Husqvarna 325HDA55X-series Operator's Manual
325hda55x-series 325he3x-series 325he4x-series operators manual
Hide thumbs
Also See for 325HDA55X-series:
- Operator's manual (24 pages) ,
- Operator's manual (24 pages) ,
- Operator's manual (22 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Husqvarna 325HDA55X-series
Summary of Contents for Husqvarna 325HDA55X-series
- Page 1 325HDA55 X-series Operator s manual 325HE3 X-series 325HE4 X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
Symbols WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you read and understand the contents of this operator’s manual. -
Page 3: Table Of Contents
Machine s safety equipment ... Checking, maintaining and servicing the machine s safety equipment ... General safety precautions ... Safety instructions when using the hedge trimmer ... WHAT IS WHAT? What is what? ... ASSEMBLY Fitting the hand guard and loop handle ... -
Page 4: Safety Instructions
SAFETY INSTRUCTIONS Personal protective equipment IMPORTANT! Whenever you use the hedge trimmer you must use personal protective equipment that is approved by the authorities. Personal protective equipment does not eliminate the risk of injury, but it can reduce the degree of injury in the event of an accident. - Page 5 SAFETY INSTRUCTIONS Vibration damping system Your machine is equipped with a vibration damping system that is designed to minimise vibration and make operation easier. The machine s vibration damping system reduces the transfer of vibration between the engine unit/cutting equipment and the machine s handle unit.
-
Page 6: Checking, Maintaining And Servicing The Machine S Safety Equipment
• See instructions under the heading Start. Start the hedge trimmer and apply full throttle. Release the throttle trigger and check that the blades stop and remain stationary. If the blades move when the throttle trigger is in the idle position then the carburettor idle setting must be adjusted. -
Page 7: Gear Housing
SAFETY INSTRUCTIONS Muffler • Never use a machine that has a faulty muffler. • Regularly check that the muffler is securely attached to the machine. • If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh will cause the engine to overheat and may lead to serious damage. -
Page 8: General Safety Precautions
SAFETY INSTRUCTIONS General safety precautions IMPORTANT! The machine is only designed for cutting branches and twigs. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. Wear personal protective equipment. -
Page 9: Safety Instructions When Using The Hedge Trimmer
SAFETY INSTRUCTIONS Safety instructions when using the hedge trimmer WARNING! The machine can cause serious personal injury. Read the safety instructions carefully. Learn how to use the machine. WARNING! Cutting tool. Do not touch the tool without first switching off the engine. -
Page 10: Basic Working Techniques
• Do not rush the work, but work steadily until all the branches have been cut back cleanly. 10 – English Changing the hedge trimmer angle (325HE3,325HE4) • Undo the knob. • Grasp the handle on the angle stop, adjust to the desired angle and then tighten the knob. -
Page 11: What Is What
What is what? 1 Cutter 2 Grease nipples (3) 3 Bevel gear 4 Cutter guard (325HDA55) 5 Shaft 6 Front handle (325HDA55,325HE3) 7 Front handle (325HE4) 8 Throttle control 9 Stop switch 10 Throttle lock 11 Harness support hook (325HE4) 12 Cylinder cover 13 Starter handle 14 Fuel tank... -
Page 12: Assembly
English ASSEMBLY Fitting the cutting head It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the cutting head may not be fitted straight. 1 Fit the cutting head to the shaft. CAUTION! Make sure the drive shaft inside the shaft engages with the recess in the cutting head. -
Page 13: Fuel Handling
Fuel CAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two- stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. -
Page 14: Starting And Stopping
STARTING AND STOPPING Check before starting • Inspect the working area. Remove any objects that could be thrown out. • Check the cutting attachment. Never use blades that are dull, cracked or damaged. • Check that the machine is in perfect working order. Check that all nuts and screws are tight. - Page 15 STARTING AND STOPPING Air purge: Press the air purge diaphragm repeatedly until fuel begins to fill the diaphragm. The diaphragm need not be completely filled. Hold the body of the machine on the ground using your left hand (CAUTION! Not with your foot!). Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip), now quickly and powerfully pull the cord.
-
Page 16: Maintenance
Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. After the engine has used 8-10 tanks of fuel the engine will be run-in. To ensure that it continues to run at peak performance and to minimise harmful exhaust emissions after the running-in period, ask your dealer/service workshop (who will have a rev counter at their disposal) to adjust your carburettor. -
Page 17: Muffler
The blades must also remain stationary when the choke control is in the start throttle position. IMPORTANT! If the idle speed cannot be adjusted so that the cutting attachment stops, contact your dealer/service workshop. Do not use the machine until it has been correctly adjusted or repaired. -
Page 18: Cooling System
Cooling system To keep the working temperature as low as possible the machine is equipped with a cooling system. The cooling system consists of: 1 Air intake on the starter. 2 Fins on the flywheel. 3 Cooling fins on the cylinder. 4 Cylinder cover (directs cold air over the cylinder). -
Page 19: Gear Housing
Gear housing There are three grease nipples on the gear housing. Use a grease gun to top up with grease. This should be carried out approximately every 20 working hours. Use Husqvarna special grease, part no. 503 98 96-01. CAUTION! The gear housing must not be filled completely with grease. -
Page 20: Technical Data Technical Data
Technical data Technical data Engine Cylinder displacement, cm Cylinder bore, mm Stroke, mm Idle speed, rpm Recommended max. speed, rpm Max. speed;should not be exceded, rpm Max. engine output, acc. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm... -
Page 21: Ec-Declaration Of Conformity (Applies To Europe Only)
TECHNICAL DATA EC-declaration of conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 325HDA55, 325HE3 and 325HE4 from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES: of June 22, 1998 ”relating to machinery”... - Page 22 1140176-26 ´®z+H1^¶6[¨ ´®z+H1^¶6[¨ 2003-07-07...
- Page 23 Garden tractors Garden vacuums Hover mowers Husqvarna chainsaws Lawn scarifiers Lawn tractors Petrol hedge Ride on lawn cutters mowers Ryobi strimmers Scarifiers Gardening Tools Direct Brushcutters Chainsaws Cylinder mowers Echo chainsaws Garden blowers Garden rollers Hayter lawn Hedge cutters mowers...