Advertisement
Available languages
Available languages
Table of Contents
DEH-3050UB
Printed in China
<YRD5190-A/S> ES
<KMINX> <07I00000>
Installation
English
3. Install the unit as illustrated.
Note
• Check all connections and systems before final
Mounting sleeve
Dashboard
installation.
• Do not use unauthorized parts. The use of
182
1 1 1 82
unauthorized parts may cause malfunctions.
• Consult with your dealer if installation requires
Rubber bush
53
53
drilling of holes or other modifications of the
vehicle.
• Do not install this unit where:
Screw
— it may interfere with operation of the vehicle.
— it may cause injury to a passenger as a result
of a sudden stop.
• The semiconductor laser will be damaged if it
overheats. Install this unit away from hot places
such as near the heater outlet.
Removing the Unit
• Optimum performance is obtained when the unit is
1. Extend top and bottom of the trim
installed at an angle of less than 60°.
ring outwards to remove the trim
ring. When reattaching the trim ring,
60°
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
• When installing, to ensure proper heat dispersal
fit properly.)
when using this unit, make sure you leave ample
• It becomes easy to remove the trim ring if the
space behind the rear panel and wrap any loose
front panel is released.
cables so they are not blocking the vents.
DIN Front/Rear-mount
Trim ring
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit
chassis). For details, refer to the following
installation methods.
2. Insert the supplied extraction keys
DIN Front-mount
into both sides of the unit until
they click into place.
Installation with the rubber bush
1. Insert the mounting sleeve into the
dashboard.
• When installing in a shallow space, use a
supplied mounting sleeve. If there is enough
space behind the unit, use factory supplied
mounting sleeve.
2. Secure the mounting sleeve by
using a screwdriver to bend the
metal tabs (90°) into place.
3. Pull the unit out of the dashboard.
Installation
English
DIN Rear-mount
1. Extend top and bottom of the trim
ring outwards to remove the trim
ring. When reattaching the trim ring,
push the trim ring onto the unit until
it clicks. (If the trim ring is attached
upside down, the trim ring will not
fit properly.)
• It becomes easy to remove the trim ring if the
front panel is released.
Trim ring
2. Determine the appropriate position
where the holes on the bracket and
the side of the unit match.
3. Tighten two screws on each side.
• Use either truss screws (5 mm × 8 mm)
or flush surface screws (5 mm × 9 mm),
depending on the shape of screw holes in the
bracket.
Screw
Dashboard or Console
Factory radio mounting bracket
Advertisement
Table of Contents
Related Manuals for Pioneer DEH-3050UB
Summary of Contents for Pioneer DEH-3050UB
- Page 1 • The semiconductor laser will be damaged if it overheats. Install this unit away from hot places DEH-3050UB Trim ring such as near the heater outlet. Removing the Unit • Optimum performance is obtained when the unit is 1.
-
Page 2: Instalación
Instalación Español Instalación Español Instalação Português (B) Instalação Português (B) 3. Instale la unidad como se muestra. Montaje trasero DIN 3. Apriete los dos tornillos en cada 3. Instale o aparelho como mostrado. Montagem traseira DIN 3. Aperte dois parafusos em cada Nota Nota lado. - Page 3 اﻟﻌﺮﺑﻴﺔ اﻟﱰﻛﻴﺐ DIN ﺗﺮﻛﻴﺐ ﺧﻠﻔﻲ ﺣﺴﺐ ﻣﻘﺎﻳﻴﺲ ١. ﻗﻢ ﺑﻤ ﺪ ّ أﻋﲆ وأﺳﻔﻞ ﻃﻮق اﻟﺘﻨﺠﻴﺪ ﻧﺤﻮ اﻟﺨﺎرج ﻟﻨﺰع ﻃﻮق اﻟﺘﻨﺠﻴﺪ. ﻋﻨﺪ إﻋﺎدة ﺗﺮﻛﻴﺐ ﻃﻮق 1 1 1 82 اﻟﺘﻨﺠﻴﺪ، ادﻓﻊ ﻃﻮق اﻟﺘﻨﺠﻴﺪ ﰲ اﻟﻮﺣﺪة إﱃ أن 1 1 1 82 ﻳﻨﻄﺒﻖ...
-
Page 4: Connection Scheme
1. This product 1. This product 26. Power amp 2. Rear output or (sold separately) subwoofer output 6. AUX jack (3.5 φ) 31. Subwoofer output 23. To rear output or 6. AUX jack (3.5 φ) subwoofer output Use a stereo mini plug 3. -
Page 5: Connecting The Units
Connecting the units English Connecting the units English Conexión de las unidades Español Conexión de las unidades Español Connection Diagram Diagrama de conexión • Control signal is output through blue/white cable • La señal de control se emite a través del cable Note Nota when this unit is powered on. -
Page 6: Conexão Dos Componentes
Conexão dos componentes Português (B) Conexão dos componentes Português (B) Diagrama de conexão • O sinal de controle é emitido através do cabo azul/ Nota branco quando este aparelho é ligado. Conecte-o a um terminal de controle remoto de sistema de •... - Page 7 اﻟﻌﺮﺑﻴﺔ ﺗﻮﺻﻴﻞ اﻟﻮﺣﺪات اﻟﻌﺮﺑﻴﺔ ﺗﻮﺻﻴﻞ اﻟﻮﺣﺪات ﻣﺨﻄﻂ اﻟﺘﻮﺻﻴﻞ ﻣﻼﺣﻈﺔ –32 ﻋﻨﺪﻣﺎ ﻻ ﻳﻜﻮن ﺳﻠﻚ اﻟﺴﻤﺎﻋﺔ اﻟﺨﻠﻔﻴﺔ ﻣﺘﺼﻼ (١ ﺑﻤﺠﻬﺎر اﻟﱰددات اﻟﺨﻔﻴﻀﺔ اﻟﻔﺮﻋﻲ )اﻟﺸﻜﻞ ﻋﻨﺪ اﺳﺘﺨﺪام ﻣﺠﻬﺎر اﻟﱰددات اﻟﺨﻔﻴﻀﺔ اﻟﻔﺮﻋﻲ –33 ﺑﺪون اﺳﺘﺨﺪام ﻣﻀﺨﻢ اﻟﺼﻮت اﻻﺧﺘﻴﺎري –34 (٢ )اﻟﺸﻜﻞ –1 –2 –3 –35 –4...