Cisco TelePresence Codec C90 Administrator's Manual page 48
Telepresence system
Hide thumbs
Also See for TelePresence Codec C90:
- Reference manual (225 pages) ,
- Manual (25 pages) ,
- Installing manual (2 pages)
Table of Contents
Advertisement
Cisco TelePresence System Codec C90 and Profile 65" Dual using C90
Contents
Introduction
Network [1..1] IEEE8021X Eap Peap
Set the Peap (Protected Extensible Authentication Protocol) mode. Authenticates LAN clients
without the need for client certificates. Developed by Microsoft, Cisco and RSA Security.
Requires user role: ADMIN
Value space: <On/Off>
On: The EAP-PEAP protocol is enabled (default).
Off: The EAP-PEAP protocol is disabled.
Example: Network 1 IEEE8021X Eap Peap: On
Network [1..1] IEEE8021X Eap Ttls
Set the TTLS (Tunneled Transport Layer Security) mode. Authenticates LAN clients without the
need for client certificates. Developed by Funk Software and Certicom. Usually supported by
Agere Systems, Proxim and Avaya.
Requires user role: ADMIN
Value space: <On/Off>
On: The EAP-TTLS protocol is enabled (default).
Off: The EAP-TTLS protocol is disabled.
Example: Network 1 IEEE8021X Eap Ttls: On
Network [1..1] MTU
Set the Ethernet MTU (Maximum Transmission Unit).
Requires user role: ADMIN
Value space: <576..1500>
Range: Select a value from 576 to 1500 bytes.
Example: Network 1 MTU: 1500
Network [1..1] Speed
Set the Ethernet link speed.
Requires user role: ADMIN
Value space: <Auto/10half/10full/100half/100full/1000full>
Auto: Autonegotiate link speed.
10half: Force link to 10 Mbps half-duplex.
10full: Force link to 10 Mbps full-duplex.
100half: Force link to 100 Mbps half-duplex.
100full: Force link to 100 Mbps full-duplex.
1000full: Force link to 1 Gbps full-duplex.
Example: Network 1 Speed: Auto
D14635.0
6 Profile C90 and Codec C90 Administrator Guide TC4.2, July 2011.
Copyright © 2010-2011 Cisco Systems, Inc. All rights reserved.
Web interface
Advanced settings
Advanced settings
Network [1..1] TrafficControl Mode
Set the network traffic control mode to decide how to control the video packets transmission
speed.
Requires user role: ADMIN
Value space: <On/Off>
Example: Network 1 TrafficControl: On
Network [1..1] RemoteAccess Allow
Filter IP addresses for access to ssh/telnet/HTTP/HTTPS.
Requires user role: ADMIN
Value space: <S: 0, 255>
Example: Network 1 RemoteAccess Allow: "192.168.1.231, 192.168.1.182"
Network [1..1] VLAN Voice Mode
Set the VLAN voice mode.
Requires user role: ADMIN
Value space: <Manual/Off>
Example: Network 1 VLAN Voice Mode: Off
Network [1..1] VLAN Voice VlanId
Set the VLAN voice ID.
Requires user role: ADMIN
Value space: <1..4094>
Example: Network 1 VLAN Voice VlanId: 1
Network [1..1] VLAN Voice Priority
Set the VLAN voice priority.
Requires user role: ADMIN
Value space: <0..7>
Example: Network 1 VLAN Voice Priority: 0
48
Password protection
On: Transmit video packets at maximum 20 Mbps. Can be used to smooth out bursts in the
outgoing network traffic.
Off: Transmit video packets at link speed.
Format: String with a maximum of 255 characters, comma separated IP adresses or IP range.
Manual: The voice packets in the VLAN network are manually tagged with VlanId and Priority.
Off: The voice packets in the VLAN network are untagged.
Range: Select a value from 1 to 4094.
Range: Select a value from 0 to 7.
Administrator guide
Appendices
Contact us
www.cisco.com
Advertisement
Table of Contents
