hit counter script
Download
Share
Print this page
HP 3C509B-TP Installation Manual
  1. Manuals
  2. Brands
  3. HP Manuals
  4. Network Card
  5. 3C509B-TP
  6. Installation manual

HP 3C509B-TP Installation Manual

Hewlett-packard network interface card owner's manual
Hide thumbs Also See for 3C509B-TP:

Advertisement

Quick Links

Download this manual
Etherlink IIIB ISA Network
Interface Card (10BT)
3C509B-TP
Installation Guide

Advertisement

loading

Related Manuals for HP 3C509B-TP

Summary of Contents for HP 3C509B-TP

  • Page 1 Etherlink IIIB ISA Network Interface Card (10BT) 3C509B-TP Installation Guide...
  • Page 2 Notice The information contained in this document is subject to change without notice. Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
  • Page 3 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Power on the machine and allow it to boot to a DOS prompt.
  • Page 4 Under the heading "Select the driver for your network board", insert the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\CLI- ENT." (If you have an HP preloaded HDD, set path to "C:\Masters\Lan- Drv\3C509\NWCLIENT\) c Press "Enter" to continue the installation.
  • Page 5 9 Select 16-bit LAN Drivers and hit the enter key. 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:\NWCLIENT\” and press enter. 12 Select “3Com Etherlink III Parallel Tasking Family”...
  • Page 6 1 Connecting to a Netware 3.12 Server Windows for Workgroups...
  • Page 7 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.
  • Page 8 1 Connecting to a Netware 3.12 Server Windows 95 SR2 5 If changes are required, save those changes and exit. 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.”...
  • Page 9 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Power on the machine and allow it to boot to a DOS prompt.
  • Page 10 Under the heading "Select the driver for your network board", insert the 3Com 3C590 drivers disk and set the path to "A:\NETWARE\ CLIENT." (If you have an HP preloaded HDD, set path to "C:\ Masters\LanDrv\3C509\NWCLIENT\) d Press "Enter" to continue the installation.
  • Page 11 10 Page down the Board Drivers list to “USER SPECIFIED 16 BIT DRIVER” and hit enter. 11 Insert the 3COM Etherlink 3C509 Ethernet card and drivers disk, set the path to “A:\NWCLIENT\” and press enter. 12 Select “3Com Etherlink III Parallel Tasking Family” and press enter. 13 Accept the default settings, press “F10”...
  • Page 12 2 Connecting to a Netware 4.11 Server Windows for Workgroups...
  • Page 13 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Power on the machine and restart Windows 95 SR2 in MS-DOS Mode.
  • Page 14 2 Connecting to a Netware 4.11 Server Windows 95 SR2 6 Remove the 3com cards driver diskette and restart the machine. 7 After windows loads, click on “Start,” to “Settings” and over to “Control Panel.” 8 Double click on “Network” and select “Add.” 9 Choose to add an adapter, click on “Add”...
  • Page 15 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network Cable Media to the 3COM 3C509B card. 3 After booting to DOS, insert the 3COM’s drivers disk “Etherlink 3C509-B Ethernet ver.
  • Page 16 12 Type the path “A:\WFW311” in the “Install Driver” dialog box, and then insert the 3COM 3C509 drivers disk into the floppy drive, and click “OK.” (If you have an HP preloaded HDD, set path to “C:Masters\LanDrv\3C509B\WFW311”) 13 Select “3Com Etherlink III (3C5X9)” in the “Unlisted or Updated Network Adapter”...
  • Page 17 3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11...
  • Page 18 3 Connecting to a Windows NT Server 3.51 Windows for Workgroups Ver. 3.11...
  • Page 19 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network cable media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 20 14 With the Path set to “A:\” in the “Install From Disk” dialog box click “OK”. (If you have an HP pre-loaded HDD, set the path statement to “C:\MASTERS\LANDRV\3C509B\”) 15 Select the “3Com Etherlink III ISA (3C509/3C509B) in ISA mode” and click “OK.”...
  • Page 21 3 Connecting to a Windows NT Server 3.51 Windows 95 SR2 an HP preloaded HDD, set the path to “C:\MASTERS\WIN95\SYSTEM\CABS\”) 21 To complete the installation, select “Yes” to restart your computer.
  • Page 22 3 Connecting to a Windows NT Server 3.51 Windows 95 SR2...
  • Page 23 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network cable media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 24 Set the path to "A:\" in the "Insert Disk" dialog box, and then insert the 3COM 3C509 drivers disk. Click "OK" at the "Install Driver" dialog box. (If you have an HP pre- loaded HDD, set path to "C:\Masters\LanDrv\3C509\) k Select "3Com Etherlink III (3C509) ISA Adapter" in the Select OEM Option dialog box, and click "OK".
  • Page 25 11 In “Windows NT Setup”, enter the path to your NT files and click on “Continue.” (If you have an HP preloaded HDD, set path to “C:\I386”) 12 Click on “Do Not Detect” from the “ Network Adapter Card Detection”...
  • Page 26 3 Connecting to a Windows NT Server 3.51 Windows NT Workstation Version 3.51 19 Choose to install all applicable TCP/IP options and select “Continue.” (If you do not have the required information, contact your network administrator) 20 At the “Network Settings” dialog box, click on “OK.” 21 Accept the default “NWLink IPX/SPX Protocol Configuration”...
  • Page 27 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 28 18 At the “Network Services:” prompt, accept default settings and click on “Next.” 19 Finish the network card installation by clicking on “Next.” 20 Designate the path to your NT files and select “Continue.” (If you have a Hewlett-Packard pre-loaded HDD, set the path to “C:\I386”) 21 Accept type as “ISA”...
  • Page 29 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.” (If you do not have the required information, contact your network administrator) 27 After “Network has been installed on this computer” click on “Finish. 28 To complete the installation, select “Yes”...
  • Page 30 3 Connecting to a Windows NT Server 3.51 Windows NT Workstation 4.0...
  • Page 31 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network Cable Media to the 3COM 3C509B card. 3 After booting to DOS, insert the 3COM’s drivers disk “Etherlink 3C509-B Ethernet ver.
  • Page 32 12 Type the path “A:\WFW311” in the “Install Driver” dialog box, and then insert the 3COM 3C509 drivers disk into the floppy drive, and click “OK.” (If you have an HP preloaded HDD, set path to “C:\Masters\LanDrv\3C509B\WFW311”) 13 Select “3Com Etherlink III (3C5X9)” in the “Unlisted or Updated Network Adapter”...
  • Page 33 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network cable media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 34 14 With the Path set to “A:\” in the “Install From Disk” dialog box click “OK”. (If you have an HP pre-loaded HDD, set the path statement to “C:\MASTERS\LANDRV\3C509B\”) 15 Select the “3Com Etherlink III ISA (3C509/3C509B) in ISA mode” and click “OK.”...
  • Page 35 4 Connecting to a Windows NT Server 4.0 Windows 95 SR2 “C:\MASTERS\WIN95\SYSTEM\CABS\”) 22 To complete the installation, select “Yes” to restart your computer.
  • Page 36 4 Connecting to a Windows NT Server 4.0 Windows 95 SR2...
  • Page 37 • Plug and Play Compatibility • Full Duple Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network cable media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 38 11 In “Windows NT Setup”, enter the path to your NT files and click on “Continue.” (If you have an HP preloaded HDD, set path to “C:\I386”) 12 Click on “Do Not Detect” from the “ Network Adapter Card Detection”...
  • Page 39 administrator) 23 At the “Domain/Workgroup Settings” Dialog Box, click on “OK” to accept the default “Workgroup” as your workgroup name. (If you do not have the required information, contact your network administrator) 24 To complete the installation, remove the floppy disk , and click on “Restart Computer”...
  • Page 40 4 Connecting to a Windows NT Server 4.0 Windows NT Workstation Version 3.51...
  • Page 41 • Plug and Play Compatibility • Full Duplex Procedure 1 With the HP Vectra turned off, install the 3COM Etherlink III 3C509-B adapter card into an ISA slot. 2 Connect network media to the 3COM 3C509B card. 3 Insert a DOS bootable diskette and power on the machine.
  • Page 42 18 At the “Network Services:” prompt, accept default settings and click on “Next.” 19 Finish the network card installation by clicking on “Next.” 20 Designate the path to your NT files and select “Continue.” (If you have a Hewlett-Packard pre-loaded HDD, set the path to “C:\I386”) 21 Accept type as “ISA”...
  • Page 43 25 When “Windows NT is now ready to start the network…” click on “Next.” 26 Specify your Computer Name, Workgroup or Domain and click on “Next.” (If you do not have the required information, contact your network administrator) 27 After “Network has been installed on this computer” click on “Finish. 28 To complete the installation, select “Yes”...
  • Page 44 4 Connecting to a Windows NT Server 4.0 Windows NT Workstation 4.0...
  • Page 46 Version Number 3Com 3c509 Rev.1...

This manual is also suitable for:

Vectra ve6 8Vectra vec 7Vectra vl6 7Vectra vl6 8