Front Panel ........................8 Back Panel ........................9 Connecting the Receiver ....................10 ISB7005 Wireless Network Connection .................11 Connecting the Wireless Access Point to the Wireless Gateway ........12 Pairing the Wireless Access Point and Receiver ............12 Connections for a High-Defi nition TV (HDTV) ..............13 Connections for a Standard-Defi nition TV (SDTV) ............14...
Notice for Installers The servicing instructions in this notice are for use by qualifi ed service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualifi ed to do so.
Page 5
IMPORTANT SAFETY INSTRUCTIONS, continued Service Warnings Verify the Power Source from the On/Off Power Light When the on/off power light is not illuminated, the apparatus may WARNING: Avoid electric shock! Do not open still be connected to the power source. The light may go out when the cover of this product.
Change the Way You Watch TV Welcome to U-verse TV. The ISB7005 devices, known as U-verse receivers, bring a rich, new set of interactive services directly to you through your TV and your in-home IP network. The receiver uses wireless technology 802.11n to connect to the network.
Turns the receiver on or places it in standby. To restart the receiver, press and hold the POWER button for 10 seconds. The LED is green 2 Model Number Identifi es the model number of your receiver as ISB7005 3 Signal Strength Identifi es the strength of the wireless connection...
Back Panel TO TV (VIDEO OUT) OPTICAL POWER VIDEO AUDIO S-VIDEO NETWORK T14821 T14821 1 To TV (Video Out) Connect to TV. You must set the channel on your TV to the channel designated by your service provider (usually channel 3). Contact your service provider for the channel information 2 Network Connect to the Ethernet (CAT-5) network at your home, if applicable...
Connecting the Receiver To connect your receiver to your network and home entertainment devices, complete these steps. Because the connections for a high-defi nition (HD) or standard-defi nition (SD) TV are diff erent, you must determine if your TV is HD or SD.
ISB7005 Wireless Network Connection PO WER LINK The ISB7005 receiver allows for easy and secure connection to U-verse services. The signal strength 7005 indicator on the front panel of the receiver identifi es the strength of the wireless connection and aids in the proper placement of the receiver.
Connecting the Wireless Access Point to the Wireless Gateway RJ-45 Wireless 1. Connect the 12 VDC Power Supply Cable Gateway plug on the access point to the wall Ethernet Port power outlet. Use only the power adapter provided with the product. Reset 2.
Connections for a High-Defi nition TV (HDTV) To use the receiver with an HDTV, you must make one of the following connections to view the HD content. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed connection information.
Connections for a Standard-Defi nition TV (SDTV) When using the receiver with an SDTV, you must make one of the following connections to view content. Some SDTVs may not have all these connections. Refer to the owner’s manual for your TV and the cabling diagrams in this manual for more detailed information.
Connections for a VCR or DVD Recorder When using the receiver with a VCR or DVD recorder, you must make one of the following connections to view content. Although all connections provide you with quality service, we list the connections in our recommended order.
Connecting to an HDTV with an HDMI Connector Cable Used in this Confi guration • 1 HDMI Cable Notes: • The HDMI port on the TV must support high-bandwidth digital content protection (HDCP). • The HDMI interface supports Dolby ™ Digital 5.1 audio.
Connecting to an HDTV with a DVI Connector Cables Used in this Confi guration • 1 HDMI-to-DVI Cable or 1 HDMI Cable and 1 HDMI-to-DVI Adapter • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s capabilities.) Notes:...
Connecting to an HDTV with Component (YPbPr) Connectors Cables Used in this Confi guration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram, dependent upon your TV’s capabilities.) WARNING: Electric shock hazard! Unplug all electronic devices before connecting or...
Connecting to an SDTV with Component (YPbPr) Connectors Cables Used in this Confi guration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable Note: The receiver must be set to the proper standard-defi nition mode. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to an SDTV with an S-Video Connector Cables Used in this Confi guration • 1 S-Video Cable • 1 Audio Left/Right Cable WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver. Receiver TO TV (VIDEO OUT)
Connecting to an SDTV with an RCA-Type Connector Cables Used in this Confi guration • 1 RCA-type Video Cable • 1 Audio Left/Right Cable WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver. Receiver TO TV (VIDEO OUT)
Connecting to an SDTV with a Coaxial Cable Cable Used in this Confi guration • 1 Coaxial Cable Note: You must set the channel on your TV to the channel designated by your service provider (usually channel 3). Contact your service provider for the channel information. WARNING: Electric shock hazard! Unplug all electronic devices before connecting or disconnecting any device cables to the receiver.
Connecting to a Home Theater System with Component (YPbPr) Connectors Cables Used in this Confi guration • 1 Component Video Cable (YPbPr) • 1 Audio Left/Right Cable (You can also use an optical cable [indicated by the dotted line] instead of the Audio Left/Right Cable as shown in the diagram.) Notes: •...
Connecting to a Stereo VCR or DVD Recorder (optional) The diagram below shows how to connect a recording device to your receiver. Although it is possible to watch TV using a connection through your VCR or DVD recorder to the TV, this connection may not provide the best picture, and HDTV users are restricted to an SD format.
Troubleshooting If the receiver does not perform as expected, the following tips may help. If you need further assistance, contact your service provider. No Picture • Verify that the power to your TV is turned on. • Verify that your wireless receiver and wireless access point are powered on. •...
Frequently Asked Questions What Is Digital Television? Digital television (DTV) is a huge leap forward in television technology compared to analog television that has been widely available since the 1940s. DTV is delivered and displayed using digital encoding, similar to the way a PC operates. By using digital technology, there is no variation in picture and sound quality from the origination point until it is displayed on your television.
Picture Formats What Is the Diff erence Between a Standard-Screen and a Wide-Screen HDTV? The type of screen your HDTV has (wide-screen or standard-screen) determines how the receiver displays programs on the screen. The picture format for an HDTV is a combination of aspect ratio and screen resolution and is diff erent for standard-screen and wide-screen HDTVs.
Index AC Power input DC Power output Arrow keys Diagrams. See Connecting the receiver to other devices Aspect ratio Digital Video Recorder. See DVR Audio Out 9, 13, 14, 15 Digital TV, What is it DVD Connection 9, 10, 15, 24 Back panel DVI connector 13, 17...
Page 29
Index, continued Picture formats USB port 8, 9 Ports. See Connectors Power 8, 9 VCR connection 9, 15, 24 Programs, view Video Out. See To TV Progressive screen resolution View programs RGB connector 13, 25 Wide-screen TV S-Video Out 9, 14, 15 YPbPr S-Video In 14, 15...
Cisco and the Cisco logo are trademarks or registered trademarks FCC Declaration of Conformity of Cisco and/or its affi liates in the U.S. and other countries. A listing of Cisco’s trademarks can be found at www.cisco.com/go/ This device complies with Part 15 of FCC Rules. Operation is trademarks.
Page 31
(2009) limits. The evaluation was based on evaluation per RSS-102 Rev 4. The minimum separation distance from the antenna to general bystander is 7.9 inches (20cm) to maintain compliance. Note: The ISB7005 has disabled the 5600-5650M band by S/W to avoid 5600-5650M band for IC certifi cation.