Page 1 User’s Manual PORTÉGÉ M780...
Page 2: Table Of Contents
Table of Contents Copyright..........vi Disclaimer .
Page 3 Drive Kit II ..........4-37 TOSHIBA DVD PLAYER ........4-43 Media care .
Page 4 TOSHIBA support ........
Page 5 PORTÉGÉ M780 Hard Disk Drive (HDD) Capacity ......H-3 LCD ........... . H-3 Graphics Processor Unit ("GPU") .
Page 6: Copyright
Intel Corporation. Windows, Microsoft and Windows logo are registered trademarks of Microsoft Corporation. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. Photo CD is a trademark of Eastman Kodak Company. Memory Stick, Memory Stick PRO, Memory Stick PRO Duo and i.LINK are trademarks or registered trademarks of Sony Corporation.
Page 7: Fcc Information
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external monitor port, Universal Serial Bus...
Page 8: Eu Conformity Statement
Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment. This Class B digital apparatus meets all requirements of the Canadian Interference-Causng Equipment Regulations.
Page 9: Modem Warning Notice
PORTÉGÉ M780 Modem warning notice This information is applicable to the models equipped with a built-in modem. Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network...
Page 10 PORTÉGÉ M780 Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Page 11: Type Of Service
FCC. In the event repairs are ever needed on your modem, they should be performed by TOSHIBA Corporation or an authorized representative of TOSHIBA Corporation.
Page 12: Instructions For Ic Cs-03 Certified Equipment
PORTÉGÉ M780 Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
Page 13: Notes For Users In Australia And New Zealand
PORTÉGÉ M780 Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Page 14 PORTÉGÉ M780 ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem. The associated equipment shall be set to operate within the following limits for compliance with Telecom Specifications: a/ There shall be no more than 10 call attempts to the same number within any 30 minute period for any single manual call initiation, and b/ The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the...
Page 15: General Conditions
PORTÉGÉ M780 ■ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired.
Page 16: Following Information Is Only For Eu-Member States
For more detailed information about the collection and recycling programmes available in your country, please visit our website (http://eu.computers.toshiba-europe.com) or contact your local city office or the shop where you purchased the product. Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.
Page 17: Disposing Of The Computer And The Computer's Batteries
PORTÉGÉ M780 Disposing of the computer and the computer's batteries ■ Discard this computer in accordance with applicable laws and regulations. For further information, contact your local government. ■ This computer contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them.
Page 18: Preface
Preface Congratulations on your purchase of the PORTÉGÉ M780 series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M780 computer.
Page 19 PORTÉGÉ M780 Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+).
Page 20 PORTÉGÉ M780 Terminology This term is defined in this document as follows: Start The word "Start" refers to the " " button in ® Windows HDD or Hard disk Some models are equipped with a "Solid State drive Drive (SSD)" instead of a hard disk drive. In this manual, the word "HDD"...
Page 21: General Precautions
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Page 22: Heat Injury
PORTÉGÉ M780 Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Page 23: Equipment Checklist
Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Page 24 TOSHIBA ConfigFree ■ TOSHIBA HDD Protection ■ TOSHIBA Disc Creator ■ TOSHIBA eco Utility ■ TOSHIBA Face Recognition (Is preinstalled in some models) ■ TOSHIBA PC Health Monitor ■ TOSHIBA USB Sleep and Charge Utility ■ TOSHIBA Tablet PC Extension ■...
Page 25 About the Tablet mode Change to "The TOSHIBA PORTÉGÉ M780" computer can be used in two ways, as an ordinary laptop PC and as a Tablet PC. You can use the computer as Tablet PC, operated with the supplied Tablet PC Pen, by turning the display panel through 180 degrees and closing it.
Page 26: Connecting The Ac Adaptor
■ Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
Page 27 Getting Started 1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model.
Page 28: Opening The Display
Getting Started Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.
Page 29: Turning On The Power
Getting Started Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes for more information. ■...
Page 30: Turning Off The Power
Getting Started Turning off the power The power can be turned off in one of three modes, either Shut Down (Boot) Mode, Hibernation Mode or Sleep Mode. Shut Down mode (Boot Mode) When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on.
Page 31 Getting Started ■ Before entering Sleep Mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep Mode (unless the computer is connected to an AC power source).
Page 32: Hibernation Mode
Getting Started ■ Press the power button. Please note that this feature must be enabled within the Power Options (to access it, click Start -> Control Panel -> System and Security -> Power Options). When you turn the power back on, you can continue where you left when you shut down the computer.
Page 33: Restarting The Computer
Getting Started Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Point to the arrow icon ( ) and then select Hibernate from the menu Automatic Hibernation Mode...
Page 34: System Recovery Options
Getting Started ■ Press the power button and hold it down for five seconds. Once the computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button. System Recovery Options There is a hidden partition allocated on the hard disk drive for the System Recovery Options.
Page 35: System Recovery
Getting Started System Recovery This section describes the creation of Recovery Media and their use. Creating Recovery Media This section describes how to create Recovery Media. ■ Be sure to connect the AC adaptor when you create Recovery Media. ■ Be sure to close all other software programs except the Recovery Media Creator.
Page 36 Getting Started ® 4. Double click the Recovery Media Creator icon on the Windows desktop, or select the application from Start Menu. 5. After Recovery Media Creator starts, select the type of media and the title you wish to copy. The screen will display the number of discs or the capacity of USB Flash Memory required.
Page 37 4. A menu will be displayed from which you should follow the on-screen instructions. When drivers/utilities are installed, you can setup the respective drivers/utilities from the following place. To open the setup files, Click Start -> All Programs -> TOSHIBA -> Applications and Drivers. User’s Manual 1-15...
Page 38: Chapter 2 The Grand Tour
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix H.
Page 39 The Grand Tour System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section. Wireless Slide this switch to the left to turn off Wireless communication LAN, Bluetooth and Wireless WAN functions.
Page 40: Left Side
The Grand Tour Left side The following figure shows the computer’s left side. 1. Cooling vents 4. eSATA/USB combo port 2. Security lock slot 5. ExpressCard slot 3. Universal Serial Bus (USB 2.0) ports Figure 2-2 The left side of the computer The computer is equipped with an ExpressCard slot.
Page 41: Right Side
The Grand Tour Please note that it is not possible to confirm the operation of all functions of all USB devices that are available. In view of this it may be noted that some functions associated with a specific device might not operate properly. This slot allows you to install a single Express- ExpressCard slot Card device.
Page 42: Back
The Grand Tour Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. Ultra Slim Bay An Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II or Ultra Slim Bay HDD Adaptor II can be installed in the Ultra Slim Bay, which...
Page 43 The Grand Tour 1. Universal Serial Bus (USB 2.0) port 4. LAN jack 2. External monitor port 5. Link indicator (green) 3. DC IN 15V jack 6. LAN active indicator (orange) Figure 2-4 The back of the computer Universal Serial Bus One Universal Serial Bus port, which complies to (USB 2.0) port the USB 2.0 standard, is provided on the back of...
Page 44: Underside
The Grand Tour LAN active indicator This indicator may glow orange when the (orange) computer is connected to a LAN and the LAN is functioning properly. Underside The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
Page 45 Hardware, Utilities and Options. ■ Only the TOSHIBA Express Port Replicator can be used with this computer. Do not attempt to use any other Port Replicator. ■ Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry.
Page 46: Front With The Display Open
The Grand Tour Ultra Slim Bay Refer to the Right side section in this chapter for details. Ultra Slim Bay latch Slide the latch to release or secure the Ultra Slim Bay latch. Be sure to lock the Ultra Slim Bay latch before you transport or carry the computer.
Page 47 7. ESC/Rotation button 18. LCD Sensor switch (Not shown) 8. Windows Security tablet button 19. Memory module slot (Not shown) 9. TOSHIBA Assist button 20. Wireless LAN antennas and Wireless WAN antennas (Not shown) 10. TOSHIBA Presentation button 21. Bluetooth antenna (Not shown) 11.
Page 48 You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. It also has reading business card function. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph. It...
Page 49 When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer and launch the program. TOSHIBA The TOSHIBA Presentation button has the same Presentation button functionality as the Connect display button in the Mobility Center. When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer.
Page 50: Indicators
The Grand Tour Microphone A built-in microphone allows you to import and record sounds for your application - please refer to the Sound System section in Chapter 4, Operating Basics for more information. LCD Sensor switch This switch senses when the display panel is either closed or opened and activates the Panel Power Off/On feature as appropriate.
Page 51 The Grand Tour DC IN The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash orange.
Page 52: Keyboard Indicators
The Grand Tour Wireless The Wireless communication indicator blinks communication orange when the Bluetooth, Wireless LAN and Wireless WAN functions are turned on. Only some models are equipped with Bluetooth, Wireless LAN and Wireless WAN functions. Wireless WAN The Wireless WAN indicator glows or blinks blue when the Wireless WAN function is on.
Page 53: Optical Disc Drives
The Grand Tour CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. Arrow Mode When the Arrow Mode indicator lights green, you can use the gray labeled keys on the keypad overlay as cursor keys. Please refer to the Keypad overlay section in Chapter 5, The Keyboard for more information.
Page 54: Writable Discs
Writable discs This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics.
Page 55: Ac Adaptor
The Grand Tour DVD+RW write 8 speed (maximum) DVD-RAM write 5 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 4 speed (maximum) CD-RW (High-Speed) write 10 speed (maximum) CD-RW (Ultra-Speed) write 16 speed (maximum) AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use...
Page 56 Always use the TOSHIBA AC adaptor that was included with your computer, or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury.
Page 57: Chapter 3 Hardware, Utilities And Options
Your computer is equipped with one processor and processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start -> All Programs -> TOSHIBA -> Utilities -> PC Diagnostic Tool.
Page 58 Hardware, Utilities and Options Memory Module slot 1GB, 2GB or 4GB memory modules can be installed in the computer's two memory slots for a maximum of 8GB system memory. This computer can be equipped with memory modules of a maximum size of 8GB. The actual amount of useable system memory will be less than the installed memory modules.
Page 59 Hardware, Utilities and Options Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. Slice Expansion This battery pack increases your computer's Battery operating time when main battery pack is also installed. Legal Footnote (Battery Life) For more information regarding Battery Life, please refer to the Legal Footnotes section in Appendix H.
Page 60: Optical Disc Drive
Hardware, Utilities and Options ■ In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated. ■ SSD is a large-capacity storage media which uses Solid-State Memory in place of a magnetic disk of the hard disk. Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors.
Page 61 You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Page 62 Hardware, Utilities and Options Communications Modem Some models are equipped with the integrated modem. The integrated modem provides capability for data and fax communications that support the V.90 (V.92) standards and includes a modem jack for connection to the telephone line. Please note that both the V.90 and V.92 standards are only supported in the USA, Canada, United Kingdom, France, Germany and...
Page 63: Special Features
It is preinstalled in some models. Special features The following features are either unique to TOSHIBA computers or are advanced features which make the computer more convenient to use. Access each function using the following procedures.
Page 64 This can be specified in the Power Options. TOSHIBA HDD This feature uses the acceleration sensor built in Protection the computer to detect vibration and shocks, and...
Page 65 The TOSHIBA HDD Protection function does not guarantee that the hard disk drive will not be damaged. ■ TOSHIBA HDD Protection cannot be used in models that are equipped with SSD. Optical Drive Auto This function automatically locks the optical disc...
Page 66: Toshiba Value Added Package
Refer to Appendix G, TOSHIBA PC Health Monitor. TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. TOSHIBA Power TOSHIBA Power Saver provides you with the Saver features of more various power supply managements.
Page 67: Toshiba Tablet Pc Extension
TOSHIBA Tablet PC Extension This section describes the pre-installed TOSHIBA Component features that come with the computer. To access these components, click Start -> All Programs -> TOSHIBA ->Tablet PC. TOSHIBA Rotation This utility controls the screen orientation setting for both Laptop mode and Tablet mode.
Page 68: Utilities And Applications
Fingerprint Sensor section in Chapter 4, Operating Basics. TOSHIBA Face TOSHIBA Face Recognition uses a face Recognition verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically.
Page 69 To access this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Assist. TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities that improve the ease and control of communication devices and network connections, help in the...
Page 70 Alert the Disk Drive operating status and execute the system backup. To access this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD SSD Alert. TOSHIBA Service This application allows your computer to Station automatically search for TOSHIBA software...
Page 71 Lock from the menu). ■ TOSHIBA Assist : This can be used to open TOSHIBA Assist if it is already installed in your computer. TOSHIBA Tablet If a Windows password has been set, you can Access Code Logon...
Page 72: Optional Devices
Hardware, Utilities and Options 1. Turn on the computer while pressing the F2 key. When the TOSHIBA Leading Innovation >>> screen appears, release the F2 key. 2. Set the TPM in the Security tab to Enabled. 3. Press the F10 key.
Page 73: Inserting An Expresscard
The computer is equipped with a single ExpressCard slot into which any ExpressCard device that meets industry standards, either manufactured by TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps.
Page 74: Bridge Media Slot
Hardware, Utilities and Options 4. Grasp the ExpressCard and remove it. 1. ExpressCard Figure 3-2 Removing the ExpressCard 5. Insert the Dummy card into the ExpressCard slot. When you do not use an ExpressCard, please be sure to insert a Dummy card.
Page 75: Memory Media
Hardware, Utilities and Options ■ This Bridge media slot supports the following memory media. ■ Secure Digital (SD) Card (SD memory card, SDHC memory card, miniSD Card, microSD Card) ■ Memory Stick (Memory Stick, Memory Stick PRO, Memory Stick PRO Duo) ■...
Page 76: Card Care
Hardware, Utilities and Options ■ The SD memory card logo is ( ■ The SDHC memory card logo is ( ■ The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 32GB. Card Type Capacities 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB, 2GB...
Page 77: Memory Card Care
Hardware, Utilities and Options Memory card care ■ Set the write-protect switch to the lock position, if you do not want to record data. ■ Memory cards have a limited lifespan, so it is important to backup important data. ■ Do not write to a card if the battery power is low.
Page 78: Removing A Memory Media
Hardware, Utilities and Options ■ Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove ■ When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Page 79: Additional Memory Module
When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions.
Page 80 Hardware, Utilities and Options Installing a memory module (Slot A) To install a memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power off - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required).
Page 81 Hardware, Utilities and Options 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
Page 82 Hardware, Utilities and Options 1. Screws 2. Memory module cover Figure 3-8 Removing the memory module cover 10. Align the notch of the memory module with that of the memory module slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place.
Page 83 Hardware, Utilities and Options ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. ■...
Page 84 Hardware, Utilities and Options 13. Replace the keyboard and secure it using the two screws. Be sure to use all two screws removed in step 7. Make sure no screw was dropped into the computer. Make sure no foreign matter can be found inside the computer.
Page 85 Hardware, Utilities and Options 3. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required). 4. Follow steps 4 through 9 in Installing a memory module (Slot A) appear the memory module.
Page 86 Hardware, Utilities and Options Installing a memory module (Slot B) To install a memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power off - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required).
Page 87 Hardware, Utilities and Options 1. Slot B Figure 3-14 Seating the memory module ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
Page 88 Hardware, Utilities and Options 1. Screw 2. Memory module cover Figure 3-15 Seating the memory module cover 9. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required. 10. Turn your computer over. 11.
Page 89: Removing The Hard Disk Drive Pack
Hardware, Utilities and Options 1. Latches Figure 3-16 Removing the memory module 9. Seat the memory module cover in place and secure it with one screw. Take care to ensure that the memory module cover is firmly closed. 10. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required.
Page 90 Hardware, Utilities and Options 4. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required). 5. Loosen two screws securing the hard disk drive cover in place. 6.
Page 91 Hardware, Utilities and Options a. Hold the plastic tab and lift it carefully so that the hard disk drive pack slopes. Do not pull the cable. b. Grasp the edges of the connector with one hand and the edges of the hard disk drive pack with the other hand.
Page 92 Hardware, Utilities and Options 1. Hard disk drive pack 3. Connector 2. Plastic tab Figure 3-18 Removing the hard disk drive pack User’s Manual 3-36...
Page 93: Installing The Hard Disk Drive Pack
Hardware, Utilities and Options Installing the hard disk drive pack To install the hard disk drive pack, follow the steps as detailed below: 1. Grasp the edges of the connector with one hand and the edges of the hard disk drive pack with the other hand. 2.
Page 94 Hardware, Utilities and Options Ultra Slim Bay HDD Adaptor II You can increase your computer’s data storage capacity by installing an additional hard disk drive in the Ultra Slim Bay. To install a hard disk drive in the Ultra Slim Bay HDD Adaptor II follow the steps below.
Page 95: External Monitor
Hardware, Utilities and Options 3. Close the lid and slide the lock to the lock position. 1. Lid Figure 3-22 Closing the lid For details on inserting the Ultra Slim Bay HDD Adaptor II in the computer’s Ultra Slim Bay slot, refer to Chapter 4, Operating Basics.
Page 96: Usb Fdd Kit
Hardware, Utilities and Options 4. Turn the computer's power on. When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device. In the event that you find that there are issues getting an image displayed on the correct monitor, you should consider using the FN + F5 hot key to change the display settings (if you then disconnect the external monitor before you turn the computer's power off, be sure to press FN + F5 hot key again to...
Page 97 Hardware, Utilities and Options 1. USB connector 2. USB port Figure 3-25 Connecting the USB floppy diskette drive If you connect the USB floppy diskette drive after the computer has already been turned on, it will take about ten seconds for it to be recognized by the computer.
Page 98 Hardware, Utilities and Options eSATA (External Serial ATA) An device corresponding to eSATA function can be connected to the eSATA/USB combo port on the computer. Connecting the eSATA device To connect an eSATA device, follow the steps as detailed below: 1.
Page 99: Disconnecting An Esata Device
There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. ■ Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise.
Page 100 Hardware, Utilities and Options ■ Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer. Connecting the i.LINK (IEEE1394) cable To connect the i.LINK (IEEE1394) cable, follow the steps as detailed below: 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer.
Page 101: Toshiba Express Port Replicator
Hardware, Utilities and Options TOSHIBA Express Port Replicator In addition to the ports available on the computer, the TOSHIBA Express Port Replicator also provides several kinds of ports. The TOSHIBA Express Port Replicator connects directly to the docking interface on the underside of the computer.
Page 102: Optional Accessories
For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: DDR3-1066 Memory A 1 GB, 2GB or 4 GB memory module (DDR3- 1066) can easily be installed in the computer.
Page 103: Slice Expansion Battery Adaptor
4, LAN jack. Tablet PC Pen Tablet PC Pens can be purchased from your TOSHIBA dealer for use as spare items (spare pen tips and a tip draw-out tool are included). Reserve Pen Reserve Pen can be purchased from your TOSHIBA dealer.
Page 104: Chapter 4 Operating Basics
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. Pointing Devices The pointing devices of this computer vary from model to model. ■ Digitizer screen model: The Touch Pad and the Tablet PC Pen which comes with the computer can be used as a pointing device.
Page 105: Using The Touch Pad
Operating Basics Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. 1. Touch Pad control buttons 2. Touch Pad Figure 4-1 Touch Pad and Touch Pad control buttons The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right...
Page 106 Operating Basics Using the Tablet PC Pen and Reserve Pen You can use the Tablet PC Pen to execute actions and enter data. Hold the Tablet PC Pen in a natural position and tap, press or trace on the screen lightly.
Page 107 Pen and Input Device. ■ TOSHIBA is not liable for any problems arising on the products due to the use of the Tablet PC Pen in an environment where the above conditions are not satisfied or because of its use by unspecified number of users.
Page 108: Removing The Tablet Pc Pen
Operating Basics Removing the Tablet PC Pen To remove the Tablet PC Pen, follow the steps as described below: 1. Push the Tablet PC Pen in the Tablet PC Pen slot, so that it protrudes slightly. 2. Pull the Tablet PC Pen to remove it from the Tablet PC Pen slot. 1.
Page 109: Single Tap
When the pen tip breaks replace it with one of the refills delivered with the Tablet PC Pen. When these refills have run out, you can purchase a new pen set from a TOSHIBA authorized dealer. User’s Manual...
Page 110: Removing The Reserve Pen Case
■ It is recommended that you keep another pen set as a spare. You can buy replacement pen sets from your TOSHIBA authorized dealer. Removing the Reserve Pen case To remove the Reserve Pen case, follow the steps as detailed below: 1.
Page 111: Inserting The Reserve Pen Case
Operating Basics Inserting the Reserve Pen case To insert the Reserve Pen case, follow the steps as detailed below: 1. Insert the Reserve Pen case into the Reserve Pen case slot on the computer and slide it until it locks. 1.
Page 112: Using The Tablet Mode
Operating Basics Storing the Reserve Pen in the Reserve Pen case 1. Insert the tip of the Reserve Pen into the Reserve Pen case holder and press down. 1. Reserve Pen case 3. Reserve Pen 2. Reserve Pen case holder Figure 4-9 Storing the Reserve Pen in the Reserve Pen case Using the Tablet mode This section explains Tablet mode functions and use.
Page 113 Operating Basics ■ Do not use the computer while walking or driving a car. ■ Change to Laptop mode and turn off the computer before carrying it. Do not carry the computer with power on or in Sleep Mode. Do not carry the computer while the Hard Disk Drive indicator is glowing.
Page 114 Operating Basics ■ The display panel works as a touch sensitive digitizer screen. However, the outer edges of the screen may be less sensitive. Please keep the Tablet PC Pen or your finger inside the display area when you use it near the edges of the display panel.
Page 115: Changing To The Tablet Mode
Operating Basics Changing to the Tablet mode To change from Laptop mode to the Tablet mode, follow the instructions below. 1. Open the display panel to the upright position. When rotating the display panel, be sure to keep the display panel at a 90-degree angle to the keyboard.
Page 116 Operating Basics 2. Rotate the display panel clockwise slowly. ■ When rotating display panel of your computer, be sure to slowly turn it in the proper direction, and not apply excessive force or speed. ■ Do not attempt to rotate the display panel past the maximum rotation point.
Page 117: Changing The Screen Orientation
Operating Basics Changing to the Laptop mode To change the operating mode to the Laptop mode, follow the steps as detailed below: 1. Raise the display to the upright position carefully. 2. Rotate the display counter-clockwise slowly. 3. Close the display. Changing the screen orientation The orientation of the computer screen can be changed to one of the following four display modes:...
Page 118 Method 1: Changing the screen orientation using TOSHIBA Accelerometer Utilities and TOSHIBA Rotation Utility When the TOSHIBA Accelerometer Utilities and TOSHIBA Rotation Utility are running, changes in the orientation of the top and bottom of the screen is automatically recognized by pressing ESC/Rotation button for more than a second.
Page 119: Using Accelerometer Utilities
You can set the orientation of the desktop screen just after rotating the display from Start -> All Programs -> TOSHIBA -> Tablet PC -> Rotation Utility. Using Accelerometer Utilities When you shake the computer: ■...
Page 120: Using The Fingerprint Sensor
Operating Basics Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints. By enrolling the ID and password onto the fingerprint authentication feature, it is no longer necessary to input the password from the keyboard.
Page 121 Operating Basics ■ Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail.
Page 122: Fingerprint Utility Limitations
TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.
Page 123 1. Click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Fingerprint Utility, or click the utility icon in the Task Bar. 2. The Enroll screen is displayed. Enter the current account password into the Windows Password field.
Page 124 6. "Are you sure you want to quit" is displayed. Click OK. It will be returned to the TOSHIBA Fingerprint Utility main menu. Delete all users fingerprints 1. In the TOSHIBA Fingerprint Utility main menu, click Run as administrator in lower left. 2. User Account Control window is displayed. Click Yes.
Page 125 ■ It is necessary to register the User Password before using the fingerprint boot authentication feature and its extended function, the fingerprint Single sign-on feature. Please use TOSHIBA HW Setup to register the User Password. ■ If you fail fingerprint authentication more than five times, you must enter the User Password or Supervisor Password manually to start the computer.
Page 126: Toshiba Button Support
How to enable fingerprint boot authentication and Single sign-on feature It is necessary to first enroll your fingerprint with the TOSHIBA Fingerprint Utility prior to enabling and configuring the boot authentication and Single sign-on feature. You should check that your fingerprint is enrolled before configuring the settings.
Page 127: Web Camera
You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
Page 128 Operating Basics 1. Microphone 3. Web Camera LED 2. Web Camera Figure 4-18 Web Camera Please refer to the Web Camera Application Online Help for details. ■ Do not point the web camera directly at the sun. ■ Do not touch or press strongly on the web camera lens. Doing so may reduce image quality.
Page 129: Using The Toshiba Face Recognition
Toshiba does not guarantee that the face recognition utility will accurately screen out unauthorized users at all times. Toshiba is not liable for any failure or damage that might arise out of the use of the face recognition software or utility.
Page 130 Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition. ■...
Page 131: Auto Mode Login Screen
Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> Face Recognition. The Management screen is displayed.
Page 132: Changing Ultra Slim Bay Modules
Operating Basics 1:1 Mode Login screen 1. Turn on the computer. 2. The Select Tiles screen will be displayed. 3. Select Start face recognition ( 4. The Select Account screen will be displayed. 5. Select the account, and click the arrow button. 6.
Page 133 Operating Basics Wait for all disk indicators to go out before you turn over the computer and do not lay the computer down gently. Shock can damage the HDD or other components. 5. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required).
Page 134 Operating Basics 3. If you want to lock the Ultra Slim Bay HDD Adaptor II, set the Ultra Slim Bay lock screw in the hole for the lock position. 1. Unlock position 3. Lock screw (Lock position) 2. Ultra Slim Bay HDD Adaptor II Figure 4-20 Inserting the Ultra Slim Bay HDD Adaptor II Ultra Slim Bay Case The Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II is equipped...
Page 135 Operating Basics 1. Ultra Slim Bay DVD Super Multi (Double Layer) 2. Ultra Slim Bay latch Drive Kit II unit Figure 4-21 Removing the Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II unit Inserting a unit To insert the Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II unit into the Ultra Slim Bay Case, follow the steps as described below: ■...
Page 136: Using Optical Disc Drives
Operating Basics Using optical disc drives The full-size drive provides high-performance execution of CD/DVD-ROM- based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD- ROM, an indicator on the drive glows.
Page 137 Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. 1. Laser lens Figure 4-24 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray.
Page 138: Removing Discs
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Page 139 Operating Basics 3. Push the center of the disc tray to close it. Press gently until it locks into place. Optical Drive Auto Lock This function automatically locks the optical disc drive eject button if the computer detects any vibration or other shocks while running on the battery.
Page 140 You can use the Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II to write data to either CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD- RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM discs. TOSHIBA Disc Creator is provided as writing software with this computer. ■ Please refer to the...
Page 141: Important Message
RAM media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., Ltd., MITSUBISHI KAGAKU MEDIA Co.,Ltd.
Page 142 Operating Basics DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 MITSUBISHI KAGAKU MEDIA Co.,Ltd. (for 8x and 16x speed media) TAIYO YUDEN Co.,Ltd.(for 8x and 16x speed media) Hitachi Maxell,Ltd. (for 8x and 16x speed media) DVD-R (Dual Layer): MITSUBISHI KAGAKU MEDIA Co.,Ltd.
Page 143 Operating Basics ■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD- RAM media will be affected by the quality of the disc itself and the way in which it is used. ■ There are two types of DVD-R media available, authoring discs and general use discs.
Page 144: Drive Kit Ii
■ Keep mobile phones and other wireless communication devices away from the computer. TOSHIBA Disc Creator Please be aware of the following limitations when you use the TOSHIBA Disc Creator: ■ DVD Video cannot be created using TOSHIBA Disc Creator.
Page 145 CD Player' function to record music to DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW media. ■ Do not use the 'Disc Backup' function of TOSHIBA Disc Creator in order to copy DVD Video or DVD-ROM material that has copyright protection. ■...
Page 146: Toshiba Dvd Player
1. Click Start -> All Programs -> TOSHIBA -> CD&DVD Application -> Disc Creator to access the TOSHIBA Disc Creator utility. 2. Open the Data CD/DVD Setting dialog box by one of the following methods: ■...
Page 147 When playing DVD-Video using battery power, set the Power Options to "Balance". ■ Screen savers will not display while playing a movie in the "TOSHIBA DVD PLAYER". The computer will also not go into Sleep Mode, Hibernation Mode or shutdown while using "TOSHIBA DVD PLAYER".
Page 148 TOSHIBA DVD PLAYER. Figure 4-28 Application selection screen 2. Touch the CD/DVD panel on the Front operation panel. Or select Start -> All Programs -> TOSHIBA DVD PLAYER -> TOSHIBA DVD PLAYER to start "TOSHIBA DVD PLAYER". Operating TOSHIBA DVD PLAYER Notes on Using "TOSHIBA DVD PLAYER".
Page 149: Media Care
Operating Basics Open TOSHIBA DVD PLAYER HELP TOSHIBA DVD PLAYER features and instructions are also explained in detail in "TOSHIBA DVD PLAYER Help". Use the following procedure to open "TOSHIBA DVD PLAYER Help". ■ Click the "Help" button ( ) in the Display Area.
Page 150: Sound System
Operating Basics 5. Never use a pencil for writing on a floppy diskette label as the dust from the pencil lead could cause a system malfunction if it found its way onto the computer's components. In this instance, always use a felt-tipped pen and write the label first before applying it to the floppy diskette.
Page 151: Power Management
Operating Basics Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. Right click on the speaker icon on the Taskbar, and select Playback devices from the sub menu. 2. Select Speakers, and click Properties. 3.
Page 152: Modem
5. On the Advanced tab, select “2 channel, 16 bit, 48000 Hz (DVD Quality)” in the pull-down menu of the Default Format pane. 6. On the TOSHIBA Mic Effect tab, select the Enable Echo Canceller check box, and click Apply.
Page 153: Properties Menu
Check the specified areas carefully before using it. To select a region, follow the steps as detailed below: 1. Click Start -> All Programs -> TOSHIBA -> Networking -> Modem Region Select. If it is available, do not use the Country/Region Select function included as...
Page 154: Modem Selection
Operating Basics Location list for region selection. Displays a sub-menu appears which details location information. Open dialog box, if the modem and Telephony Current Location region code do not match. Displays a warning if the current settings for both region code and telephony location are different.
Page 155: Wireless Communications
Operating Basics 1. Modem jack 2. Telephone jack Figure 4-29 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical drive or hard disk drive connected to a 16-bit PC Card, you might experience the following problems with the operation of the modem: ■...
Page 156: Wireless Lan
Operating Basics ■ Do not use the Wireless LAN (Wi-Fi), Bluetooth or Wireless WAN functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi, Bluetooth or Wireless WAN operation. ■...
Page 157: Worldwide Operation
■ TOSHIBA is not liable for the loss of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof. Bluetooth wireless technology ™...
Page 158: Bluetooth Stack For Windows By Toshiba
This Bluetooth Stack is based on the Bluetooth Version 1.1/1.2/2.0+EDR/2.1+EDR specification. However, TOSHIBA cannot confirm the compatibility between any computing products and/or other electronic devices that use Bluetooth, other than TOSHIBA notebook computers. Release Notes related to the Bluetooth Stack for Windows by TOSHIBA 1.
Page 159: Lan
Operating Basics Wireless communication Indicator The wireless communication indicator shows the status of the computer's wireless communication functions. Indicator status Indication Indicator off The wireless communication switch is off - no wireless functionality is available. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Page 160: Connecting The Lan Cable
Operating Basics Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up.
Page 161: Computer Handling
Operating Basics Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector.
Page 162: Using The Hard Disk Drive (Hdd) Protection
This function does not guarantee that the hard disk drive will not be damaged. ■ The secondary hard disk drive is not supported by the TOSHIBA HDD protection function. ■ TOSHIBA HDD Protection cannot be used in models that are equipped with SSD.
Page 163: Taskbar Icon
TOSHIBA HDD Protection is disabled. TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD Protection Settings.
Page 164: Using The Toshiba Usb Sleep And Charge Utility
Intensely shaking the computer or other subjecting it to strong impacts may cause damage to the computer. Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
Page 165: Starting The Usb Sleep And Charge Utility
USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. Starting the USB Sleep and Charge Utility To start the utility, click Start-> All Programs -> TOSHIBA -> Utilities -> USB Sleep and Charge. User’s Manual...
Page 166: Heat Dispersal
Operating Basics Enabling USB Sleep and Charge This utility can be used to enable and disable the USB Sleep and Charge function in groups. USB Sleep and Charge compatible USB ports are assigned to each group. Select the check boxes for each group to enable the USB Sleep and Charge function for the USB ports assigned to that group.
Page 167: Chapter 5 The Keyboard
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
Page 168: Function Keys: F1
Soft keys: FN key combinations The FN (function) is unique to TOSHIBA computers and is used in combination with other keys to form soft keys. Soft keys are key combinations that enable, disable or configure specific features.
Page 169: Hot Keys
The Keyboard Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more...
Page 170 The Keyboard Sleep: Pressing FN + F3 switches the system to Sleep Mode. Hibernate: Pressing FN + F4 switches the system to Hibernation Mode. Output: Pressing FN + F5 changes the active display device. Brightness Down: Pressing FN + F6 decreases the computer's display panel brightness in individual steps.
Page 171: Windows Special Keys
FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F Number" key. To start the TOSHIBA Accessibility utility, click Start -> All Programs - >...
Page 172: Keypad Overlay
The Keyboard Keypad overlay Your computer's keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at their front edge.
Page 173: Generating Ascii Characters
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold down FN key and press any other key - this key will operate as if the overlay were off.
Page 174: Chapter 6 Power And Power-Up Modes
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use of these resources, and includes information on charging and changing batteries, tips for saving battery power, and information on the different power-up modes.
Page 175 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) 2nd battery fully • Operates • No charge adaptor charged • No charge • LED: 2nd battery green connected • LED: 2nd battery green DC IN green DC IN green 2nd battery •...
Page 176 Power and Power-Up Modes Table 6-1 Power conditions continued Power on Power off (no operation) 2nd battery • Operates adaptor charge is above • LED: 2nd battery off low battery DC IN off connected trigger point 2nd battery • Operates charge is below •...
Page 177: Monitoring Of Power Condition
Power and Power-Up Modes Monitoring of power condition As shown in the below table, the Battery, 2nd battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the main battery and the 2nd battery indicator to determine the status of the Slice Expansion Battery.
Page 178: Battery
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status of the computer - the following indicator conditions should be noted: Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor...
Page 179 Check system. Then press [F2] key. You can change the Real Time Clock settings by turning the computer on while pressing the F2 key and then release the F2 key when the TOSHIBA Leading Innovation >>> screen appears. Please refer to Chapter 8 Troubleshooting for further information.
Page 180: Charging The Batteries
- the Battery indicator will glow orange while the battery is being charged. Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger. Time The following table shows the approximate time required to fully charge a discharged battery.
Page 181: Battery Charging Notice
Power and Power-Up Modes Battery charging notice The battery may not begin charging immediately under the following conditions: ■ The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5°C to 35°C (41°F to 95°F).
Page 182: Maximizing Battery Operating Time
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on: ■ Processor speed ■ Screen brightness ■...
Page 183: Extending Battery Life
Power and Power-Up Modes Extending battery life To maximize the life of your battery packs: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below.
Page 184: Removing The Battery Pack
Power and Power-Up Modes Removing the battery pack To remove a discharged battery, follow the steps as detailed below: 1. Save your work. 2. Turn the computer's power off - ensure that the Power indicator is off. 3. Remove all cables and peripherals that are connected to the computer. 4.
Page 185: Installing The Battery Pack
Power and Power-Up Modes 1. Battery pack 2. Battery release latch Figure 6-2 Releasing the battery pack (2) Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries.
Page 186 Power and Power-Up Modes When handling Slice Expansion Battery, be careful not to short circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing and do not twist or bend the latches of it. 1.
Page 187: Disconnecting The Slice Expansion Battery
Power and Power-Up Modes 1. Latches Figure 6-5 Securing the latches Disconnecting the Slice Expansion Battery To disconnect the Slice Expansion Battery from the computer, follow the steps as detailed below: 1. Save your work. 2. Turn the computer’s power off. Make sure the Power indicator is off. 3.
Page 188: Toshiba Password Utility
7. Be sure to replace the protective cap before storing the Slice Expansion Battery. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password.
Page 189 ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held...
Page 190: Tablet Mode
If you set a Supervisor Password, some functions might be restricted when a user logs on with the User Password. To set a Supervisor Password, execute the file TOSPU.EXE. The file is located at: C:\Program Files\Toshiba\PasswordUtility\TOSPU.exe This utility lets you do the following: ■...
Page 191: Power-Up Modes
PC Pen or your finger. An * (asterisk) is displayed after "Password =" and one character is input for every tapping. Register your password to the computer in the Laptop mode using the standard keyboard. Refer to TOSHIBA Password Utility, in this chapter for the detail. Power-up modes The computer has three different power-up modes as follows: ■...
Page 192: Panel Power On/Off
Power and Power-Up Modes Panel power on/off You can set up your computer so that power is turned off automatically when you close the display panel, and turned on again when you open it. Please note that this function is only available for Sleep Mode or Hibernation Mode, not for Boot Mode.
Page 193: Chapter 7 Hw Setup
Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains a number of tabs (General, Display, Boot Priority, Keyboard, CPU, LAN, SATA and USB) to allow specific functions of the computer to be configured.
Page 194: Boot Priority
HW Setup General This window displays the BIOS version and contains two buttons : Default and About. Return all HW Setup values to the factory Default settings. Display the HW Setup version. About Setup This field displays the installed BIOS Version and date, and the EC Version.
Page 195 To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. when the TOSHIBA Leading Innovation >>> screen appears, release the F12 key. 2. Use the up and down cursor keys to select the boot device you want and press ENTER.
Page 196 HW Setup Sets the USB memory to be the equivalent of a floppy diskette drive. With this setting, the USB memory device can be used to start the computer as though it were a floppy diskette based on the floppy diskette drive settings within the Boot Priority option detailed previously.
Page 197 HW Setup Do not install or remove a memory module while Wake-up on LAN is enabled. ■ The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. ■ Regarding Wake-up on LAN from sleep or hibernation, you must check the "Allow the device to wake the computer"...
Page 198 HW Setup Enables the USB floppy diskette drive legacy Enabled emulation function (Default). Disables the USB floppy diskette drive legacy Disabled emulation function. SATA eSATA This feature allows you to set conditions for SATA. Enables the eSATA port. (Default) Enabled Disables the eSATA port in order to save power.
Page 199: Troubleshooting
Chapter 8 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Page 200: Analyzing The Problem
Troubleshooting ■ Before you attach an external device you should first turn the computer off, then when you turn the computer back on again it will recognize the new device. ■ Make sure all optional accessories are configured properly in the computer's setup program and that all required driver software has been loaded (please refer to the documentation included with the optional accessories for further information on its installation and...
Page 201: Hardware And System Checklist
Before using a peripheral device or application software that is not an authorized Toshiba part or product, make sure the device or software can be used with your computer. Use of incompatible devices may cause injury or may damage your computer.
Page 202: Self Test
This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system according to how the Boot Priority option is set within the TOSHIBA HW Setup program. If any of the following conditions are present, the self test has failed: ■...
Page 203: Ac Power
Troubleshooting It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking. If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact your reseller, dealer or service provider.
Page 204 Troubleshooting Problem Procedure Battery doesn’t charge If the battery is completely discharged, it will not when the AC adaptor is begin charging immediately, in these instances attached (Battery you should wait a few minutes before trying again. indicator does not glow If the battery still does not charge, you should orange).
Page 205: Real Time Clock
RTC Power 1. Turn on the computer while pressing the F2 Failure. key, and then release the F2 key when the Check system. TOSHIBA Leading Innovation >>> screen Then press [F2] appears - the BIOS setup application will key. load.
Page 206: Internal Display Panel
Alternatively problems occur you may wish to run the TOSHIBA PC Diagnostic Tool to check the general operation of the computer. If you are still unable to resolve the problem, contact your reseller, dealer or service provider.
Page 207: Hard Disk Drive
ROM in the optical disc drive - if so remove it and try to start the computer again. If this has no effect, check the Boot Priority setting within the TOSHIBA HW Setup utility - please refer to the Boot Priority...
Page 208 Troubleshooting Problem Procedure Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive. Please refer to the operating system's documentation or online Help File for further information on operating and using the Defragmentation utility.
Page 209: Usb Floppy Diskette Drive
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAM Check the region code on the DVD.
Page 210: Memory Stick
Troubleshooting Problem Procedure ExpressCard error Remove the ExpressCard from the computer and occurs then reinsert it in order to ensure it is firmly connected. In the event that the ExpressCard is attached to an external peripheral device, ensure that this connection is properly made.
Page 211: Xd Picture Card
Troubleshooting Problem Procedure Memory Stick/Memory Remove the Memory Stick/Memory Stick Stick PRO/Memory PRO/Memory Stick PRO Duo from the computer Stick PRO Duo error and then reinsert it in order to ensure it is firmly occurs connected. If the problem persists, then you should refer to the documentation supplied with your Memory Stick/Memory Stick PRO/Memory Stick PRO Duo for further information.
Page 212: Pointing Device
Troubleshooting Problem Procedure MultiMediaCard error Remove the MultiMediaCard from the computer occurs and then reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your MultiMediaCard for further information. You cannot write to a Remove the MultiMediaCard from the computer MultiMediaCard...
Page 213: Usb Mouse
Troubleshooting Problem Procedure The mouse pointer In this instance, you should initially try changing moves too fast or too the speed setting within the Mouse Control utility. slow 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse. 2.
Page 214: Fingerprint Sensor
Troubleshooting Problem Procedure Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse. 2.
Page 215: Usb Device
USB, you are still able to use a USB mouse and/or USB keyboard by setting the USB KB/Mouse Legacy Emulation option within the TOSHIBA HW Setup utility to Enabled. If you are still unable to resolve the problem, contact your reseller, dealer or service provider.
Page 216: Usb Sleep And Charge Function
Sleep and Charge disabled. function. Select the "Enable USB Sleep and Charge" check box in the TOSHIBA Sleep and Charge utility to enable this function. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.
Page 217: Esata Device
Troubleshooting Problem Procedure External devices Some external devices may not work when connected to the connected to a compatible port if the USB Sleep compatible ports do not and Charge function is enabled. work when connected Reconnect the external device after turning the to a compatible port.
Page 218 Troubleshooting Additional memory module Please also refer to Chapter 3, Hardware, Utilities and Options, for further information on installing and removing memory modules. Problem Procedure If there is a memory In the event the Power indicator flashes when malfunction, the Power the computer is turned on, you should first check indicator will repeatedly that the installed memory module(s) are...
Page 219: Volume Control Dial
Troubleshooting Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Please check to see if Mute is turned to Off Check to make sure the headphone connection is secure.
Page 220 Troubleshooting External monitor Please also refer to Chapter 3, Hardware, Utilities and Options, and to the documentation supplied with your monitor for further information. Problem Procedure Monitor does not turn After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet.
Page 221: I.link (Ieee1394) Device
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not Make sure the cable is securely connected to the function computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Click Start -> Control Panel ->...
Page 222 Troubleshooting Problem Procedure Character display When transmitting data you should ensure that becomes garbled the parity bit and stop bit settings correspond during a with those of the remote computer - you should communication check the flow control and communication protocol settings within your communication application.
Page 223: Recovery Media
Recovery Media section in Chapter1, Getting Started. You will be directed to select "Restore Original Factory Image" from the drop-down menu. If you have not created "Recovery Media", please contact TOSHIBA support for assistance. User’s Manual 8-25...
Page 224: Toshiba Support
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
Page 225 Troubleshooting Outside of Europe In Europe Singapore Spain TOSHIBA Singapore Pte. Ltd. TOSHIBA Information Systems, 438B Alexandra Road #06-01 ESPAÑA Alexandra Technopark Singapore Parque Empresarial San Fernando 119968 Edificio Europa, 1a Planta, Escalera A 28830, Madrid, España United States of America...
Page 226: Specifications
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions This section summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) * 1.99 kilograms, configured with: 30.7cm(12.1")WXGA, 1,024 MB RAM, 160GB HDD, Ultra Slim Bay DVD Super Multi (Double Layer) Drive Kit II, LAN (1000M bps), Wireless LAN, modem, Tablet PC Pen.
Page 227: Power Requirements
Specifications Wet-bulb 26°C maximum temperature Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 V DC 5.0 amperes Built-in Modem This information is applicable to the models equipped with a built-in modem.
Page 228 Specifications Communication Data transmission and reception speed 300/1200/2400/4800/7200/9600/12000/14400/16 800/19200/21600/24000/26400/28800/31200/33 600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps 2400/4800/7200/9600/12000/14400 bps Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output 600 ohms ±30% impedance Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis...
Page 229: Display Controller And Video Mode
Appendix B Display Controller and Video mode Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Due to the display panel's increased resolution, lines may appear broken in when displaying images in full-screen text mode.
Page 230: Wireless Lan
Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANs Compatibility ■...
Page 231: Radio Characteristics
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Page 232: Supported Frequency Sub-Bands
Subject to the radio regulations that apply in the countries/regions, your Wireless LAN module may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions.
Page 233 Wireless LAN ■ For Wireless LAN modules installed in wireless clients that operating in a peer-to-peer mode, the module will use the default channel 10. ■ In a Wireless LAN Access Point, the Wireless LAN module will use the factory-set default channel (printed in bold), unless the LAN Administrator selected a different channel when configuring the Wireless LAN Access Point device.
Page 234 Wireless LAN 5785* 5805* 5825* *1 The channel which can be used depends on the installed wireless LAN module. And the approved channels on using are different at each country or region. The channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN module will automatically start operation at the channel identified by the Wireless LAN Access Point.
Page 235: Appendix D Bluetooth Wireless Technology Interoperability
Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group. ■ When you use Bluetooth Adaptor from TOSHIBA close to 2.4 GHz Wireless LAN devices, Bluetooth transmissions might slow down or cause errors. If you detect certain interference while you use Bluetooth Adaptor from TOSHIBA, always change the frequency, move your computer to the area outside of the interference range of 2.4 GHz...
Page 236: Bluetooth Wireless Technology And Your Health
Because products with Bluetooth wireless technology operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Bluetooth wireless technology is safe for use by consumers. These standards and recommendations reflect the consensus of the scientific community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature.
Page 237 The radiated output power of the Bluetooth Adaptor from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Adaptor from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 238: Using Bluetooth Adaptor From Toshiba Equipment In Japan
3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. User’s Manual...
Page 239: Device Authorization
(3) 1: The interference range of this equipment is less than 10 m. This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday - Friday : 10:00-17:00 Toll Free Tel : 0120-15-1048...
Page 240: Ac Power Cord And Connectors
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters...
Page 241 AC Power Cord and Connectors Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: Germany: United Kingdom: In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2- 15P (250V) or 1-15P (125V) and three pin plug configuration must be 6- 15P (250V) or 5-15P (125V) as designated in the U.S.
Page 242: Toshiba Anti-Theft Protection Timer
BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility. The settings can only be activated or modified by a user with supervisor authority.
Page 243: Toshiba Pc Health Monitor
Once enabled, you may disable the TOSHIBA PC Health Monitor at any time by uninstalling the software via Uninstall a program in the Control Panel. Doing so will automatically delete all collected information from the HDD.
Page 244: Starting The Toshiba Pc Health Monitor
Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started using the following methods: ■ Click Start -> All Programs -> TOSHIBA -> Utilities -> PC Health Monitor. ■ Click the icon ( ) in the notification area, then click the "Enable PC Health Monitor..."...
Page 245: Cleaning The Cooling Module
TOSHIBA PC Health Monitor 4. If the "Please click [OK] to run the TOSHIBA Cooling Performance Diagnostic Tool to check the cooling performance of your PC." message is still displayed after running the "TOSHIBA Cooling Performance Diagnostic Tool" in step 3, it is recommended you turn off the computer and contact TOSHIBA support.
Page 246 TOSHIBA PC Health Monitor 3. Slide your fingernail or a thin object under the cover and lift it off. 1. Cooling module cover 2. Screw Figure G-1 Removing the cooling module cover 4. Lift the Fan hood up and out.
Page 247 TOSHIBA PC Health Monitor 9. Install the battery pack (refer to the Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required). 10. Turn your computer over. User’s Manual...
Page 248: Legal Footnotes
Appendix H Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis, unless you have selected all those features.
Page 249: Memory (Main System
86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your computer documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration.
Page 250: Battery Life
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Page 251: Wireless Lan
Legal Footnotes Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed.
Page 252: Glossary
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. Abbreviations AC: alternating current ANSI: American National Standards Institute ASCII: American Standard Code for Information Interchange BIOS: basic input output system bps: bits per second CD: compact disc CD-ROM: Compact Disc-Read Only Memory CD-RW: Compact Disc-ReWritable...
Page 253 Glossary IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte PC: personal computer PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock...
Page 254 Glossary ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games.
Page 255 Glossary byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Page 256 Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component.
Page 257 Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. dialog box: A window that accepts user input to make system settings or record other information.
Page 258 (FDD): An electromechanical device that reads and writes to floppy diskettes. Fn-esse: A TOSHIBA utility that lets you assign functions to hot keys. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk.
Page 259 FN, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. icon: A small graphic image displayed on the screen or in the indicator panel.
Page 260 Glossary I/O devices: Equipment used to communicate with the computer and transfer data to and from it. jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power.
Page 261 Glossary microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the Boot Mode, Sleep Mode or the Hibernation Mode.
Page 262 The electrical connection through which the computer sends and receives data to and from devices or other computers. Power Saver: A TOSHIBA utility that lets you set the parameters for various power-saving functions. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached.
Page 263 Glossary RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation.
Page 264 Glossary Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage. Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
Page 265: Index
3-13 using 4-17 problems 8-25 Floppy diskette care 4-46 Bridge media slot 2-4, 3-18 FN + 1 (TOSHIBA Zooming Utility reduce) indicator 2-14 using 3-18 FN + 2 (TOSHIBA Zooming Utility enlarge) FN + ENTER 5-3 Cleaning the computer 4-58...
Page 266 Power Plan 5-3 cable types 4-56 Sleep 5-4 connecting 4-57 TOSHIBA Zooming Utility (enlarge) disconnecting 4-58 jack 2-6 TOSHIBA Zooming Utility (reduce) 5-5 Link indicator 2-6 Touch Pad 5-4 problems 8-24 Wireless 5-4 Zoom 5-4 HW Setup Media care 4-46...
Page 267 Self test 8-4 problems 8-7 Sound system 8-21 Starting the computer by 6-17 System start-up 8-4 Supervisor 6-17 TOSHIBA support 8-26 user 6-15 Touch Pad 8-14 Pointing Device Wireless LAN 8-24 problems 8-14 Ultra Slim Bay DVD Super Multi drive...
Page 268 Stereo speakers 2-12 volume control dial 2-2 TOSHIBA Assist 3-13 TOSHIBA Assist button 3-7 TOSHIBA ConfigFree 3-13 TOSHIBA Disc Creator 3-14, 4-41 TOSHIBA DVD-RAM Utility 3-14 TOSHIBA Express Port Replicator 3-45, 3-47 TOSHIBA HDD Protection 3-8, 4-59 TOSHIBA PC Diagnostic Tool 3-10...

Toshiba Portege M780 User Manual

Chapter 1 Getting Started

Chapter 2 The Grand Tour

Chapter 3 Hardware, Utilities and Options

Chapter 4 Operating Basics

Chapter 5 The Keyboard

Chapter 6 Power and Power-Up Modes

Chapter 7 HW Setup

Chapter 8 Troubleshooting

Appendix A Specifications

Appendix B Display Controller and Video Mode

Appendix C Wireless LAN

Appendix D Bluetooth Wireless Technology Interoperability

Appendix E AC Power Cord and Connectors

Appendix F TOSHIBA Anti-Theft Protection Timer

Appendix G TOSHIBA PC Health Monitor

Appendix H Legal Footnotes

Quick Links

Related Manuals for Toshiba Portege M780

Summary of Contents for Toshiba Portege M780