Advertisement
Quick Links
INSTALLATION INSTRUCTIONS FOR
CEILING MOUNTING BRACKET FOR
USE ONLY WITH SHARP
PROJECTOR MODEL
XV-Z2000/DT-400
CEILING MOUNTING
BRACKET AN-CM270
AN-CM270
CEILING MOUNTING
BRACKET COMBINED
WITH OPTIONAL
ADJUSTABLE
EXTENSION TUBE
MODEL AN-EP101B
©
2004 SHARP ELECTRONICS CORPORATION
COPYRIGHT
Advertisement
Related Manuals for Sharp AN-CM270
Summary of Contents for Sharp AN-CM270
- Page 1 AN-CM270 INSTALLATION INSTRUCTIONS FOR CEILING MOUNTING BRACKET FOR USE ONLY WITH SHARP PROJECTOR MODEL XV-Z2000/DT-400 CEILING MOUNTING BRACKET AN-CM270 CEILING MOUNTING BRACKET COMBINED WITH OPTIONAL ADJUSTABLE EXTENSION TUBE MODEL AN-EP101B © 2004 SHARP ELECTRONICS CORPORATION COPYRIGHT...
- Page 2 THE WORK IS DONE IN COMPLIANCE WITH NEC AND ALL LOCAL BUILDING AND SAFETY CODES. SAVE THIS BOOKLET AFTER THE INSTALLATION IS COMPLETED. THE ACCESSORIES REFERRED TO IN THESE INSTRUCTIONS ARE INTENDED FOR USE ONLY WITH COMPATIBLE SHARP PROJECTORS. SEE SHARP PROJECTOR OWNER’S MANUAL OR SHARP DEALER TO DETERMINE SUITABILITY.
-
Page 3: Installation Instructions
LOCATION OF THE CEILING BRACKET Please refer to the owner’s manual for your SHARP LCD PROJECTOR for information which will help you to determine the best location for the placement of the ceiling mounting bracket assembly. - Page 4 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 Select straddle beam or single beam installation. Use the ceiling bracket as a template to mark the location where the pilot holes should be drilled. Drill the pilot holes for the support screws using a 1/8 ” drill bit into the center of the beam.
- Page 5 Select the contour appropriate for your application and cut out the opening along the line indicated on the label. Use a very sharp cutting tool. Thread the cable through the plastic trim cover. Place the plastic trim cover in place over the ceiling plate and press the velcro tabs together.
- Page 6 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 STEP 3 DETACH THE POSITIONING ASSEMBLY FROM THE PROJECTOR ATTACHMENT PLATE. NOTE: PLEASE LOOK OVER THE EXACT MANNER IN WHICH THE FIGURE 5 POSITIONING ASSEMBLY AND THE ATTACHMENT PLATE GO TOGETHER SO THAT YOU WILL BE ABLE TO REASSEMBLE THEM WHEN YOU HANG THE PROJECTOR.
- Page 7 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 4.3 Fold the attachment plate down on its hinge. See Fig. 8 4.4 Install the M4 knurled thumb screw by hand. See Fig. 8. DO NOT USE TOOLS TO TIGHTEN THIS SCREW. M4 Knurled Thumb Screw...
- Page 8 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 Place the plastic trim cover in position over the ceiling plate and press the Velcro tabs together. After completing step #5.3, screw the longer shaft with the locking nut and washer into the center threaded bushing on the ceiling plate as far as it will go. (See Fig. 9) Tighten the locking nut against the ceiling plate using a 3/4 ”...
- Page 9 It will curve back by its own spring action to wrap around itself enough to close the gap. (See Fig. 12) 8.3 If the projector is hung at a sharp angle, you may trim the collar for a better fit. (See Fig. 13) FIGURE 12 FIGURE 13 DO NOT RUN THE AC POWER CORD INSIDE THE PLASTIC TRIM COLLAR.
- Page 10 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 PROCEDURE FOR SERVICING LAMP HOUSING OR AIR FILTER: A. Remove the knurled thumb screw. See Fig. 14. The projector will swing down on the hinge of the mounting bracket. The bottom of the projector will now be in a position to permit servicing the lamp assembly.
- Page 11 INSTALLATION INSTRUCTIONS CEILING BRACKET AN-CM270 DIMENSIONS AND MEASUREMENTS OF COMPONENTS FOR SHARP MOUNTING BRACKET AN-CM70 CEILING PLATE 4 ” WIDE X 18 ” LONG DISTANCE BETWEEN SETS OF MOUNTING HOLES: 1st SET 12 ”, 2nd SET 14 ”, 3rd SET 16 ”...
-
Page 12: One-Year Limited Warranty
In no event shall SHARP be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone other than SHARP.