hit counter script
Husqvarna 325HE3 X-series Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 325HE3 X-series
  6. Operator's manual
Husqvarna 325HE3 X-series Operator's Manual

Husqvarna 325HE3 X-series Operator's Manual

Hide thumbs Also See for 325HE3 X-series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operator's Manual
325HE3
325HE4
Please read the operator's manual carefully and make sure you understand the instructions
Operator's manual
X-series
X-series
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 325HE3 X-series

Summary of Contents for Husqvarna 325HE3 X-series

  • Page 1 Operator′s manual 325HE3 X-series 325HE4 X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols WARNING! Incorrect or careless Keep all parts of your body away from use of a hedge trimmer can turn it hot surfaces. into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............2 Please read the operator’s manual carefully. CONTENTS Contents ............... 3 WARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ......3 impairment.

  • Page 4: Introduction

    Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production of muskets.

  • Page 5: What Is What

    WHAT IS WHAT? What is what? Cutter 15 Cylinder cover Bevel gear 16 Spark plug cap and spark plug Shaft 17 Fuel tank Hand guard (325HE3) 18 Starter handle Hand guard mounting screw (325HE3) 19 Impact guard (325HE4) Front handle (325HE3) 20 Angle adjustment handle Angle adjustment knob 21 Grease nipple and plug for filling lubricant.

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for cutting branches and Incorrect or careless use of a hedge trimmer can turn it twigs. into a dangerous tool that can cause serious or even fatal injury.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS CLOTHING the throttle control is automatically locked at the idle setting. Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot.
  • Page 8 GENERAL SAFETY PRECAUTIONS Stop switch Regularly check the vibration damping units for cracks or deformation. Check that the vibration damping element is Use the stop switch to switch off the engine. undamaged and securely attached. WARNING! Overexposure to vibration can lead to circulatory damage or nerve damage in people who have impaired circulation.
  • Page 9 GENERAL SAFETY PRECAUTIONS Regularly check that the muffler is securely attached to Blades the machine. To ensure good cutting results it is important that the contact pressure between the blades is correct. The contact pressure is adjusted by turning the screws on the underside of the bar clockwise as far as they will go.

  • Page 10: Assembly

    ASSEMBLY Fitting the hand guard and loop Adjusting the harness handle (325HE4) (325HE3) You should always use the harness with the machine to give maximum control over the machine and reduce the Slide the spacer into the slot in the loop handle. risk of fatigue in your arms and back.

  • Page 11: Fuel Handling

    Two-stroke oil • Secure the machine during transport. • For best results and performance use HUSQVARNA • In order to prevent unintentional starting of the engine, two-stroke engine oil, which is specially formulated for the spark plug cap must always be removed during our air-cooled two-stroke engines.

  • Page 12: Fuelling

    FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

  • Page 13: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Inspect the working area. Remove any objects that WARNING! The complete clutch cover could be thrown out. and shaft must be fitted before the • Check the cutting attachment. Never use blades that machine is started, otherwise the clutch are dull, cracked or damaged.

  • Page 14: Warm Engine

    STARTING AND STOPPING Warm engine Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Starting Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.

  • Page 15: Working Techniques

    WORKING TECHNIQUES General working instructions • Never work from a ladder, stool or any other raised position that is not fully secured. IMPORTANT! This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.

  • Page 16: Basic Working Techniques

    WORKING TECHNIQUES • Check the working area for foreign objects such as • Hold the machine as close to your body as possible to electricity cables, insects and animals, etc, or other get the best balance. objects that could damage the cutting attachment, such as metal items.

  • Page 17: Transport Position

    WORKING TECHNIQUES Transport position (325HE4) Once the work has been completed fold the cutting unit back against the shaft to simplify transport and storage of the hedge trimmer. Turn off the engine. Fit the transport guard to the cutting attachment. Loosen the knob on the shaft (clockwise).

  • Page 18: Maintenance

    Basic setting • The basic carburettor settings are adjusted during Your Husqvarna product has been designed and testing at the factory. The basic setting is richer than manufactured to specifications that reduce harmful the optimal setting and should be maintained for the emissions.

  • Page 19: Muffler

    MAINTENANCE Muffler Cooling system CAUTION! Some mufflers are fitted with a catalytic To keep the working temperature as low as possible the converter. See chapter on Technical data to see whether machine is equipped with a cooling system. your machine is fitted with a catalytic converter. The muffler is designed to reduce the noise level and to direct the exhaust gases away from the operator.

  • Page 20: Air Filter

    Oiling the air filter operation or earlier if necessary. Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 21: Cleaning And Lubrication

    MAINTENANCE Cleaning and lubrication Clean any resin and plant residue from the blades using cleaning agent 531 00 75-13 (UL22) before and after using the machine. Lubricate the blade bars with special grease, part no. 531 00 75-12 (UL 21) before long periods of storage. –...

  • Page 22: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual.

  • Page 23: Technical Data

    TECHNICAL DATA Technical data Technical data 325HE3 325HE4 Engine Cylinder displacement, cm 24,5 24,5 Cylinder bore, mm 34,0 34,0 Stroke, mm Idle speed, rpm 2700 2700 Recommended max. speed, rpm 11000-12600 11000-12600 Max. engine output, acc. to ISO 8893 0,9/9000 0,9/9000 Catalytic converter muffler Speed-regulated ignition system...

  • Page 24: Ec-Declaration Of Conformity

    Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 325HE3 and 325HE4 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:...
  • Page 28 Original instructions 1153292-26 ´®z+U=6¶6B¨ ´®z+U=6¶6B¨ 2010-03-08...

This manual is also suitable for:

325he4 x-series

Table of Contents