hit counter script
Cisco Aironet 1400 Series Hardware Installation Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Wireless Access Point
  5. Aironet 1400 Series
  6. Hardware installation manual
Cisco Aironet 1400 Series Hardware Installation Manual

Cisco Aironet 1400 Series Hardware Installation Manual

Hide thumbs Also See for Aironet 1400 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Cisco Aironet 1400 Series Wireless Bridge
Hardware Installation Guide
August 2006
Corporate Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 526-4100
Text Part Number: OL-4072-04

Advertisement

Chapters

Table of Contents
loading

Related Manuals for Cisco Aironet 1400 Series

Summary of Contents for Cisco Aironet 1400 Series

  • Page 1 Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide August 2006 Corporate Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 526-4100 Text Part Number: OL-4072-04...
  • Page 2 You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures: •...

  • Page 3: Table Of Contents

    Key Features Power External Antenna Integrated Antenna Ethernet Ports Metal Enclosure Bridge LEDs Receive Signal Strength Indicator Port Network Configuration Examples Point-to-Point Configuration Port Aggregation or Redundancy Configuration Point-to-Multipoint Configuration Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 4 Configuring the Bridge for the First Time C H A P T E R Before You Start Resetting the Bridge to Default Settings Obtaining and Assigning an IP Address Connecting to the Bridge Locally Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 5 Obtaining the TFTP Server Software 6-12 Translated Safety Warnings A P P E N D I X Warning Definition Installation Warning Installation and Grounding Warning Circuit Breaker Warning Ground Conductor Warning Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 6 Assembling the Rooftop or Wall Mount A P P E N D I X Overview Unpacking the Mount Package Contents Assembling the Mount L O S S A R Y N D E X Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 7: Preface

    Series Wireless Bridge Hardware Installation Guide. OL-4072-03. Objectives This publication explains the steps for initial setup and basic configuration of the Cisco Aironet 1400 Series Wireless Bridge (hereafter called the bridge) supporting 5.8-GHz operation. This publication also provides troubleshooting information and detailed specifications.

  • Page 8: Conventions

    électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » (Traduction des avis de sécurité). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 viii OL-4072-04...

  • Page 9: Related Publications

    This document is available on the Cisco CCO web site at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/wireless/index.htm Cisco Aironet 1400 Series Wireless Bridge Mounting Instructions that was shipped with your bridge • provides detailed instructions for mounting the bridge and aligning the antenna .

  • Page 10: Obtaining Documentation

    Cisco Secure Access Control Server for Windows 2000/NT Servers Version 3.0 User Guide provides • complete instructions for using Cisco Secure ACS, including steps for configuring Cisco Secure ACS to support access points and bridges. This document is available on the Cisco CCO web site at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_soft/csacs4nt/csnt30/user/index.htm Obtaining Documentation Cisco documentation and additional literature are available on Cisco.com.

  • Page 11: Ordering Documentation

    Reporting Security Problems in Cisco Products Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT: •...

  • Page 12: Product Alerts And Field Notices

    Modifications to or updates about Cisco products are announced in Cisco Product Alerts and Cisco Field Notices. You can receive Cisco Product Alerts and Cisco Field Notices by using the Product Alert Tool on Cisco.com. This tool enables you to create a profile and choose those products for which you want to receive information.

  • Page 13: Submitting A Service Request

    Cisco engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

  • Page 14: Definitions Of Service Request Severity

    Cisco products that are sold through channel partners. It is updated twice a year and includes the latest Cisco channel product offerings. To order and find out more about the Cisco Product Quick Reference Guide, go to this URL: http://www.cisco.com/go/guide...
  • Page 15 Preface Obtaining Additional Publications and Information Networking products offered by Cisco Systems, as well as customer support services, can be • obtained at this URL: http://www.cisco.com/en/US/products/index.html Networking Professionals Connection is an interactive website where networking professionals • share questions, suggestions, and information about networking products and technologies with Cisco experts and other networking professionals.
  • Page 16 Preface Obtaining Additional Publications and Information Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 17: Chapter 1 Overview

    C H A P T E R Overview The Cisco Aironet 1400 Series Wireless Bridge (hereafter called the bridge) is a wireless device designed for building-to-building wireless connectivity. Operating in the 5.8-GHz UNII 3 band (5725 to 5825 MHz), derived from the 802.11a standard, the bridge delivers 6 to 54 Mbps data rates without the need for a license.

  • Page 18: Key Features

    Note The bridge communicates only with other bridges and does not support associations with wireless client adapters. Figure 1-1 Bridge Configurations Integrated antenna bridge configuration External antenna bridge configuration Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 19: Power

    The bridge receives inline power from the Cisco Aironet Power Injector LR (hereafter called the power injector). Dual-coax cables are used to provide Ethernet data and power from the power injector to the bridge.

  • Page 20: Integrated Antenna

    Metal Enclosure The bridge uses a metal enclosure that supports outdoor operating environments and supports an industrial temperature operating range (refer to “Bridge Specifications” section on page 1-8). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 21: Bridge Leds

    • associated with another bridge. Steady green indicates that the bridge is associated with at least one other bridge. This LED also provides signal strength readings during installation mode. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 22: Receive Signal Strength Indicator Port

    1-3). The bridge connected to the main LAN network is classified as a root bridge and the other bridge is classified as a repeater bridge. Figure 1-3 Point-to-Point Bridge Configuration Bridge Bridge Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 23: Port Aggregation Or Redundancy Configuration

    Bridge Bridge Bridge Bridge Point-to-Multipoint Configuration The point-to-multipoint configuration (Figure 1-5) connects the main LAN network to multiple remote LAN networks. Figure 1-5 Point-to-Multipoint Bridge Configuration Bridge Bridge Bridge Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 24: Bridge Specifications

    NEMA Type 4 (IP56) enclosure rating. External antenna configuration: The enclosure has been successfully tested and is in compliance with a NEMA Type 4 (IP56) enclosure rating. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 25 Antenna Integrated antenna — (Depending on the 22.5-dBi patch array regulatory region) 20-dBi patch array External antennas: 9-dBi omnidirectional 9.5-dBi sector 28-dBi dish (Depending on the regulatory region) Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 26: Maximum Power Levels

    This restricts the bridge output power that can be used with the bridge antennas and affects the resulting operating range of the bridge (for additional information refer to Appendix C, “Channels and Maximum Power Levels.” Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 1-10 OL-4072-04...

  • Page 27: Installation Overview

    This chapter includes the following sections: Warnings, page 2-2 • Safety Information, page 2-3 • • Unpacking the Bridge, page 2-5 Before Beginning the Installation, page 2-6 • • Installation Summary, page 2-9 Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 28: Chapter 2 Installation Overview

    In order to comply with radio frequency (RF) exposure limits, the antennas for this product should be positioned no less than 6.56 ft (2 m) from your body or nearby persons. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 29: Safety Information

    FCC-certified equipment. When used with approved Cisco Aironet antennas, Cisco Aironet products meet the uncontrolled environmental limits found in OET-65 and ANSI C95.1, 1991. Proper operation of this radio device according to the instructions in this publication results in user exposure substantially below the FCC recommended limits.

  • Page 30: Typical Bridge Installation Components

    (U.S.); Canadian Electrical Code, Part I, CSA 22.1 (Canada); and if local or national electrical codes are not available, refer to IEC 364, Part 1 through 7 (other countries). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 31: Installation Guidelines

    Ensure that all items listed in the “Package Contents” section are included in the shipment. If any item Step 3 is damaged or missing, notify your authorized Cisco sales representative. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 32: Package Contents

    Bridge Installation diagram (Figure 2-1) • Bridge layout (Figure 2-2) • Power injector layout (Figure 2-3) • Power module (Figure 2-4) • Grounding block (Figure 2-5) • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 33 Installation Overview Before Beginning the Installation Figure 2-2 Bridge Layout and Connectors Bridge mounting brackets RSSI voltage port (female BNC connector) Bridge LED indicators Power injector dual-coax ports (F-type connectors) Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 34 Mode button Power LED indicator Ethernet port (RJ-45 connector) Power injector dual-coax ports (F-Type connectors) Indicator LEDs Figure 2-4 Power Module 48-VDC power output cable AC power cord Power module Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 35: Installation Summary

    Note Connect a ground wire to the grounding block. • Mount the bridge to the external tower or mast. For additional information, refer to the Cisco Aironet • 1400 Series Wireless Bridge Mounting Instructions that shipped with your bridge. Connect a ground wire to the bridge (use the bridge ground lug).
  • Page 36 Connect the power module to the power injector and plug the AC cord into an AC power receptacle. • Align the bridge antenna. For additional information, refer to the Cisco Aironet 1400 Series Wireless • Bridge Mounting Instructions that shipped with your bridge.
  • Page 37 Mounting Hardware, page 3-2 • • Bridge LEDs, page 3-3 Aligning the Antenna Using LED Indications, page 3-5 • • Aligning the Antenna Using the RSSI Voltage, page 3-6 Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 38: Chapter 3 Mounting And Alignment Overview

    Typically, the bridge is installed on a rooftop, mast, tower, wall, or a suitable flat surface. Each of these installations requires a different approach. This document provides a mounting overview. For detailed mounting instructions, refer to the Cisco Aironet 1400 Series Wireless Bridge Mounting Instructions that shipped with your bridge.

  • Page 39: Bridge Brackets

    The LEDs are mounted on the back of the housing near the connectors (see Figure 3-1). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 40 Green blinking Root, searching Not associated (root mode). The bridge attempts to associate with a non-root bridge indefinitely. Green Root, associated Associated (root mode). 1. Preconfigured bridges search indefinitely. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 41: Aligning The Antenna Using Led Indications

    Medium blink –75 to –72 Slow blink < –75 1. Slow blinking rate of 1 blink/sec. 2. Medium blinking rate of 2 blinks/sec. 3. Fast blinking rate of 4 blinks/sec. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 42: Aligning The Antenna Using The Rssi Voltage

    ± 4 dB. To obtain RSSI readings, you can use any convenient voltmeter connected to the RSSI port using a cable with a male BNC connector. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 43: Choosing A Second Mounting Location

    This chapter contains the following topics: Overview, page 4-2 • Choosing a Second Mounting Location, page 4-2 • • Installing the Stacked Bridges, page 4-2 Verifying Isolation, page 4-3 • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 44: Overview

    You can double the throughput, or create a standby link, by stacking two bridges. A stacked installation consists of two bridge systems installed at the same physical location. For detailed mounting instructions refer to the Cisco Aironet 1400 Series Wireless Bridge Mounting Instructions that shipped with your bridge.

  • Page 45: Verifying Isolation

    Connect a voltmeter to the RSSI port of bridge D and verify that the voltage is 1.95 V (–40 dBm) or less. If the voltage exceeds 1.95 V, move the bridge farther away and repeat this step. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 46 After you verify the isolation of the second bridge link, you must properly set the root and non-root Step 5 bridge settings for both links, align the link 2 bridge antennas, and verify proper link 2 operation. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 47 Using the IP Setup Utility, page 5-9 • • Assigning an IP Address Using the CLI, page 5-12 Using a Telnet Session to Access the CLI, page 5-12 • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 48: Chapter 5 Configuring The Bridge For The First Time

    Enter your username in the User Name field. The default username is Cisco. Step 3 Enter the bridge password in the Password field and press Enter. The default password is Cisco. The Step 4 Summary Status page appears.

  • Page 49: Obtaining And Assigning An Ip Address

    IP address. The bridge’s MAC address is on label attached to the bottom of the bridge. Use the Cisco IP Setup Utility (IPSU) to identify the assigned address. You can also use IPSU – to assign an IP address to the bridge if it did not receive an IP address from the DHCP server.

  • Page 50: Assigning Basic Settings

    Step 2 screen appears. Press Tab to bypass the Username field and advance to the Password field. Step 3 Enter the case-sensitive password Cisco and press Enter. The Summary Status page appears. Figure 5-1 Step 4 shows the Summary Status page.
  • Page 51 Assigning Basic Settings Figure 5-1 Summary Status Page Click Express Setup. The Express Setup screen appears. Figure 5-2 shows the Express Setup page. Step 5 Figure 5-2 Express Setup Page Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 52 No—Remote bridges must specify an SSID to associate with the bridge. With No selected, the – SSID used by the remote bridge must match exactly the bridge’s SSID. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 53 You can restore the bridge to its factory defaults by unplugging the power injector’s power jack Note and plugging it back in while holding down the Mode button for a few seconds, or until the Status LED turns amber. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 54: Default Settings On The Express Setup Page

    When bridges are installed less than 328 ft (100 m) apart, you should reduce their output power to • avoid overloading the bridge’s receivers. To configure your bridge’s output power level, refer to the Cisco Aironet 1400 Series Wireless Bridge Software Configuration Guide. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03...

  • Page 55: Protecting Your Wireless Lan

    IP address and the SSID. Obtaining and Installing IPSU IPSU is available on the Cisco web site. Follow these steps to obtain and install IPSU: Use your web browser to go to the Cisco Software Center at the following URL: Step 1 http://www.cisco.com/cisco/software/navigator.html...

  • Page 56: Using Ipsu To Find The Bridge's Ip Address

    DHCP-assigned IP address. To change the bridge IP address from the default value using IPSU, refer to “Using IPSU to Set the Bridge’s IP Address and SSID” section on page 5-11. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 5-10 OL-4072-04...

  • Page 57: Using Ipsu To Set The Bridge's Ip Address And Ssid

    Enter the SSID you want to assign to the bridge in the SSID field. Step 5 Note You cannot set the SSID without also setting the IP address. However, you can set the IP address without setting the SSID. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 5-11 OL-4072-04...

  • Page 58: Assigning An Ip Address Using The Cli

    Note session in Windows 2000, type open followed by the bridge’s IP address. Step 3 In the Host Name field, type the bridge’s IP address and click Connect. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 5-12 OL-4072-04...
  • Page 59 C H A P T E R Troubleshooting This chapter provides troubleshooting procedures for basic problems with the bridge. For the most up-to-date, detailed troubleshooting information, refer to the Cisco TAC website at the following URL (select Hardware Support > Wireless Devices): http://www.cisco.com/tac...

  • Page 60: Troubleshooting

    During bridge operation the LEDs provide status information as shown in Table 6-1. Table 6-1 Bridge Normal Mode LED Indications Ethernet Status Radio Meaning — — Ethernet link is down or disabled. Green — — Ethernet link is operational. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 61 If the problem continues, contact technical support for assistance. — — Amber Radio firmware error—disconnect and reconnect power injector power.If the problem continues, contact technical support for assistance. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 62: Power Injector Leds

    When power is applied to the bridge, the bridge activates the bootloader and begins the POST operations. The bridge begins to load the IOS image when the Post operations are successfully completed. Upon successfully loading the IOS image, the bridge initializes and tests the radio. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 63 If the cables are connected correctly, contact technical support for assistance. Green — — Link between power injector and bridge is operational. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 64: Checking Power

    AC receptacle and that AC power is available. Uplink Activity LED • Green or blinking green color indicates the bridge is operating. – Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 65: Checking Basic Configuration Settings

    Check (MIC), WEP key hashing, and 802.1X protocol versions. If a non-root bridge is unable to authenticate to your root bridge, verify that the security settings are the same as your bridge settings. For additional information, refer to the Cisco Aironet 1400 Series Wireless Bridge Software Configuration Guide.

  • Page 66: Antenna Alignment

    To meet regulatory restrictions, the external antenna bridge configuration and the external antenna must Note be professionally installed. For detailed alignment instructions, refer to the Cisco Aironet 1400 Series Wireless Bridge Mounting Instructions that shipped with your bridge. Resetting to the Default Configuration If you forget the password that allows you to configure the bridge, you may need to completely reset the configuration.

  • Page 67: Using The Web Browser Interface

    Follow the steps below to reload the bridge image file: The PC you intend to use must be configured with a static IP address in the range of 10.0.0.2 to 10.0.0.30. Step 1 Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 68: Web Browser Interface

    Click Browse to locate the image file on your PC. Step 6 Click Upload. Step 7 For additional information, click the Help icon on the Software Upgrade screen. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 6-10 OL-4072-04...

  • Page 69: Browser Tftp Interface

    For additional information click the Help icon on the Software Upgrade screen. Obtaining the Bridge Image File You can obtain the bridge image file from the Cisco.com software center by following these steps: Use your web browser to go to the Cisco Software Center at the following URL: Step 1 http://www.cisco.com/cisco/software/navigator.html...

  • Page 70: Obtaining The Tftp Server Software

    Troubleshooting Reloading the Bridge Image Obtaining the TFTP Server Software You can download TFTP server software from several web sites. Cisco recommends the shareware TFTP utility available at this URL: http://tftpd32.jounin.net Follow the instructions on the website for installing and using the utility.

  • Page 71: Appendix

    Installation Warning, page A-9 • • Lightning Activity Warning, page A-10 Explosive Device Proximity Warning, page A-11 • • Radio Frequency Exposure Limits, page A-11 Restricted Area Warning, page A-12 • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 72: Warning Definition

    (Para ver as traduções dos avisos que constam desta publicação, consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos de Segurança”). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 73: Installation Warning

    ¡Advertencia! Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo. Varning! Endast utbildad och kvalificerad personal bör få tillåtelse att installera, byta ut eller reparera denna utrustning. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 74: Installation And Grounding Warning

    Pour une installation et mise à la terre correctes de l'antenne, veuillez consulter les codes nationaux et locaux (par exemple, États-Unis : NFPA 70, National Electrical Code, Article 810 ; Canada : Code électrique canadien, Section 54). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 75 För riktig installation och jordning av antennen, hänvisas du till nationella och lokala koder (t.ex. USA: NFPA 70, National Electrical Code, Article 810, Kanada: Canadian Electrical Code, Section 54). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 76: Circuit Breaker Warning

    A termék védelmi rendszerének része az épület kábelezésébe épített rövidzárlat (túláram) elleni védelem is. Gondoskodjon róla, hogy a készüléket védõ eszköz legfeljebb 120 VAC, 15A U.S. (240 VAC, 10A International) áramerõsségre legyen méretezve. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 77: Ground Conductor Warning

    Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 78 Denna utrustning måste jordas. Koppla aldrig från jordledningen och använd aldrig utrustningen utan en på lämpligt sätt installerad jordledning. Om det föreligger osäkerhet huruvida lämplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 79: Installation Warning

    Leia as instruções de instalação antes de ligar o sistema à fonte de energia. ¡Advertencia! Lea las instrucciones de instalación antes de conectar el sistema a la red de alimentación. Varning! Läs installationsanvisningarna innan du kopplar systemet till strömförsörjningsenheten. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 80: Lightning Activity Warning

    No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas eléctricas en la atmósfera. Varning! Vid åska skall du aldrig utföra arbete på systemet eller ansluta eller koppla loss kablar. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 A-10 OL-4072-04...

  • Page 81: Explosive Device Proximity Warning

    Waarschuwing De antennes van dit product moeten minimaal 2 m van u of andere personen zijn verwijderd om te voldoen aan de vereisten voor blootstelling aan radiofrequenties (RF). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 A-11 OL-4072-04...

  • Page 82: Restricted Area Warning

    Tämä laite on tarkoitettu asennettavaksi paikkaan, johon pääsy on rajoitettua. Tällaiseen paikkaan Varoitus pääsee vain erikoistyökalua, lukkoon sopivaa avainta tai jotakin muuta turvalaitetta käyttämällä. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 A-12 OL-4072-04...
  • Page 83 Denna enhet är avsedd för installation i områden med begränsat tillträde. Ett område med begränsat tillträde kan endast tillträdas med hjälp av specialverktyg, lås och nyckel eller annan säkerhetsanordning. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 A-13 OL-4072-04...
  • Page 84 Appendix A Translated Safety Warnings Restricted Area Warning Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 A-14 OL-4072-04...

  • Page 85: Appendix

    A P P E N D I X Declarations of Conformity and Regulatory Information This appendix provides declarations of conformity and regulatory information for the Cisco Aironet 1400 Series Wireless Bridge. This appendix contains the following sections: Manufacturers Federal Communication Commission Declaration of Conformity Statement, page •...

  • Page 86: Manufacturers Federal Communication Commission Declaration Of Conformity Statement

    Table B-1. Any changes or modification to the product not expressly approved by Cisco could void the user’s authority to operate this device. Caution To meet regulatory restrictions, the bridge with the antenna connector and the external antenna must be be professionally installed.

  • Page 87: Canadian Compliance Statement

    This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation. Cisco’s 54-Mbps, 5.8-GHz bridges are certified to the requirements of RSS-210 issue 5, RSP 100, and RSS 102 for 5-GHz spread spectrum devices. International Models...

  • Page 88: European Community: Ireland

    For 54 Mbps, 5.8 GHz radio bridge being sold in Ireland, the following standards were applied: Radio: No harmonized standard currently exists. Radio spectrum matters covered in TCF as per • R&TTE Directive 99/5/EC. EMC: EN 301.489-1, EN 301.489-4 • Safety: EN 60950 • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 89: Declaration Of Conformity For Rf Exposure

    This bridge is also compliant to EN 50835 for RF exposure. This transmitter may not be co-located or operating in conjunction with other transmitters or antennas separated by less than 6.56 feet (2 meters). Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 90: Administrative Rules For Cisco Aironet Bridges In Taiwan

    Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 91: Operation Of Cisco Aironet Bridges In Brazil

    (ISM) equipment, or by an incidental radiator. Operation of Cisco Aironet Bridges in Brazil This section contains special information for operation of Cisco Aironet bridges in Brazil. Bridge Model AIR-BR1410A-A-K9-N...

  • Page 92: Portuguese Translation

    This equipment operates on a secondary basis and consequently must accept harmful interference, including interference from stations of the same kind. This equipment may not cause harmful interference to systems operating on a primary basis. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 93: Appendix

    Channels and Maximum Power Levels For channel and maximum power level settings, refer to the Channels and Maximum Power Settings for Cisco Aironet Autonomous Access Points and Bridges document available on the Cisco Wireless documentation page of Cisco.com. To browse to the document, follow these steps:...
  • Page 94 Appendix C Channels and Maximum Power Levels Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 95: Appendix

    This appendix provides assembly instructions for the optional rooftop or wall mount and contains the following sections: Overview, page D-2 • Unpacking the Mount, page D-2 • • Package Contents, page D-2 Assembling the Mount, page D-3 • Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 96: Overview

    Mounting hardware consisting of the following: • One long flanged hex bolt [2 in. (5.08 cm)] – Two carriage bolts [0.5 in. (1.27 cm)] – – Four washers – Three flanged hex nuts Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...

  • Page 97: Assembling The Mount

    Step 9 Place a washer and hex nut on the end of the carriage bolt and hand-tighten. Repeat Steps 8 and 9 for the other square hole. Step 10 Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 OL-4072-04...
  • Page 98 You must securely attach the mounting plate to the wall or roof and tighten all nuts (12 to 14 ft-lb). Note To mount your rooftop or wall mount, please follow the mounting instructions located in the Cisco Aironet 1400 Series Wireless Bridge Mounting Instructions that shipped with your bridge.

  • Page 99: G L O S S A R Y

    The size of the cell depends upon the speed of the transmission, the type of antenna used, and the physical environment, as well as other factors. Carrier sense multiple access. A wireless LAN media access method specified by the IEEE 802.11 CSMA specification. Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-1 OL-4072-04...
  • Page 100 A repository for files from which a local area network can share files, mail, and programs. file server Software that is programmed on a memory chip. firmware Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-2 OL-4072-04...
  • Page 101 A modulation technique used by IEEE 802.11a-compliant wireless LANs for transmission at 6, 9, Orthogonal Frequency 12, 18, 24, 36, 48, and 54 Mbps. Division Multiplex (OFDM) Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-3 OL-4072-04...
  • Page 102 UNII-2 Regulations for UNII devices operating in the 5.725 to 5.825 GHz frequency band. UNII-3 A single data message (packet) sent to a specific IP address. unicast packet Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-4 OL-4072-04...
  • Page 103 Wired Equivalent Privacy. An optional security mechanism defined within the 802.11 standard designed to make the link integrity of wireless devices equal to that of a cable. A computing device with an installed client adapter. workstation Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-5 OL-4072-04...
  • Page 104 Glossary Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 GL-6 OL-4072-04...

  • Page 105: I N D E X

    A-3 related publications obtaining documentation operating temperature environmental conditions package contents 2-6, D-2 password reset power Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 IN-1 OL-4072-04...
  • Page 106 RF exposure safety warnings, translated site survey size specifications SSID, troubleshooting Telnet 5-12 temperature, operating TFTP server troubleshooting unpacking warning, defined viii to ix warnings 2-2, A-1 weight Cisco Aironet 1400 Series Wireless Bridge Hardware Installation Guide. OL-4072-03 IN-2 OL-4072-04...

Table of Contents