.
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1472 Prefix: ""
Example:
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1472 Suffix
Defines the suffix to be used with the RS366 Custom IMUX at this bandwidth.
Value space:
<S: 0, 12>
Format: String with a maximum of 12 characters.
Example:
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1472 Suffix: ""
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1472R Prefix
Defines the prefix to be used with the RS366 Custom IMUX at this restricted bandwidth.
<S: 0, 12>
Value space:
Format: String with a maximum of 12 characters.
Example:
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1472R Prefix: ""
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1472R Suffix
Defines the suffix to be used with the RS366 Custom IMUX at this restricted bandwidth.
Value space:
<S: 0, 12>
Format: String with a maximum of 12 characters.
Example:
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1472R Suffix: ""
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1920 Prefix
Defines the prefix to be used with the RS366 Custom IMUX at this bandwidth.
Value space:
<S: 0, 12>
Format: String with a maximum of 12 characters.
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1920 Prefix: ""
Example:
xConfiguration ExternalNetwork Interface [1..1] CustomIMUX bw1920 Suffix
Defines the suffix to be used with the RS366 Custom IMUX at this bandwidth.
Value space:
<S: 0, 12>
Format: String with a maximum of 12 characters.
Example:
xConfiguration ExternalNetwork Interface 1 CustomIMUX bw1920 Suffix: ""
D14953.01
ISDN Link API Reference Guide IL1.0 June 2012.
© 2012 Cisco Systems, Inc. All rights reserved.
About the API
xConfiguration
xConfiguration
The Gateway configuration
xConfiguration Gateway SIP PeerUri
xConfiguration Gateway SIP PeerHost
24
xCommand
Set the address be used to reach the peer codec for incoming H.320 side calls when SIP (VCS)
registered mode is used. It should hold the same setting as the peer codec uses to register itself
on the VCS server. If SIP registered mode is not used, this setting is not used. (VCS = Video
Communication Server)
Value space:
<S: 0, 256>
Format: Compact string with a maximum of 256 characters.
Example:
xConfiguration Gateway SIP PeerUri: "sip-codec@domain.com"
Set the IP address of the peer SIP codec using the ISDN link. Only one SIP codec can use the ISDN
link, and it must be on the same subnet as the ISDN link. This IP address must correspond to the IP
address type (IPv4 or IPv6) that the codec is configured to use for SIP calls.
The address is used for:
1) Verification of the SIP remote media transport addresses (if there is a mismatch, the call will be
rejected/disconnected).
2) System status monitoring, indicating alarm etc if specified codec is not reachable.
3) If not SIP (VCS) registered, this address is used to call the SIP codec for incoming H.320 side calls.
(VCS = Video Communication Server)
Value space:
<S: 0, 64>
Format: Compact string with a maximum of 64 characters.
xConfiguration Gateway SIP PeerHost: "10.0.0.100"
Example:
API Reference Guide
xStatus
Contact us
www.cisco.com

Advertisement

Table of Contents
loading

Table of Contents