Cisco TelePresence System Codec C40 Administrator's Manual page 79
Hide thumbs
Also See for TelePresence System Codec C40:
- Reference manual (224 pages) ,
- Administrator's manual (151 pages) ,
- User manual (51 pages)
Table of Contents
Advertisement
Cisco TelePresence System Codec C40/C60 and Profiles using C40/60
Contents
Network [1..1] IEEE8021X Eap Ttls
Set the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the
need for client certificates. Developed by Funk Software and Certicom. Usually supported by
Agere Systems, Proxim and Avaya.
Requires user role: ADMIN
Value space: <Off/On>
Off: The EAP-TTLS protocol is disabled.
On: The EAP-TTLS protocol is enabled (default).
Network 1 IEEE8021X Eap Ttls: On
Example:
Network [1..1] IEEE8021X Eap Tls
Enable or disable the use of EAP-TLS (Transport Layer Security) for IEEE802.1x connections.
The EAP-TLS protocol, defined in RFC 5216, is considered one of the most secure EAP
standards. LAN clients are authenticated using client certificates.
Requires user role: ADMIN
Value space: <Off/On>
Off: The EAP-TLS protocol is disabled.
On: The EAP-TLS protocol is enabled (default).
Network 1 IEEE8021X Eap Tls: On
Example:
Network [1..1] IEEE8021X Eap Peap
Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients
without the need for client certificates. Developed by Microsoft, Cisco and RSA Security.
Requires user role: ADMIN
Value space: <Off/On>
Off: The EAP-PEAP protocol is disabled.
On: The EAP-PEAP protocol is enabled (default).
Network 1 IEEE8021X Eap Peap: On
Example:
D14636.10
Profile C60-C40 and Codec C60-C40
Introduction
Web interface
Administrator Guide TC6.1, APRIL 2013.
System settings
System settings
Network [1..1] MTU
Set the Ethernet MTU (Maximum Transmission Unit).
Requires user role: ADMIN
Value space: <576..1500>
Range: Select a value from 576 to 1500 bytes.
Network 1 MTU: 1500
Example:
Network [1..1] Speed
Set the Ethernet link speed.
NOTE: If running older software versions than TC6.0, restart the system for any change to this
setting to take effect.
Requires user role: ADMIN
Value space: <Auto/10half/10full/100half/100full/1000full>
Auto: Autonegotiate link speed.
10half: Force link to 10 Mbps half-duplex.
10full: Force link to 10 Mbps full-duplex.
100half: Force link to 100 Mbps half-duplex.
100full: Force link to 100 Mbps full-duplex.
1000full: Force link to 1 Gbps full-duplex.
Network 1 Speed: Auto
Example:
Network [1..1] TrafficControl Mode
Set the network traffic control mode to decide how to control the video packets transmission
speed.
Requires user role: ADMIN
Value space: <Off/On>
Off: Transmit video packets at link speed.
On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the
outgoing network traffic.
Network 1 TrafficControl: On
Example:
www.cisco.com — Copyright © 2010-2013 Cisco Systems, Inc. All rights reserved.
79
Administrator Guide
Setting passwords
Appendices
- Quick Links:
- Codec C40 at a Glance
- Factory Reset
Hide quick links:
Advertisement
Chapters
Table of Contents
