Advertisement
Quick Links
equIP® Series 720p/1080p Indoor IP
Micro Dome Camera
Document 800-15436V3 — Rev B — 06/2014
Introduction
Thank you for purchasing a Honeywell equIP Series 720p/1080p Indoor IP Micro Dome
Camera. Before installing this camera, please carefully read this guide and verify your
model:
H2S1P6(X): 720p
resolution, 4.0 mm
lens micro dome IP
2.0"
camera
(49.75 mm)
1.8"
(45.88 mm)
4.4"
H2S2P6(X): 1080p
(110.89 mm)
resolution, 4.0 mm
lens micro dome IP
ø4.3"
(110.2 mm)
camera
For detailed information about your specific camera, please refer to the appropriate user
guide located on the software and documentation CD.
Cautions and Warnings
CAUTION
RISK OF ELECTRIC
SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE THE COVER.
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
CAUTION
Installation and servicing should be performed
only by qualified and experienced technicians to conform to all
local codes and to maintain your warranty.
CAUTION
Risk of explosion if Battery is replaced by an
incorrect type. Dispose of used batteries in accordance to local
laws.
Operating Notes
Power Supply
Operating Conditions
Quick Installation Guide
Avoid:
•
Viewing bright objects (for example, light fixtures), for extended periods
•
Operating or storing the unit in the following locations:
•
Extremely humid, dusty, hot/cold environments (where the operating
temperature is outside the recommended range of 14°F – 122°F
[-10°C – 50°C])
•
Close to sources of powerful electromagnetic radiation, such as radio or
TV transmitters
•
Close to fluorescent lamps or objects reflecting light
•
Under unstable light sources (might cause flickering)
Important Safeguards
•
Read and keep these instructions.
•
Please ensure that your installation area can safely support the weight of the
camera.
•
Do not install the camera in extreme temperature conditions. Only use the camera
where temperatures are within the limits shown in the Specifications section of the
User Guide. Be especially careful to provide ventilation when operating under high
temperatures.
0.2"
(6.0 mm)
•
Do not aim the camera towards an extreme light source, to prevent damaging
the imager.
Ø0.1"
(Ø3.2 mm)
•
This camera is rated for indoor operation; do not expose this camera to rain or
moisture.
•
Do not touch the camera lens, dome, or bezel (front glass plate).
•
Do not drop the camera or subject it to physical shock.
•
Do not use a strong or abrasive detergent when cleaning the camera.
1
Installing the Camera
THIS SYMBOL INDICATES THAT
DANGEROUS VOLTAGE
Before You Begin
CONSTITUTING A RISK OF
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
Before you begin, check that you have received all of the parts listed below. If any parts
are missing or damaged, contact your dealer immediately.
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND•
•
One micro dome camera
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
•
One software CD (that includes the User Guide)
•
One hardware kit
•
This Quick Installation guide
Document 800-15436V3 – Rev B – 06/2014
This micro dome camera operates on PoE.
equIP® Series 720p/1080p Indoor IP Micro Dome Camera Quick Install Guide
Installing the Camera
1.
Using the provided Allen key (see the hardware kit), loosen the screws on the
camera cover, then remove the camera cover and set aside.
Camera
cover screw
holes
MicroSDHC
card slot
2.
(Optional) Insert the microSDHC card into the card slot if you want to use a
microSDHC card to record video clips. The equIP Series IP cameras support
microSDHC cards of up to 32 GB. Push the card into the slot until it clicks into place.
To remove a microSDHC card, push it in to release it from the slot, then pull it the
rest of the way out. See
Clip Storage on MicroSDHC Card
the microSDHC card with your IP camera system.
3.
Using the provided screws (and possibly the provided, optional drywall anchors),
mount the camera on the desired ceiling or wall.
4.
Connect a CAT5 Ethernet cable to the end of the cable on the camera and then to a
Power Sourcing Equipment (PSE) such as a router or a switch.
Note
Check the status of the link indicator and the activity indicator LEDs. If these LEDs
remain unlit, please check the LAN connection.
An orange activity light (left) flashes to indicate network activity.
A steady green link light (right) indicates a good network connection.
WARNING
This product is intended to be powered by Listed ITE with
Power Over Ethernet rated 48 V DC / 300 mA.
Note
To adjust the camera's field of view, you will have to search for it on the network,
log in to it, and then view live video through the web client.
Mounting
screw holes
LEDs
Connect
to a router
or switch
for information on using
Advertisement
Related Manuals for Honeywell equIP H2S1P6X
Summary of Contents for Honeywell equIP H2S1P6X
- Page 1 To remove a microSDHC card, push it in to release it from the slot, then pull it the Thank you for purchasing a Honeywell equIP Series 720p/1080p Indoor IP Micro Dome Camera. Before installing this camera, please carefully read this guide and verify your •...
-
Page 2: Logging In To The Camera
© 2014 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice.