Honeywell Thor VM2 Quick Start Manual
Vehicle-mount computer
Hide thumbs
Also See for Thor VM2:
- User manual (398 pages) ,
- Reference manual (196 pages) ,
- Quick start manual (12 pages)
Related Manuals for Honeywell Thor VM2
Summary of Contents for Honeywell Thor VM2
- Page 1 Thor™ VM2 Vehicle-Mount Computer ® ® With Microsoft Windows Embedded CE 6, Windows Embedded ® ® Standard 2009, Windows 7 Professional, and Windows Embedded Standard 7 Operating System Quick Start Guide VM2-QS Rev B 7/14...
- Page 2 The Thor VM2 can be connected to vehicle power as follows: • Direct power connection (12-48VDC vehicles). See Connecting the Power Cable, below. • Replace a previously installed VX6/VX6 or Thor VX8/VX9 with an adapter cable. See Adapter Cables, below.
- Page 3 • Choose a mounting location so that the power cable does not extend outside the vehicle and that provides sufficient clearance so that the power cable (especially the dock connector end) is not pressed against part of the vehicle. • Regularly inspect power cable for damage, especially in low temperature environments.
- Page 4 Power Cable Installation 1. The Thor VM2 must not be mounted in the Quick Mount Smart Dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock.
- Page 5 Screen Blanking box, or to the Thor VM2 User’s Guide, available at www.honeywellaidc.com for fur- ther information about the Screen Blanking box.) 11. Press the power switch on the back of the Thor VM2 dock. 12. Press the power button on the front of the Thor VM2.
- Page 6 VX6 or VX7 power con- nection installation. This adapter cable is available to attach the Thor VM2 to a vehi- cle previously equipped with a VX6/VX7 DC power cable. When this adapter cable is used, there is no provision for an ignition switch input.
- Page 7 VX8/VX9 DC power cable. This cable has bare wires for ground and ignition sense connection plus a D9 cable that connects to a COM port on the Thor VM2 dock to provide a screen blanking signal.
- Page 8 9. Secure the power cable to the Thor VM2 using strain relief cable clamps, and place the Thor VM2 in the dock.
- Page 9 10. If using the Screen Blanking feature, install the screen blanking box or switch. 11. Press the power switch on the back of the Thor VM2 dock. 12. Press the power button on the front of the Thor VM2. Note: Have the following information available before setting up your Thor VM2: •...
- Page 10 ActiveSync using USB-Client Connection The only connection type is USB Client. 1. Connect the Thor VM2 end of the USB cable to the USB port on the back of the Thor VM2 Quick Mount Smart Dock. 2. Connect the other end of the cable to a USB port on a PC or laptop.
- Page 11 Refer to the Thor VM2 User’s Guide, available at www.honeywellaidc.com, for further information about ActiveSync information. Wireless Network Configuration If the access point uses an authentication protocol (WEP, LEAP, etc.), your radio must use the same authentication. Contact your IT department for any necessary keys, login credentials, or certificates.
- Page 12 Reboot the Thor VM1. Setting Up AppLock (CE 6.0 only) Thor VM2 devices are shipped to boot in Administration mode. In this mode, the user has full access to the device and no password is needed. After the administrator completes the process below, the Thor VM2 switches to end-user mode and restricts access to only the specified application(s).
- Page 13 1. Make sure the mobile client network settings are properly configured. If you are connecting via WLAN (802.11x), make sure your Thor VM2 is connected to the network. 2. Launch RFTerm by tapping the RFTerm icon on the desktop. 3. Select Session > Configure from the application menu and select the host type.
- Page 14 To reboot the Thor VM2 with all other Windows operating systems: 1. Select Start > Shutdown > Restart to reboot. When the Thor VM2 is booting, there may be small delays while the wireless client connects, applications launch, remote management...
- Page 15 Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made. The information in this publication does not represent a commitment on the part of HII.
- Page 17 Free Manuals Download Website h p://myh66.com h p://usermanuals.us h p://www.somanuals.com h p://www.4manuals.cc h p://www.manual-lib.com h p://www.404manual.com h p://www.luxmanual.com h p://aubethermostatmanual.com Golf course search by state h p://golfingnear.com Email search by domain h p://emailbydomain.com Auto manuals search h p://auto.somanuals.com TV manuals search h p://tv.somanuals.com...