The use of a substitute replacement component which does Leakage 0.5mA current Device not have the same safety characteristics as the PIONEER tester under recommended replacement one, shown in the parts list in test this Service Manual, may create shock, fire, or other hazards.
Page 3
By following the instructions in this manual, be sure to apply the prescribed grease or glue to proper portions by the appropriate amount.For replacement parts or tools, the prescribed ones should be used. DVJ-X1...
Screws adjacent to mark on product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING DVJ-X1...
Page 7
DEX1013 Operating Instructions(English) DRB1358 NSP 10 Polyethylene Bag VHL-014 (230 x 340 x 0.05) • • • • • Pad (A) DHA1596 Pad (B) DHA1597 Pad (C) DHA1598 Packing Case DHG2425 Mirror mat Sheet VHL1012 SD Memory Card DWX2369 DVJ-X1...
2.5 JOG SECTION Lubricating oil ∗1 : GYA1001 27 12 ∗1 ∗1 ∗1 ∗1 Note : Be careful so that lubricating oil does not adhere to rubber section of the roller. DIPB to CN3003 ∗1 DVJ-X1...
2.6 SLOT-IN MECHANISM SECTION Lubricating oil ∗1 : GYA1001 Daifree ∗2 : GEM1036 ∗1 ∗1 ∗2 ∗2 ∗2 ∗1 DVPL to CN2001 DVPL to CN2002 DVPL to CN2003 DVJ-X1...
Page 17
DNK3911 SW Lever Spacer DEC2420 Loading Lever DNK3406 Clamper D4 Assy DXA1881 Clamper Spring DBH1374 Clamper Arm DNK3576 Eject Lever DNK3684 Lever A DNK3564 Lever B DNK3558 Guide Spring DBH1375 Disc Guide DNK3914 NSP 44 13P Spindole Flexibl Cable DVJ-X1...
3.11 MAIN ASSY (8/10) 8/10 MAIN ASSY 1/10 (DWG1570) 6/10 (S-C) (S-Y) (VD) (Cb) (Cr) Color Difference Level ADJ 1/10 1/10 6/10 1/10 2/10, 6/10 8/10 DVJ-X1...
Page 39
: Y SIGNAL ROUTE 6/10 (Cb) : Cb SIGNAL ROUTE (VD) 9/10 (AD) 9/10 1/10 (AD) : AUDIO DATA SIGNAL ROUTE 9/10 (VD) : VIDEO DATA SIGNAL BUS ROUTE : AUDIO SIGNAL ROUTE : DIGITAL OUT SIGNAL ROUTE 8/10 DVJ-X1...
Page 41
: S-VIDEO OUT Y SIGNAL ROUTE (Cr) : Cr SIGNAL ROUTE (S-Y) : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE : AUDIO SIGNAL ROUTE (Cb) : DIGITAL OUT SIGNAL ROUTE (Cr) 6/10 1/10 8/10 1/10 1/10 CN4508 2/10 2/10 1/10 CN4505 9/10 DVJ-X1...
3.14 DVPL ASSY CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. DEK1086- 466.125 MFD, BY LITTELFUSE INK. FOR IC2303. CN4507 LOADING MOTOR ASSY-S 4/10 CN701 DVJ-X1...
Page 45
DVPL ASSY (DWX2341) : ATAPI DATA SIGNAL BUS ROUTE : RF SIGNAL ROUTE : FOCUS SERVO LOOP LINE : TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE : LOADING MOTOR LOOP LINE DVJ-X1...
3.17 SLDB, LED1, LED2, CMPB, MFLB and PSWB ASSYS SLDB ASSY (DWS1347) ZERO POINT ADJ. LED1 ASSY LED2 ASSY (DWG1578) (DWG1579) CMPB ASSY (DWG1577) (Cr) (Cr) (Cb) (Cb) I J K L DVJ-X1...
Page 51
MFLB ASSY (DWG1576) CN3501 DKN1357 : VIDEO SIGNAL ROUTE PSWB ASSY (DWS1345) (Cr) : Cr SIGNAL ROUTE : Y SIGNAL ROUTE (Cb) : Cb SIGNAL ROUTE AC IN DVJ-X1...
Page 55
RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. AEK7013 MFD, BY LITTELFUSE INK. FOR IC4506. CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. AEK7014 MFD, BY LITTELFUSE INK. FOR IC4510 and IC4511. DOUT ASSY (DWG1574) DVJ-X1...
Page 63
POWER ASSY Pin No. Voltage(V) 12.0 12.3 12.3 9/10 MAIN ASSY IC1708(MN1561JF) Pin No. Voltage(V) CN4507(B4B-EH) to DVPL ASSY Pin No. Voltage(V) 12.2 CN1701(B10B-PH-SM3) CN4505(B10B-PH) to MJCB ASSY to MAIN ASSY Pin No. Voltage(V) Pin No. Voltage(V) 12.1 12.0 DVJ-X1...
Page 64
JFLB ASSY MFLB ASSY Only IC power supply Only IC power supply / GND terminal / GND terminal IC4001(UPD16306B) V3401(DEL1052) Pin No. Voltage(V) Pin No. Voltage(V) DVJ-X1...
3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram. 4. View point of PCB diagrams. Capacitor Connector SIDE A SIDE B P.C.Board Chip Part DVJ-X1...
CN4701 CN5001 CN4701 1.LPS1 (DNP2079-A) 2.GNDD 3.LPS2 CN2004 (DNP2078-A) SDCB ASSY R2510 YG-M4 R2509 R2504 CN2501 R2508 R2507 R2501 CN501 CN2502 Contact R2506 Side UP R2511 SDCB DWX2344 (DNP2076-A) C D E F T C D E F T DVJ-X1...
Page 75
(DNP2076-A) (DNP2076-A) SLMB ASSY INSW ASSY SLOTSW SLOTSW S4702 YG-M2 DWS1342 S4701 INSW CN4701 CN5001 CN4701 3.LPS2 (DNP2079-A) 2.GNDD 1.LPS1 CN2004 (DNP2078-A) SDCB ASSY S2501 DWX2344 SDCB YG-M4 (DNP2076-A) C D E F T C D E F T DVJ-X1...
4.8 PSWB and SW POWER SUPPLY ASSYS SIDE A SIDE A PSWB ASSY AN4301 DWS1345 W3152 YG-A3 LIVE PSWB C4301 W3153 W3155 DWS1349 W3154 POWER SW S4301 NEUTRAL (DNP2077-A) SW POWER SUPPLY ASSY CN101 (DWR1378) J4502 DVJ-X1...
Page 89
SIDE B SIDE B PSWB ASSY MANUAL SOLDER MANUAL SOLDER J4301 PSWB POWER SW S4301 J4301 AN4301 (DNP2077-A) SW POWER SUPPLY ASSY CN101 (DWR1378) DVJ-X1...
DWG1574 2..KSWB ASSY DWS1343 2..SLMB ASSY DWS1344 2..EJTB ASSY DWS1348 1..INSW ASSY DWS1342 > 1..SW POWER SUPPLY ASSY DWR1378 PARTS LIST OF DVJ-X1/ KUC Mark No. Description Part No. Mark No. Description Part No. MAIN ASSY IC117 M51957BFP IC305 M65774BFPA...
The position of the slide knob corresponding to TEMPO 0.00% on the FL display does Symptom of an not match "0" printed on the panel. adjustment error Adjustment Point Value of TEMPO indication Precision screwdriver (small) VR3202 VR3201 SIDE B SLDB ASSY ADIN ADCT VR3201 VR3202 DVJ-X1...
Adjust VR1501 so that the value of TP2 becomes 710mVp-p ± 2%. Procedures Symptom of an adjus Displays too dark or bright. Improper color. tment error Adjustment Point SIDE A MAIN ASSY VC1701 VR1501 VR ADJ 27MHz VR ADJ 710mV DVJ-X1...
In this mode, the version of the software program for each microcomputer can be checked. SUB 1.00 In the screen of the each software version, shows the region number on the top right of screen. DVJ-X1 SERVICE MODE 02 MAIN : Ver 1.00...
Page 100
This is displayed when a DVD other than video-formatted DVDs (VR format, DVD-A, etc.) is loaded. DISABLE DJ MODE This is displayed during DVD playback in DJ mode, while the areas that cannot be controlled in DJ mode are being played back. DVJ-X1...
Page 101
While the JOG dial is rotated in the forward direction 2 JOG While the JOG dial is rotated in the reverse direction REV indication When DIRECTION is switched to reverse When EJECT LOCK is locked EJECT LOCK indication *Mode for checking the load on the JOG dial DVJ-X1...
Page 102
Remove the screw fixing the adjust plate, then screw it into the hole corresponding to the value (-1, -2, -3, +1, or +2) for a load to be added: -1, -2, -3 : To decrease the load +1, +2 : To increase the load DVJ-X1...
Page 103
If error E11 is returned, wait a few moments then enter "IW" again. 8 Enter "EJ" to eject the disc, then turn off the power of the DVJ-X1 then turn it back on. Check that no error is displayed. DVJ-X1...
Page 104
• Start up the terminal software of the PC and set as follows: Communication speed: 4800 bps, parity: none, STOP bit: 1. • Turn on the power of the DVJ-X1 and wait until the "POWER ON" indication disappears. Then press the ENTER key on the PC several times to confirm that "R"...
Page 105
The slider is moved by about 11.1875 µm toward the innermost track. Slider Move Rev Note: This command moves a built-in player directly. Operation may become abnormal when executed this command during normal playback. Please execute this command after setting to the STOP state by all means. DVJ-X1...
Page 106
Example: To jump by 100 tracks from the current point toward outermost track: 100MF Slider Move Fwd/Rev The slider is moved by about 11.1875 µm toward the outermost/innermost track. You can move the slider to your desired position by executing this command repeatedly. DVJ-X1...
After a disc is loaded, loading Long press processing and startup processes begin. of the key In the power ON If a disc is loaded, the playback process starts. Reading data, etc. Distinction between DVD/CD CD playback DVD playback process process DVJ-X1...
Page 108
5,000 rpm. 0m01s time point Tracking balance adjustment Spindle starts Adjustment of tracking-error amplitude Searching for 30000H rotating at 3,100 rpm. Off-track threshold adjustment Measuring eccentricity Tracking on Accurate adjustment of focus position Start of acquiring addresses DVJ-X1...
7.1.3 DVJ-X1 BLOCK CHART(DJ MODE) DVD / CD SDRAM SDRAM IC2000 256M × 2 64M × 4 (AN22022A) High-speed decoding of compressed video data (MPEG2) is performed. ATAPI IC903 IC2100 IC701 IC304 (PD6449A) (MN103S72F) (PE5337A) (XCS50-5PQ208C) MPEG Video SODC DMA Controller...
Page 111
AUDIO OUT (DIGITAL) IC1513 IC1510 AUDIO OUT (PD0274A) (PCM1742KE) (2ch Analog) AQE IC Audio DAC IC503 (TE4300PF) SD Memory SD/MMC Memory Card I/F Card Controller : Video Signal Line : Audio Signal Line (DVD) : Audio Signal Line (CD) DVJ-X1...
7.1.4 DVJ-X1 BLOCK CHART(NORMAL MODE) DVD / CD SDRAM IC2000 256M × 2 (AN22022A) ATAPI IC2100 IC701 IC304 (MN103S72F) (PE5337A) (XCS50-5PQ208C) SODC DMA Controller As this chip serves as a single-chip DVD decoder and processes both video and audio signals, as with...
Page 113
IC503 (TE4300PF) SD Memory SD/MMC Memory Card I/F Card Controller Operations that are enabled using the SD Memory Card are not available in Normal mode. : Video Signal Line : Audio Signal Line (DVD) : Audio Signal Line (CD) DVJ-X1...
MAIN Assy While holding card ejector pressed, detach the control panel section. CN701 Card ejector CN501 Note: To reconnect the 40-pin flexible cable to the connector (CN701), hold the flexible cable with both hands and push it straight in. Diagnosis DVJ-X1...
Page 115
EJTB Assy MFLB Assy RSWB Assy DIPB Assy Fix the flexible cable to the lib section with a piece of lead tape R4. Lead tape R4 JFLB Assy SLDB Assy LED1 Assy JOGB Assy LED2 Assy KSWB Assy Bottom view DVJ-X1...
Page 116
Control panel section SW spring 31 SW spring 31 Bottom view Jog section Peel the sheet SW off. Unhook the upper part of the jog section. Sheet SW Exchange Lower part of the jog section Upper part of the jog section DVJ-X1...
Page 117
Remove the six screws and one flexible cable. Remove the player section. Sheet SW Jog holder 2 Mechanism holder plate Earth spring A earth spring is attached between the mechanism holder plate and the slot-in mechanism section. Be sure not to lose it. DVJ-X1...
Page 118
Remove the traverse mechanism G11 Assy-S by removing the three screws. Remove the four float spring G11s. Remove the four dampers. SPCN Assy Remove the slot-in mechanism section. Slot-in mechanism section Damper Traverse mechanism G11 Assy-S Float spring G11 DVJ-X1...
Page 119
After replacing the traverse mechanism G11 Assy-S with a new one, be sure to INSW Assy Inside SW base finish wiring of the pickup flexible cable then open those circuits by removing the solder. Bottom view Exchange Bottom view DVJ-X1...
SW POWER SUPPLY ASSY 7.1.7 CLEANING Before shipping out the product, be sure to clean the following positions by using the prescribed cleaning tools: Position to be cleaned Cleaning tools Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 DVJ-X1...
Page 122
RF input pin 2 of inside division into 4 (DVD) VCC1 Power supply pin 1 (5V) VIN3 RF input pin 3 of inside division into 4 (DVD) VIN4 RF input pin 4 of inside division into 4 (DVD) VIN1 3-beam sub (CD) input 1 DVJ-X1...
Page 123
Strobe signal for JOG FL External pull-up resistor P51 /XWRH /XBHE J_BLK Blank signal for JOG FL External pull-up resistor P50 /XWRL /XWR Not used External pull-up resistor P47 /XCS3 JOG touch sensor P46 /XCS2 Not used P45 /XCS1 Not used DVJ-X1...
Page 124
GND for A_D converter P100 /AN0 KEY0 Key input AD port − VREF Reference voltage input for A_D converter − AVcc Power supply input for A_D converter P97 /XADTRG /SIN4 Not used (set the Low to output for NC) DVJ-X1...
Page 125
Data input/output to FLASH ROM Chip enable output to FLASH ROM FADR10 FADR10 Address output to FLASH ROM Output enable to FLASH ROM MMOD MMOD Connect to VSS NRST NRST Hardware reset input − GNDD SCLOCK SCLOCK SDATA SDATA TxD/EXTRG0/MDATA DVJ-X1...
Page 126
Connect to VSS CSLFLT CSLFLT RFDIF RFDIF − AVSSC AVSSC GNDA PLFLT2 PLFLT2 Connect a capacitor for PLL PLFLT1 PLFLT1 Connect a capacitor for PLL − AVSSB AVSSB GNDA RF+ input NARF NARF RF- input VHALF VHALF Reference voltage (1.65V) input DVJ-X1...
Page 127
Interruption output to the host NIOCS16 NIOCS16 Data bus width selection Address input NPDIAG NPDIAG Address input − GNDD − VDD3 VDD3 Power supply (VD3V) Address input NCS1FX NCS1FX Chip select input NCS3FX NCS3FX Chip select input NDASP NDASP HDD15 HDD15 Data input/output DVJ-X1...
Page 128
Data input/output HDD8 HDD8 Data input/output HDD7 HDD7 Data input/output − VDDH VDDH Power supply (VD5V) NRESET NRESET Reset input from the host MASTER MASTER Connect to VSS P0/SERIAL LPS1 Loading mecha SW input P1/SERIAL LPS2 Loading mecha SW input DVJ-X1...
Page 129
44 D6 Data bus Write strobe XWE2/DQMUL − − 45 VssQ Power supply for input/output (0V) Write strobe XWE3/DQMUU − 46 D5 Data bus RDWR Read/Write − − 47 VccQ Power supply for input/output (3.3V) AUDSYNC Use with JTAG pin DVJ-X1...
Page 131
GSL expansion I/O Port Name Initial setting Function with DVJ − − − − − − SQUEEZ At squeeze: High (external pull-down) LETTER At letter: High (external pull-down) − − − − − − − − − − − − DVJ-X1...
Press to turn cue point navigation mode ON/OFF. Each time this button is pressed, the TEMPO control slider’s vari- able range changes (±6%, ±10%, ±16%, WIDE). When WIDE is selected, the variable range is +70 to –100% for DVD playback, and ±100% for CD playback. DVJ-X1...
Page 133
When indicator is not lighted, no hot cue point is recorded. 39. Title search buttons (TITLE +/–) During DVD playback, titles are forwarded or reversed in the direc- tion corresponding to the button pressed. DVJ-X1...
Page 134
Does not light in NORMAL mode. 28. Disc type indicator (DVD/CD) Lights to indicate the type of disc being played. 29. Reverse indicator (REV) Lights to indicate the Direction select switch is set to reverse (REV) position. Does not light in NORMAL mode. DVJ-X1...
34. VINYL mode indicator (Vinyl) Lights when VINYL mode is set to ON. Playing images from the DVJ-X1 on a television set The example shown here is an illustration meant to depict the general display contents, and may differ somewhat from actual monitor appearance.
* For details, consult the Operating Instructions for your recorder. 16 : 9 LB Recorded aspect ratio When playing 8cm CDs, always use an 8cm CD adapter Region number. This player can play discs This unit cannot play 8cm DVDs. marked with region “1” or “ALL”. DVJ-X1...