Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
®
Tecra
Resource Guide
Keep this guide in a convenient place to access important
information about your computer.
If you need assistance:
❖
Toshiba's Support Web site
pcsupport.toshiba.com
❖
Toshiba Global Support Centre
Calling within the United States (800) 457-7777
Calling from outside the United States (949) 859-4273
Please fill in for your reference and future use:
Model name______________________________________
Part number______________________________________
Serial number____________________________________
A7 Series
Advertisement
Table of Contents
Related Manuals for Toshiba Tecra A7-ST5112
Summary of Contents for Toshiba Tecra A7-ST5112
- Page 1 Resource Guide Keep this guide in a convenient place to access important information about your computer. If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273...
-
Page 2: Table Of Contents
Contents Introduction ..................19 Setting up your computer and getting started........21 Adding memory (optional)..............25 Your computer’s TFT display ............. 31 Inserting a PC Card................31 Removing a PC Card................. 32 Learning the basics................32 Using the TouchPad™ ............... 33 Using the optical drive .............. - Page 3 ALTERED OR LOST DUE TO ANY TROUBLE, FAILURE OR MALFUNCTION OF THE HARD DISK DRIVE OR OTHER STORAGE DEVICES AND THE DATA CANNOT BE RECOVERED, TOSHIBA SHALL NOT BE LIABLE FOR ANY DAMAGE OR LOSS OF DATA, OR ANY OTHER DAMAGE RESULTING THEREFROM. WHEN COPYING OR TRANSFERRING YOUR DATA, PLEASE BE SURE TO CONFIRM WHETHER THE DATA HAS BEEN SUCCESSFULLY COPIED OR TRANSFERRED.
- Page 4 ANY CRITICAL APPLICATIONS. IF YOU USE THE COMPUTER PRODUCTS IN A CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE. EU Declaration of Conformity TOSHIBA declares that this product conforms to the following Standards: Supplementary *The product complies with the Information:...
- Page 5 Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR-21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
-
Page 6: Device Authorization
2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment. -
Page 7: Radio Approvals For Wireless Devices
The Name of the radio equipment: refer to the equipment label provided on the computer JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖... - Page 8 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
- Page 9 802.11a (5 GHz) Australia Austria Belgium Canada Denmark Finland France Germany Greece Ireland Italy Liechtenstein Luxembourg Netherlands New Zealand Norway Portugal Sweden Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries European Community 5150-5250 MHz 5250-5350 MHz...
- Page 10 ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands. This device will operate under the control of the Access Point in order to avoid operating on a channel occupied by any radar system in the area.
- Page 11 Sweden Switzerland Uruguay Venezuela Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
- Page 12 Always use Bluetooth cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA computer product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information.
-
Page 13: Bluetooth Wireless Technology And Your Health
The radiated output power of the Bluetooth Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized. -
Page 14: Regulatory Statements
Regulatory statements This product complies with any mandatory product specification in any country/region where the product is sold. In addition, the product complies with the following: European Union (EU) and EFTA This equipment complies with the R&TTE directive 1999/5/EC and has been provided with the CE mark accordingly. - Page 15 2. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. 3. Contact TOSHIBA Direct PC if you have problems with interference caused by this product to Other Radio Stations. 2. Indication The indication shown below appears on this equipment.
- Page 16 CD-RW drive, Multi-drive or any other optical drive. You could damage the drive. You would also be exposed to laser light or other safety hazards, resulting in serious injury. Always contact an authorized Toshiba service provider, if any repair or adjustment is required.
- Page 17 This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
- Page 18 TouchPad is a trademark of Synaptics, Inc. Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Toshiba is under license. Other trademarks and trade names are those of their respective owners.
-
Page 19: Introduction
(RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its notebook component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process. - Page 20 Introduction Safety icons This guide contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
-
Page 21: Setting Up Your Computer And Getting Started
For accessory information, visit Toshiba’s Web site at accessories.toshiba.com. Setting up your computer and getting started The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day. -
Page 22: On Your Computer
Setting up your computer and getting started Never place a heavy object on the computer and be careful not to drop a heavy object onto the computer. It could damage the computer or cause system failure. Your computer’s features and specifications Certain notebook chassis are designed to accommodate all possible configurations for an entire product Series. - Page 23 TOSHIBA Battery Charger (that may have been provided with your computer), or use AC adaptors and battery chargers specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the computer, possibly resulting in serious injury.
-
Page 24: Connecting A Printer
Setting up your computer and getting started Plug the AC adaptor cord into the DC-IN on the back of the computer. (Sample Illustration) Connecting the AC adaptor cord to the computer Connect the power cord/cable to a live electrical outlet. The AC power light on the indicator panel glows green. -
Page 25: Adding Memory (Optional)
Adding memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com. Your computer comes with enough memory to run most of today’s popular applications. You may want to increase the computer’s memory if you use complex software or process large amounts of data. - Page 26 Adding memory (optional) Installing a memory module with the computer’s power on may damage the computer, the module, or both. The computer has two memory slots—Slot A and Slot B. You can install one or two memory modules. Before you install or remove a memory module, turn off the computer using the Start menu.
-
Page 27: The Computer
Adding memory (optional) Using a small Phillips screwdriver, unscrew the screw that secures the memory module slot cover. Front of computer (Sample Illustration) Unscrewing the memory module slot cover Remove the memory module slot cover. Place the screw and the cover in a safe place so that you can retrieve them later. - Page 28 Adding memory (optional) If your system has the memory modules stacked on top of one another, you must remove the top module before removing/installing the bottom module. 11 Pick up the memory module by its sides, avoiding any contact with its connector. Position the module toward the socket, aligning the connector’s notch with the matching key in the socket.
- Page 29 Adding memory (optional) 13 Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket. These latches should “snap” into place securely with the corresponding cutouts in the side of the module.
-
Page 30: Removing A Memory Module
Adding memory (optional) 17 Reconnect the cables. 18 Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Removing a memory module If you need to remove a memory module: Complete steps 1–8 in “Installing a memory module” on page 25 to shut down the computer and open the memory module slot cover. -
Page 31: Your Computer's Tft Display
Your computer’s TFT display Reconnect the cables. Restart the computer. TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. Your computer’s TFT display Small bright dots may appear on your screen display when you turn on your computer. -
Page 32: Removing A Pc Card
Removing a PC Card When the card is almost all the way into the slot, push firmly but gently to ensure a firm connection with the computer. Do not force the card into position. Removing a PC Card Be sure to disable the PC Card prior to removing it. Otherwise, the system may be damaged. -
Page 33: Using The Touchpad
Using the TouchPad™ ❖ Scan all new files for viruses. ❖ Do not turn off the computer if a drive indicator light indicates a drive is active. ® The Windows operating system records information, such as your desktop setup, during its shutdown procedure. If you do not let the ®... -
Page 34: Using The Optical Drive
Using the optical drive Control buttons When a step instructs you to click or choose an item, move the cursor to the item, then press and release the primary (left-hand) button. To double-click, press the primary button twice in rapid succession. The primary button usually corresponds to the left mouse button. -
Page 35: Inserting A Compact Disc
Using the optical drive Your optical drive may look like this: Drive in-use indicator light Eject button Manual eject hole (Sample Illustration) Optical drive Drive in-use indicator light—Indicates when the drive is in use. Eject button—Press to release the disc tray. Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. - Page 36 If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
-
Page 37: Moving The Computer
Moving the computer Removing a disc with the computer on To remove a disc (CD or DVD) with the computer turned on: Press the eject button on the drive. Do not press the eject button while the in-use indicator light is glowing. -
Page 38: Mobile Computing
Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while the computer is consuming full power. -
Page 39: Monitoring Main Battery Power
Mobile computing Monitoring main battery power The computer’s main battery light gives you an indication of the main battery’s current charge: ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows green when the main battery is fully charged ❖... -
Page 40: Changing The Main Battery
Mobile computing Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. - Page 41 Mobile computing Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock Slide the battery release latch to release the battery. Pull the discharged battery out of the computer. (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately.
-
Page 42: Taking Care Of Your Battery
Taking care of your battery Inserting a charged battery To insert a battery: Wipe the terminals of the charged battery with a clean cloth to ensure a good connection. Insert the charged battery into the slot until the latch clicks. The battery has been designed so that you cannot install it with reverse polarity. -
Page 43: Maximizing Battery Life
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries. -
Page 44: Disposing Of Used Batteries
Taking care of your battery Charge the battery pack until the battery light glows green. ❖ If you have extra battery packs, rotate their use. ❖ If you will not be using the system for an extended period, more than one month, remove the battery pack. ❖... -
Page 45: If Something Goes Wrong
If you cannot find the information you need elsewhere, call Toshiba at: (800) 457-7777. Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle, a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-822-8837. - Page 46 If something goes wrong To power off your computer, do one of the following: If you are not connected to a domain server: Click Start, Turn off computer. The Turn off computer window appears. Click Turn Off. The computer turns off. If you are connected to a domain server: Click Start, Shut down.
- Page 47 If something goes wrong Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adaptor and power cord/cable properly or installed a charged battery. Press and hold the power switch for at least 10 seconds.
-
Page 48: Display Problems
If something goes wrong Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing simultaneously. - Page 49 If something goes wrong Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology.
-
Page 50: If You Need Further Assistance
If the problem occurs while you are running a program, consult the program’s documentation for troubleshooting suggestions. Contact the software company’s technical support group for their assistance. For the number of a Toshiba dealer near you, see “Toshiba voice contact” in this section. - Page 51 If you need further assistance Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. Toshiba’s Technical Support Web site For technical support, or to stay current on the most recent...
-
Page 52: Power Cord/Cable Connectors
(BS approved) NEMKO approved) approved) Features and specifications For the complete detailed specifications for your computer, visit pcsupport.toshiba.com. Go to the Tech Support Center, select your particular model from the list and go to the Detailed Specifications for that model. -
Page 53: Index
Index display problems AC adaptor screen is blank AC power light alarms eject button low battery optical drive error messages backing up program has performed an illegal files operation battery alarms files changing backing up installing 40, 42 saving real-time clock (RTC) removing buttons inserting... - Page 54 Features and specifications TouchPad printer connecting tips on computing problem solving Toshiba Accessories computer hangs when PC Card information inserted TouchPad computer will not start using 33, 34 contacting Toshiba 50, 51 display is blank...
- Page 56 PMA500222011 09/06...