HP Z210 Series Rack Mounting Instructions
Hp z200, z400 and xw4000 workstations - rack mount tray installation
Hide thumbs
Also See for Z210 Series:
- Maintenance and service manual (185 pages) ,
- User manual (68 pages) ,
- Support manual (22 pages)
Table of Contents
Advertisement
Quick Links
Rack mount tray installation
Introduction
This document describes how to install the HP Z200 and Z210, Z400, and xw4000 series
Workstations into a rack mount tray. It also describes how to mount the workstation-tray assembly into
a rack.
Kit contents
Rack mount tray
●
Adapter brackets
●
Rails and mounting hardware (installation instructions in Appendix A of this document)
●
Installation instructions
●
Warranty information
●
Required tools
T-15 Torx screwdriver
●
T-20 Torx screwdriver
●
Cross-tip screwdriver
●
ENWW
© 2011 Hewlett-Packard Development Company, L.P. Printed in the U.S.
Introduction
1
Advertisement
Table of Contents
Related Manuals for HP Z210 Series
Summary of Contents for HP Z210 Series
-
Page 1: Kit Contents
Rack mount tray installation Introduction This document describes how to install the HP Z200 and Z210, Z400, and xw4000 series Workstations into a rack mount tray. It also describes how to mount the workstation-tray assembly into a rack. Kit contents Rack mount tray ●... -
Page 2: Warnings And Cautions
Warnings and cautions WARNING! Any surface or area of the equipment marked with this symbol indicates the presence of an electrical shock hazard. To reduce the risk of injury from electrical shock, do not open any enclosed area marked with this symbol. WARNING! To reduce the risk of electric shock or damage to your equipment: —... -
Page 3: Step 1-Preparing The Workstation
Step 1—Preparing the workstation NOTE: All illustrations are examples only. Workstation models vary. For product-specific information, see the service guide for your HP workstation at http://www.hp.com/support/manuals before beginning installation. To prepare the workstation for component installation: Power down the workstation, and then disconnect the power cord. Power down all external devices, and then disconnect them from the workstation. - Page 4 Step 3—Attaching the rack mount tray to the workstation Using a T-15 Torx screwdriver, remove the indicated chassis screw (1), if present, from the rear of the workstation. Some workstation models do not use the chassis screw as shown. Figure 2 Removing the chassis screws To prepare the tray: Select the adapter bracket with the label that matches your workstation model.
- Page 5 To install the workstation on the tray: Guide the front bezel of the workstation under the lip of the adapter bracket (1). Rotate the back of the workstation down onto the tray (2). Tighten the single, black rear captive screw (3), to secure the rear of the workstation into the tray.
- Page 6 Ensuring that the rail-bracket shelf (2) is engaged by the lip on the underside of the tray (3), slide the assembly into position in the rack. Figure 5 Loading the workstation into the rack Secure the assembly into the rack by tightening the silver captive screws (1). Figure 6 Completing installation NOTE:...
-
Page 7: Step 5-Completing Installation
Step 5—Completing installation Reconnect power to the workstation. Restore power to the workstation. Step 5—Completing installation ENWW... - Page 8 HP Depth-Adjustable Fixed Rails Rack Option Kit installation instructions Introduction The HP Depth-Adjustable Fixed Rails Rack Option Kit allows the user to install depth-adjustable fixed rails in racks from 19 inches (48.26 cm) to 31 inches (78.74 cm) in depth. Once installed, these depth- adjustable fixed rails can be used to support a variety of rack-mountable devices.
-
Page 9: Rack Considerations
Rack considerations Before beginning these procedures, be sure you understand and follow these precautions: WARNING! To reduce the risk of personal injury or damage to the equipment be sure that: ● The leveling jacks are extended to the floor. ● The full weight of the rack rests on the leveling jacks. ●... - Page 10 Install cage nuts into the rear locations of the rack that best align with the bottom two holes at the rear of the depth-adjustable fixed rail, ensuring they are installed level with the front. Insert two screws through each depth-adjustable fixed rail and into the cage nuts installed earlier, securing the rail to the rear of the rack.