OPERATING CONTROLS HANDSET CONTROLS AND FUNCTIONS SETTING THE DIAL MODE 1 Press and hold until you hear FLASH Antenna a confirmation tone. 2 To set the dial mode for pulse dialing, press . Or to set the dial mode for tone dialing press .
ANSWERING MACHINE SETTING THE CLOCK 1. Press twice, then press MENU 2. Select the day of the week by pressing . When the correct day is announced, SELECT SELECT press 3. Select the hour by pressing . When the correct hour is announced, press SELECT SELECT 4.
ALIGNMENT PROCEDURE Base Unit Transmitter Section Connections BASE Unit AF GEN. Test Point Power Meter DC IN TEL Line 1kHz -10.5dBm 9V Jack Jack Test Point Frequency Counter AC 120V Adapter 60Hz Deviation Meter Preset Press and hold the “ANSWER” key about 5.0 seconds while turning the 7 SEG LED shows “8” . Alignment Procedure step Adjustment...
Page 6
Receiver Section Connections BASE Unit AC Voltmeter RF SG Dummy Load (600-ohm) TEL Line Test Point Jack DC Voltmeter DC IN 9V Jack Test Point AC 120V 60Hz Adapter Preset Place the Base Unit in RX SENS mode (step 11) in accordance with the precedure on page 4. Alignment Procedure step Preset to...
Page 7
Handset Unit Transmitter Section Connections HANDSET Unit AF GEN. Test Point Power Meter J601 Battery 1kHz 9mV MIC+Pin Connector Test Point Frequency Counter DC Power Supply Deviation Meter DC 3.8V Preset a) Connect DC power supply to battery connector on the handset unit. b) Turn the DC power supply ON while pressing “...
Page 8
Receiver Section Connections HANDSET Unit AC Voltmeter RF SG Dummy Load (150-ohm) Test Point Terminal DC Power Supply J601 DC Voltmeter Battery Test Point Connector DC 3.8V Preset a) Connect DC power supply to battery connector on the handset unit. b) Turn the DC power supply ON while pressing “...
TROUBLESHOOTING HINTS 1. The bell of base unit does not ring. Set RINGER volume setting Check RINGER mode setting is Hi or Low. to Hi or Low. See 2. The bell does not ring When the PAGE SW of the &...
Page 15
2. The bell of handset does not ring & page does not ring. Can the base and handset be See 3. The base and handset connected? cannot be connected. Press handset DIAL key When the key of the handset is Check IC608.
Page 16
3. The base and handset cannot be connected. Check whether the base Check IC6 and its is able to set in the test peripheral circuit. mode 8. Check the TX POWER Check base RF section. and the TX FREQUENCY on the base unit. Set the base in the test Check whether there is a Check RT2, R91, R98,...
Page 17
Set the handset in the Check whether there is a Check R668, R712, test mode 3, check 250 Hz data waveform at R713, R716, R717, whether deviation of the RT602. C719, C748 and RT602. TX data is app. 9.0 kHz Dev.
Page 18
4. Cannot make a phone call (pulse). Can the base and handset See 3. The base and handset be connected? cannot be connected. While in TALK MODE, press Check IC6. dial key of the handset. Check whether square waveform from Pin 80 of IC6 is fed.
6. Voice cannot be transmitted to other party (outgoing call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, 9.0mV sine waveform is applied to MC601 + side. Check Check IC602 and its peripheral circuit.
Page 20
7. The voice of the caller cannot be heard (incoming call). Can the base and handset be See 3. The base and handset connected? cannot be connected. The 1 kHz, -10.5dBm sine Check the base TEL-line waveform is applied to TEL- circuit and RELAY control line of the base, can the 1 kHz circuit.
PARTS LIST PRODUCT SAFETY NOTE: Products marked with a have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice of this service manual. Don’ t degrade the safety of the product through important servicing. Symbol Symbol ±1...
Page 37
LOC. PART NO. REF NO. DESCRIPTION RC008062 BCMM817092Z CERAMIC M/L 7PF 50V D CH RC005205 BCML811035Z CERAMIC M/L 0.01UF 50V K B RC005360 BCMM816092Z CERAMIC M/L 6PF 50V D CH RC005222 BCMS811091Z CERAMIC M/L 1PF 50V C CK RC005223 BCMS812091Z CERAMIC M/L 2PF 50V C CK RC005202...
Page 38
LOC. PART NO. REF NO. DESCRIPTION RC001806 BCAZ812286Z ELECTROLYTIC 0.22UF 50V M C-156 C098 RC005202 BCML311045Z CERAMIC M/L 0.1UF 16V K B RC005202 BCML311045Z CERAMIC M/L 0.1UF 16V K B C100 RC005420 BCMM811514Z CERAMIC M/L 150PF 50V J CH C101 RC005202 BCML311045Z CERAMIC M/L...
Page 39
LOC. PART NO. REF NO. DESCRIPTION C159 RC005205 BCML811035Z CERAMIC M/L 0.01UF 50V K B C160 RC005205 BCML811035Z CERAMIC M/L 0.01UF 50V K B C161 RC005209 BCMM811002Z CERAMIC M/L 10PF 50V D CH C162 RC005216 BCMM813304Z CERAMIC M/L 33PF 50V J CH C163 RC005216 BCMM813304Z...
ASSEMBLY PARTS LIST NOTE: Following part numbers are not available as replacement parts. Order parts necessary for repair or contact the Toshiba Factory Service Center. LOC. PART NO. REF NO. DESCRIPTION RC012309 AC339BHBA MAIN PCB ASSY, BASE RC012310 AC339BHBB KEY PCB ASSY, BASE...
SPECIFICATIONS MEASUREMENT CONDITIONS 1. Standard Voltage: DC 3.8 V ±0.025 V Portable Unit AC 120 V ±3 V 60 Hz Base Unit 25 °C ±5 °C 2. Temperature: 3. Channel: Portable (TX Frequency) Base (TX Frequency) 904.052470 MHz 925.997470 MHz 902.102465 MHz 926.047470 MHz 902.152465 MHz...
Page 55
BASE UNIT RECEIVER Unit Nominal Limit −115 < −107 1. Sensitivity 12 dB SINAD (with CCITT Filter) 2. Frequency Response (Ref: 1 kHz) −4.0 ~ +4.0 0.3 kHz −2.0 −6.0 ~ +2.0 3.0 kHz 3. Distortion at 1 mV RF Input <...
Page 56
HANDSET UNIT RECEIVER Unit Nominal Limit −115 1. Sensitivity 12 dB SINAD (with CCITT Filter) <−107 2. AF Frequency Response (Ref: 1 kHz at 5 kHz Dev) 0.3 kHz +7.0 +3.0 ~ +11.0 −10.0 −14.0 ~ −6.0 3.0 kHz LOW +15 ±3 3.
Page 57
REFERENCE DIGITAL ANSWERING SYSTEM Setting The Dial Mode Recording and Setting the Greeting Message GUIDE FT-8901A Depending on your dialing system, set the mode as follows: To record the greeting message: REC MEMO/2WAY Read the Owner’s Manual for details. MENU...
Page 58
CORDLESS TELEPHONE DIGITAL ANSWERING SYSTEM Ajuste del modo de marcación Grabación y ajuste de un mensaje de contestación FT-8901A Para grabar un mensaje de contestación: Según su sistema de marcación, ajuste el modo de la manera siguiente: REC MEMO/2WAY Para los detalles, lea el manual de instrucciones (en inglés).
Page 59
TOSHIBA AMERICA CONSUMER PRODUCTS, INC. 82 TOTOWA ROAD, WAYNE, N.J. 07470 TOSHIBA HAWAII, INC. 327 KAMAKEE ST., HONOLULU, H.I. 96814...