ALIGNMENT PROCEDURE Base Unit Transmitter Section BASE Unit AF GEN. Test Point Connections Power Meter DC IN TEL Line 1kHz -15dBm 9V Jack Jack Test Point Frequency Counter AC 120V Adapter 60Hz Deviation Mater Preset Press the “PAGE” key about 3.0 seconds while truning the power on. Alignment Procedure step Adjustment...
Page 5
Receiver Section Connections BASE Unit AC Voltmeter RF SG Dummy Load (600-ohm) TEL Line Test Point Jack DC Voltmeter DC IN 9V Jack Test Point AC 120V 60Hz Adapter Preset Place the Base Unit in RX SENS mode (step 4) in accordance with the precedure on page 3. Alignment Procedure step Preset to...
Page 6
Handset Unit Transmitter Section Connection HANDSET Unit AF GEN. Test Point Power Meter J601 Battery 1kHz 9mV MIC+Pin Connector Test Point Frequency Counter DC Power Supply Deviation Mater DC 3.8V Preset a) Connect the handseet RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit.
Page 7
Receiver Section Connections HANDSET Unit AC Voltmeter RF SG Dummy Load (150-ohm) Test Point Terminal DC Power Supply J601 DC Voltmeter Battery Test Point Connector DC 3.8V Preset a) Connect the handset RF unit to the handset main unit. b) Connect DC power supply to battery connector on the handset unit. c) Turn the DC power supply ON while pressing “...
TROUBLESHOOTING HINTS 1. The bell does not ring. Set RINGER ON/OFF SW on Check RINGER ON/OFF SW on Base to ON position. Base ON Position. See 2. The bell does not ring When the PAGE SW of the & page does not ring. base is pressed, does the ringer on the handset ring? When the TEL SG is joined...
Page 15
2. The bell does not ring & page does not ring. Can the base and handset be See 3. The base and handset connected? cannot be connected. Press handset DIAL key When the key of the handset is Check IC604. while in TALK MODE.
Page 16
3. The base and handset cannot be connected. Check whether the base Check IC11 and its is able to set in the test peripheral circuit. mode 1. Check the TX POWER Check base RF unit. and the TX FREQUENCY on the base unit. Set the base in the test Check whether there is a Check RT3, R30, R76,...
Page 17
Set the handset in the Check whether there is a Check RT603, R641, test mode 3, check 250 Hz data waveform at R642, R643, R644, whether deviation of the “MOD” of RF unit. R645 and C653. TX data is app. 9.0 kHz Dev.
Page 18
4. Cannot make a phone call (pulse). Can the base and handset See 3. The base and handset be connected? cannot be connected. While in TALK MODE, press Check IC11. dial key of the handset. Check whether square waveform from pin 13 of IC11 is fed.
6. Voice cannot be transmitted to other party (outgoing call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, 9.0mV sine Check Q604 and its wavefor m i s a p p l i e d t o peripheral circuit.
Page 20
7. The voice of the caller cannot be heard (incoming call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, -15dBm sine Check the base TEL-line waveform is applied to TEL- circuit and REPLAY control line of the base, can the 1 kHz circuit.
IC AND TRANSISTOR VOLTAGE CHART Base Unit, Main Unit[V] Unit[V] Ref. No. PIN STBY TALK NOTE Ref. No. PIN STBY TALK NOTE DATA(PULSE) X'TAL X'TAL X'TAL X'TAL IC11...
PARTS LIST PRODUCT SAFETY NOTE : Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don’t degrade the safety of the product through important servicing. Symbol Symbol ±...
Page 41
LOC. REF. PART NO. DESCRIPTION RC008843 BCML313335Z CERAMIC M/L (1608) 0.033UF 16V K B RC008270 BCML811235Z CERAMIC M/L (1608) 0.012UF 50V K B RC008318 BCML815625Z CERAMIC M/L (1608) 0.0056UF 50V K B RC001809 BCAZ814786Z ELECTROLYTIC 0.47UF 50V M C-156 RC008318 BCML815625Z CERAMIC M/L (1608) 0.0056UF 50V K B...
Page 42
LOC. REF. PART NO. DESCRIPTION RC008106 BCAZ313316Z ELECTROLYTIC 330UF 16V M C-156 RC005205 BCML811035Z CERAMIC M/L (1608) 0.01UF 50V K B RC001795 BCAZ112216Z ELECTROLYTIC 220UF 10V M C-156 RC001794 BCAZ111016Z ELECTROLYTIC 100UF 10V M C-156 RC005468 BCEQ904706Z ELECTROLYTIC 47UF 6.3V M C-125 RC005205 BCML811035Z CERAMIC M/L (1608)
Page 43
LOC. REF. PART NO. DESCRIPTION C231 RC008731 BCXK311050Z CERAMIC M/L (2125) 1UF 16V Z F C232 RC001794 BCAZ111016Z ELECTROLYTIC 100UF 10V M C-156 C453 RC009271 BCDB901016Z ELECTROLYTIC 100UF 6.3V M C-326 C455 RC009372 BCML511835Z CERAMIC M/L (1608) 0.018UF 25V K B C456 RC008296 BCSH901006Z TANTALUM CHIP...
Page 44
LOC. REF. PART NO. DESCRIPTION C614 RC005202 BCML311045Z CERAMIC M/L (1608) 0.1UF 16V K B C616 RC008731 BCXK311050Z CERAMIC M/L (2125) 1UF 16V Z F C617 RC004347 BCXK514740Z CERAMIC M/L (2125) 0.47UF 25V Z F C618 RC002229 BCXT511045Z CERAMIC M/L (2125) 0.1UF 25V K B C619 RC008270 BCML811235Z...
Page 45
LOC. REF. PART NO. DESCRIPTION C665 RC005207 BCML813325Z CERAMIC M/L (1608) 0.0033UF 50V K B C666 RC005207 BCML813325Z CERAMIC M/L (1608) 0.0033UF 50V K B C667 RC009271 BCDB901016Z ELECTROLYTIC 100UF 6.3V M C-326 C668 RC005205 BCML811035Z CERAMIC M/L (1608) 0.01UF 50V K B C669 RC008296 BCSH901006Z TANTALUM CHIP...
WSLV435626Z MIRROR MAT RC009416 WSLV447515Z SLEEVE ASSEMBLY PARTS LIST NOTE: Following part numbers are not available as replacement parts. Order parts necessary for repair or contact the Toshiba Factory Service Center. LOC. REF. PART NO. DESCRIPTION RC009537 AC269BHBA BASE MAIN PCB ASSEMBLY...