HP D7171A - NetServer - LPr Installation Manual
Third-party racks installation
Hide thumbs
Also See for D7171A - NetServer - LPr:
- Installation manual (182 pages) ,
- User manual (126 pages) ,
- Upgrade manual (97 pages)
Related Manuals for HP D7171A - NetServer - LPr
Summary of Contents for HP D7171A - NetServer - LPr
-
Page 1: Installation Guide
HP NetServer LT 6000r Installation Guide Third-Party Racks HP Part Number 5969-5914 Printed in January 2000... -
Page 2: Audience Assumptions
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not furnished by Hewlett-Packard. -
Page 3: Table Of Contents
Contents 1 Introduction ....................1 Installation Basics – Safety Precautions ............1 HP Net Server Rack-Mount Parts List............2 Definition of Terms..................2 2 Prepare the HP NetServer for Rack Mounting ........... 3 Introduction ....................3 Prepare the Rack................... 3 Mark the Rack Using the Template.............. -
Page 5: Introduction
1 Introduction This document describes how to mount an HP NetServer LT 6000r into third-party racks. Refer to the HP NetServer LT 6000r User Guide that came with the HP NetServer for instructions on adding accessories to, and configuring the HP NetServer. If you have an HP Rack System/E, HP Rack System /U or an older HP Rack System, See Chapter 8 and Chapter 13 of the HP NetServer LT 6000r Installation Guide for alternative rack mount instructions. -
Page 6: Hp Net Server Rack-Mount Parts List
Chapter 1 Rack Mounting the HP NetServer Maintain reliable grounding of rack-mounted equipment. Pay particular attention to supply connections that are not direct connections to the branch circuit (for example: power strips). HP Net Server Rack-Mount Parts List Make sure that the rack-mount kit that comes with your HP NetServer LT 6000r contains with the following parts. -
Page 7: Prepare The Hp Netserver For Rack Mounting
2 Prepare the HP NetServer for Rack Mounting Introduction This chapter describes how to prepare the HP NetServer and third-party rack for rack mounting. Prepare the Rack Before mounting the server, plan the server’s location in the rack relative to the other rack components. -
Page 8: Mark The Rack Using The Template
Chapter 2 Prepare the HP NetServer for Rack Mounting Mark the Rack Using the Template Use the rack-mounting template (for HP Rack System/E) to mark four EIA units for positioning the HP NetServer LT 6000r in the rack. 1. Mark the front mounting holes. a) Hold the template along side the front face of the left-front rack column. - Page 9 Chapter 2 Prepare the HP NetServer for Rack Mounting Location Marks on the Rack’s Front Columns 2. Repeat steps 1 through 3 for the left and right rear columns.
-
Page 10: Install The Slides In The Rack
Chapter 2 Prepare the HP NetServer for Rack Mounting Install the Slides in the Rack This section explains how to install the HP NetServer LT 6000r slides in the rack. NOTE The right slide is embossed with an R on the outside. The left slide is embossed with an L. -
Page 11: Remove The Bezel Adapters
Chapter 2 Prepare the HP NetServer for Rack Mounting 1. Loosen the adjustment knob on one side, insert the rear rack pins into the holes you marked on the outside rear column, and hold them in position. 2. While holding the slide in the rack, pull out the front bracket to the outside front column using the grip on the slide;... -
Page 12: Remove The Right Bezel Adapter
Chapter 2 Prepare the HP NetServer for Rack Mounting Control Panel Cable Clip Control Panel Cable Right Bezel Adapter Remove the Bezel Remove the Right Bezel Adapter Remove the right bezel adapter from the bezel. 1. Push in the tab on the adapter with a screwdriver. 2. -
Page 13: Remove The Left Bezel Adapter
Chapter 2 Prepare the HP NetServer for Rack Mounting Remove the Left Bezel Adapter Remove the left bezel adapter from the HP NetServer. 1. Pull the adapter top upward to pull it free of the slot on the HP NetServer. 2. - Page 14 Chapter 2 Prepare the HP NetServer for Rack Mounting To prevent the rack from rolling while you mount the HP NetServer LT 6000r, make sure that the leveler screws (if any) on the rack’s lower four corners are in firm contact with the floor.
- Page 15 Chapter 2 Prepare the HP NetServer for Rack Mounting WARNING The HP NetServer LT 6000r weighs up to 100 pounds. At least two people must be on hand to lift the server into position. Failure to observe this warning could result in serious injury to you or to the HP NetServer LT 6000r.
-
Page 16: Attach The Cable Management Arm
Chapter 2 Prepare the HP NetServer for Rack Mounting 7. Release the slide locks and push the mounted server into the rack. The server will lock into place. Push the server to the second notch on the blue rack-latch position closest to the bezel. The first latch position is used when mounting the HP NetServer LT 6000r in a HP rack. -
Page 17: Continue With The Rack Installation Process
Chapter 2 Prepare the HP NetServer for Rack Mounting Chassis Chassis Bracket Nuts Attach the Cable Management Arm 3. Extend the HP NetServer out of the rack to ensure the Cable Management Arm moves along with the chassis without binding. NOTE Refer to the HP NetServer LT 6000r Cabling Reference Guide, for information about cable dressing and routing. -
Page 19: Warranty And Support
3 Warranty and Support The hardware warranty below applies to components purchased as accessories. If your component was factory installed as part of an HP NetServer model, refer to the HP NetServer Warranty and Service/Support Booklet provided with your system documentation for the warranty limitations, customer responsibilities, and other terms and conditions. -
Page 20: Hp Repair And Telephone Support
Chapter 3 Warranty and Support HP Repair and Telephone Support Refer to the HP NetServer Warranty and Service/Support Booklet supplied with your HP NetServer system documentation for instructions on how to obtain HP repair and telephone support. -
Page 21: Index
Index Cable management arm, attaching, 16 Rack Mounting Template, 8 Rack-Mount Parts List, 6 Definition of Terms, 6 Safety Precautions, 5 service, 20 Install the Slides, 10 support, 20 Prepare the Rack for Mounting, 7 warranty, 19...