Page 1
Thor VM3 Vehicle-Mount Computer with Microsoft® Windows® 7 Professional for Embedded Systems with Microsoft® Windows® Embedded Standard 7 User Guide...
Page 2
Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document without prior notice, and the reader should in all cases consult HII to determine whether any such changes have been made.
Front View - Thor VM3 ..........................15 Back View - Thor VM3 ..........................16 Access Panels - Thor VM3 ........................17 Front View - Dock ............................17 Back View - Dock ............................18 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 4
Uninterruptible Power Supply ......................27 Backup Battery ............................29 Fuse ................................29 Power Management Modes........................29 Power Controls............................31 External Connectors ............................33 Serial Connector (COM1 and COM2) ....................33 USB Connector(s) .............................34 Ethernet Connector ..........................34 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 5
Procedure - RAM Mount Assembly....................58 Install U Bracket Mount..........................69 Components - U Bracket Mounting Assembly................69 Procedure - U Bracket Assembly ......................70 Connect Cables ..............................73 Strain Relief Cable Clamps ........................73 Connect Power............................74 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 6
Drive C Folder Structure........................131 Control Panel ..............................134 About................................134 Bluetooth Printing ..........................136 Bluetooth Scanning ..........................139 Display................................ 143 Enterprise Settings ..........................143 External Keypad............................148 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 7
Dynamic vs. Fixed IP Address ......................193 Important Notes ............................. 193 Using the Wireless Configuration Utility..................194 Creating a Profile ........................... 198 Advanced Profile Configuration....................... 199 Roam Management ..........................222 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 8
VM3D and VMXD Enhanced Dock....................264 Environmental Specifications......................... 265 Thor VM3 and Dock..........................265 Network Card Specifications ........................266 WLAN - Qualcomm Atheros 802.11a/b/g/n ................266 viii Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 9
CANbus / Audio Connector ....................... 274 Hat Encoding ..............................277 Licenses of Third Party Software ......................279 Appendix C - Thor VM3 Agency Information............329 Label Locations ............................329 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 10
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
With the Portal, you can submit and track your questions online and send and receive attachments. Telephone: www.honeywellaidc.com/locations For our latest contact information, please check our website at the link above. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The duration of the limited warranty for the Thor VM3 is 1 year. The duration of the limited warranty for the Thor VM3 Dock is 1 year. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 13
The duration of the limited warranty for the Thor VM3 Vehicle Mount Assembly is 1 year. The duration of the limited warranty for the Thor VM3 internal UPS battery is 1 year. The duration of the limited warranty for the Thor VM3 AC power supply and cables is 1 year.
Page 14
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The Thor VM3 contains a UPS battery which, when fully charged, can power the Thor VM3 for a minimum of 30 minutes. This can be when the Thor VM3 is not attached to a dock or when the Thor VM3 is attached to a dock but the vehicle power is interrupted, such as when the vehicle battery is being changed.
• RAM or U-Bracket vehicle mount kit If you ordered additional accessories for the Thor VM3, verify they are also included with the order. Keep the original packaging material in the event the Thor VM3 should need to be returned for service. For details, see Product Service and Repair.
8. Press the Power Button on the Thor VM3. Note: After the initial power on, the Thor VM3 can be configured to automatically power on, either when power is attached or the vehicle ignition is turned on. 9. Perform Touch Screen Calibration (not required for PCAP touch screen).
Embedded 7 operating system, the product key is printed on a decal on the rear of the Thor VM3. It may be necessary to remove the Thor VM3 from the dock to view the prod- uct key decal. Under normal circumstances, it is not necessary to re-enter the product key as it was entered during the manufacturing process.
VMXD Enhanced Dock for Off-Vehicle Use All docks provide: • A mount for the Thor VM3 computer. The dock attaches to a vehicle via a RAM or U- bracket mount or to a RAM table stand for use in an office environment. •...
Honeywell external keyboards. Ethernet CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
RJ-45 Ethernet connection on top of dock. CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Caution: This dock is designed for DC power vehicle-mounted applications only. This dock is designed for use when the Thor VM3 is replacing a Thor VX8 or Thor VX9. This dock utilizes the existing vehicle wiring from the earlier computer and supports screen blanking through that wiring.
RJ-45 Ethernet connection on top of dock. CANbus CANbus connection via an adapter cable Audio Headset connection via an adapter cable Screen Supported via COM1 and COM2 connectors. Blanking Ignition Supported Control Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Additional Connectors External antenna connectors may be present on the back of the Thor VM3. The connec- tors may include: • 802.11 antenna connectors, used when the Thor VM3 is not equipped with internal antennas. • External GPS antenna connector, when the Thor VM3 is equipped with GPS.
Components Front View - Thor VM3 Microphone Power Ambient Button Light Sensor Speakers Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Back View - Thor VM3 External Antenna Connectors WWAN Antenna Cable Access Panel Card mSATA Access Panel Provision for Dock Provision for Padlock Quick Release Handle Contact Laptop Security Pads Cable Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Front View - Dock Standard Dock Dock Contact Pads Enhanced Dock The Enhanced Dock has a foam surround around the dock contact pad. Dock Contact Pads Foam Surround Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
COM2 port on the dock. If a screen blanking box is not connected via the power cable, the COM1 port on the dock is available for a serial device Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
3. Press the Blue key to exit Blue mode. Refer to the Screen Control panel for the current display brightness level. Screen Blanking The Thor VM3 can be configured to blank (blackout) the display while the vehicle is in motion. Refer to ZoomZone for information.
These items can also be used to adjust speaker volume. Power Up If a USB drive, such as a thumb drive is attached to the Thor VM3, the device may attempt to boot from the USB drive. Remove the USB drive and power up the Thor VM3 again.
Select Start > Shut Down > Restart and tap OK to restart the Thor VM3. • Use the P1 + P7 + Orange key press sequence to reboot the Thor VM3. The keys must be pressed in sequence; they do not need to be held down simultaneously.
A stylus replacement kit is available. Note: The stylus is different for a Thor VM3 with a PCAP touch screen and one with a resistive touch screen. Be sure the stylus is the correct type for the touch screen installed in the device.
Note: These instructions are for components made of glass. If there is a removable protective film sheet on the display, remove the film sheet before cleaning the screen. Keep rough or sharp objects away from the Thor VM3 touch screen and, if installed, the bar code reader scanning aperture.
Page 34
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
CHAPTER HARDWARE OVERVIEW System Hardware 802.11a/b/g/n Wireless Client The Thor VM3 has an 802.11a/b/g/n network card that supports diversity with two internal or external antennas. Power management for the network card is configured with the WLAN Wireless Configuration Utility (WCU).
When a headset is plugged into the adapter cable, the main speakers are disabled. A microphone is located at the upper right of the Thor VM3 display, near the Thor VM3 emblem. When a headset is plugged into the adapter cable, the internal microphone is disabled.
Universal Input Power Supply can be used to convert AC wall power to an appropri- ate DC level. AC to DC power input for the Thor VM3 is delivered to the dock via an optional external power supply and adapter cable. See External AC/DC Power Supply.
Page 38
Move the Thor VM3 to a different location to charge the UPS battery. When the Thor VM3 is operated in an environment where the UPS battery is not able to charge due to temperature extremes, the Thor VM3 should be removed to a location within the safe charging temperature range during off hours.
The Thor VM3 has four power modes: Full On, Sleep, Hibernate and Off. Full On Mode When the Thor VM3 is attached to either vehicle power or an external power supply or is operating from the UPS battery and the power button is pressed, the Thor VM3 is in the On mode.
If the Thor VM3 is Full On, a press of the power button can be configured to put the unit in Standby. See the Choose What the Power Button Does. Sleep Mode When the sleep timer expires without a primary event occurring, the Thor VM3 transi- tions to Sleep mode.
(options may vary by OS type): • Ignore power button press • Prompt the user to select action • Shut down (default, an orderly shutdown is performed) • Standby/Sleep • Hibernate Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 42
“Plugged In” power management timeouts are used, Ignition Control The Thor VM3 is configured to power on when the vehicle ignition is switched on. When either Ignition Control/Ignition On or Ignition Control/Ignition Off is selected and external power is present, the Thor VM3 uses the “Pugged In”...
Power the Thor VM3 off before attaching a cable to any port (serial, USB, Audio/CAN, etc.). The external I/O connectors for the Thor VM3 are located on the right side of the dock (when viewed from the back). Power Supply Connector is on the left side of the dock (when viewed from the back).
An additional USB host port is located on the top of the Enhanced Dock. Lift the cover to access the USB port. Ethernet Connector An Ethernet port is located on the top of the Enhanced Dock. Lift the cover to access the Ethernet port. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Power Supply Connector for connector pin- Standard Dock Enhanced Dock out detail. See Connect Power for more infor- mation on connecting power to the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The external antennas can be remotely mounted on the vehicle. See Install Remote Antenna for instructions. External antenna kits are available for the 802.11 Wi-Fi radio, GPS and WWAN. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The integrated keypad backlight and the display share the same timer, which is configured in the Power Options control panel. • The integrated keypad backlight can be disabled via the Options control panel. Keypad LEDs Keyboard LEDs for details. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Ctrl Enter The Thor VM3 uses an optional rugged QWERTY 95 key keyboard, designed for ease of use with the Windows operating system. The USB keyboard connects directly to the D9 USB connector (Standard Dock) or USB1 connector (Enhanced Dock).
Page 49
21-key Numeric Keypad A numeric keypad is available for the Thor VM3 in applications where a full keyboard may not be needed. The USB keyboard connects directly to the D9 USB connector (Standard Dock) or USB1 connector (Enhanced Dock).
PS/2 Keyboards Legacy PS/2 keyboards can be used with the Thor VM3 via a USB to PS/2 adapter cable. PS/2 keyboards are available in 60-key and 95-key versions and were used with the VX6, VX7, Thor VX8 or Thor VX9.
Page 51
However these keys send distinctly different scan codes when the keys are pressed. The default codes for the Thor VM3 number keys cor- respond to the numeric keypad on standard keyboards. In order to duplicate the codes sent when the alphanumeric key is pressed, the hidden keystroke must be used.
Page 52
F4 and F5 keys are not used as the display brightness is adjusted via the buttons on the Thor VM3. • The 2 functions of the F6 and F7 keys are not used as the Thor VM3 has TFT LCD screen with no provision for contrast adjustments. • The 2 functions of the F8 and F9 keys are not used as the sound volume on the Thor VM3 is controlled with the Sound icon in the Microsoft Windows System Tray.
BkSp to enter the Insert (Ins) mode. USB Keyboard / Mouse A standard USB keyboard or mouse can be attached to the Thor VM3 using the appro- priate adapter cable. The Y cable attaches to the Thor VM3 and provides a USB connector. Please refer to documentation provided with the USB keyboard or mouse for more information on their operation.
System State • Solid Green • On but Backlight Off • On but Display Off • External power present • Hibernate External power not present • Standby/Sleep • Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Charge timeout • UPS is not installed SSD (Solid State Drive) LED LED Behavior Status Flashing Green SSD read or write activity No SSD read or write activity Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Indicates a connection with an IP address to an Access Point Indicates no connection to an Access Point Bluetooth LED LED Behavior Status Bluetooth hardware is on Bluetooth hardware has been turned off Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Pressing the Blue key exits the Orange mode and turns off the Orange LED Orange mode is not invoked. Programmable LED The Programmable LED is available for user applications. The LED defaults to Off unless activated by user application. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Technical Assistance for availability. Note: If the touch screen is disabled or loses calibration on a Thor VM3, you must use a USB mouse or keyboard attached to the Thor VM3 to access the control panel to re-enable or recalibrate the touch screen unless a programmable key has been assigned to that function.
Display Backlight Control The display brightness on a Thor VM3 equipped with an outdoor display can be config- ured to automatically adjust depending on the ambient light level via Screen Control. Note: When automatic brightness control is enabled, the user can still manually adjust brightness.
Page 60
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
For an AC powered application: Use an AC/DC power supply and the VMXD off- vehicle enhanced dock. The Thor VM3 is designed to be mounted to a dock in a vehicle with either a RAM mount or U Bracket system. A power cable is provided with the Thor VM3 dock. An optional 21 key numeric or 95 key laptop-style USB keyboard and keyboard mounts are available.
Quick Start The following list outlines, in a general way, the process to follow when mounting the Thor VM3 in a vehicle. Refer to the following sections in this document for more details. Install RAM Mount Install U Bracket Mount to the vehicle.
1. Locate the notch on the upper rear of the Thor VM3. 2. Slide this notch over the top lip of the dock. Slide the Thor VM3 from side to side on the dock to make sure it fully engages on the lip of the dock. If the Thor VM3 cannot be slid side to side, the lip is engaged.
Page 64
When the Thor VM3 is placed in the dock, the following may happen: • If the Thor VM3 is off and power is connected to the dock, the Thor VM3 may boot when placed in the dock. The behavior depends on the Power Scheme selected. See Ignition Control/Ignition On and Auto-On.
Laptop Security Cable The Thor VM3 can be secured with a stan- dard laptop security cable using the slot on the back of the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
RAM Arm (Size D), length varies by kit selected One of three mounting options: • RAM Ball mount (Size D, may include 3 cone washers), or Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 67
Hardware (cone washers and nuts) to attach Ball to Plate Mounting Kits with Integrated Keyboard Mounting Additionally, the kits for the Thor VM3 with an integrated 95 key keyboard mount include: Thor VM3 Keyboard Mounting Bracket RAM Ball (Size C) with hardware (nuts) to attach RAM ball...
Equipment Needed: Sockets, screwdriver and a Torque wrench capable of measuring to 50 inch pounds (5.64±.56 N/m). Note: Torquing tool is not supplied by Honeywell. Tools needed to attach the RAM Clamp Mount to the vehicle are not supplied by Honeywell.
Page 69
1. Determine the position for mounting the RAM ball base. Be sure to position the RAM bracket to allow access to the switches and ports on the bottom of the Thor VM3. 2. Attach the RAM ball base to the vehicle mounting surface using three or four 1/4 bolts (not included) or equivalent fasteners.
Page 70
2” (50.8 mm) thick. The clamp may be attached to a thicker beam by substituting longer bolts (not included). Be sure to position the RAM clamp mount to allow access to the switches and ports on the bottom of the Thor VM3. Bolts...
Page 71
1. Determine the position for mounting the RAM ball plate. Be sure to position the RAM plate to allow access to the switches and ports on the bottom of the Thor VM3. 2. Attach the RAM ball plate to the vehicle mounting surface using four 1/4 bolts (not included) or equivalent fasteners.
Page 72
3. If using the external keyboard mount, position the Keyboard Bracket and the Size D RAM ball on the rear of the Thor VM3 dock, aligning the holes on the back of the Thor VM3 dock with the holes on the bracket and the RAM ball base.
Page 73
1. Slip the Size D RAM arm over the ball on the vehicle RAM mount (RAM Ball mount shown). 2. Insert the ball on the dock into the RAM arm and tighten the knob on the RAM arm using the supplied RAM wrench. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 74
If the Thor VM3 is not already mounted to the dock, Place Thor VM3 in the Dock If the optional external keyboard is not used, the mounting process is complete. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 75
Step 5 – Attach Alphanumeric Keyboard to Mounting Plate (Optional) Note: This step is only for a Thor VM3 with the optional external keyboard. If using the optional integrated keyboard mount, attach the keyboard to keyboard mounting plate, using four #8 screws, flat washers and lock washers.
Page 76
Note: This step is only for a Thor VM3 with the optional external keyboard. 1. Slip the Size C RAM arm over the ball on the Thor VM3 Keyboard Bracket. 2. Slip the ball on the Keyboard Mounting Plate into the other end of the Size C RAM arm.
Page 77
3. Slip the RAM arm over the accessory RAM ball. 4. Slip the RAM ball on the keyboard into the RAM arm. 5. Tighten the knob on the RAM arm while adjusting to the desired angle. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 78
4. Slip the RAM ball on the scanner holder into the RAM arm. 5. Tighten the knob on the RAM arm while adjusting to the desired angle. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
With a U Bracket included for new vehicle installations • Without a U Bracket for installing the Thor VM3 in place of a previous Honeywell vehicle mounted computer, such as a VX6 or VX7. U Bracket (only necessary for new installations)
The adapter bracket can be mounted in a high or low position, depending on viewing position, as shown below. Additionally, the slotted U bracket allows the Thor VM3 to be mounted vertically or tilted forward or backward for best viewing angle.
Page 81
5. 3.38 in / 85.85 mm 6. Vehicle Mount Footprint 7. 0.406 in / 10.312 mm 8. 0.88 in / 22.3 mm 9. 1.25 in / 31.75 mm Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 82
Step 2 - Remove RAM Ball If the Thor VM3 dock has a RAM ball attached, the RAM ball must be removed from the dock to use the U Bracket mount. Remove the RAM ball. The hardware used to attach the RAM ball to the dock is not reused for the U bracket mount.
Connect Cables There are many cables available for the Thor VM3 including power cables, and data/ communication cables. Strain Relief Cable Clamps Equipment Required: Phillips screwdriver (not supplied by Honeywell) There are five strain relief cable clamps secured to the Standard Dock.
- For applications where a Thor VM3 (with a VMXD Enhanced Dock) replaces a previously installed Thor VX8 or Thor VX9. When using the Thor VM3 with AC power, use the VMXD Enhanced Dock for Off-Vehi- cle Use and: •...
Page 85
The power cable is less flexible in low temperature environments. Avoid sharp bends. Caution: Regularly inspect power cable for damage, especially in low temperature environments. Contact Technical Assistance replacement cable options. Power Cable Routing Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 86
Note: Correct electrical polarity is required for safe and proper installation. See the figures below for additional wire color-coding specifics. The Thor VM3 DC input wires (Red, Red/White DC+ and Black, Black/White DC-) and the Blue ignition input wire are galvanically isolated. The Green ground input is used for electrostatic discharge (ESD) protection.
Page 87
Vehicle 10-60VDC Direct Power Connection 1. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 2. While observing the Fuse Requirements, connect the power cable as close as possible to the actual battery terminals of the vehicle (if using unswitched power).
Page 88
12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 89
For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 90
12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 91
For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 92
12VDC. • For 24VDC input, use the 6A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 24VDC. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 93
For 48VDC input, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than 48VDC. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 94
Caution: Use caution when routing the power cable. See Power Cable Cautions. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 95
Wiring Diagram, before beginning power cable install. 2. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way possible.
Page 96
+ and V - terminals. 8. Connect the ground (green) wire from the Thor VM3 to the GND terminal on the input side of the DC/DC power supply. 9. Route the wiring from the DC/DC power supply to the vehicle’s electrical system. Do not connect to vehicle power at this time.
Page 97
17. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
Page 98
For all voltages, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than the vehicle input voltage. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 99
Caution: Use caution when routing the power cable. See Power Cable Cautions. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 100
Wiring Diagram, before beginning power cable install. 2. The Thor VM3 must not be mounted in the dock. The power switch on the dock must be turned Off. The power cable must be UNPLUGGED from the dock. 3. Route the cable from the Thor VM3 to the DC/DC power supply. Route the power cable the shortest way possible.
Page 101
14. Use proper electrical and mechanical fastening means for terminating the cable. Properly sized “crimp” type electrical terminals are an accepted method of termination. Select electrical connectors sized for use with 18AWG (1mm conductors. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 102
16. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
Page 103
For all voltages, use the 3A fuse from the kit or a slow blow fuse that has a DC voltage rating greater than the vehicle input voltage. Note: For North America, a UL Listed fuse is to be used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 104
Enhanced Dock only. An adapter cable is available to attach the Thor VM3 to a vehicle previously equipped with a VX6/VX7 DC power cable. The adapter cable has a 5-pin connector to match with the VX6/VX7 power supply cable on one end and a 6-pin connector to match to the Thor VM3 on the other end.
Page 105
VM3 on the other end. The cable also has bare wires for ground and ignition sense con- nection plus a D9 cable to connect to a COM port on the Thor VM3 dock to provide a screen blanking signal. This section assumes the VX8/VX9 power cable is properly con- nected to vehicle power.
Page 106
7. Connect the watertight connector end of the power cable to the Thor VM3 dock power connector by aligning the connector pins to the power connector; push down on the watertight connector and twist it to fasten securely.
Page 107
CV61 DC power cable. The adapter cable has a 5-pin connector to match with the VV61 power supply cable on one end and a 6-pin connector to match to the Thor VM3 on the other end. This section assumes the CV61 power cable is properly connected to vehicle power.
Page 108
Honeywell Screen Blanking Box Cable An optional Honeywell Screen Blanking Box Cable is available. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 109
Connected to Screen Blanking Box, unswitched Connected to Switch side 8 (CTS) Connected to Screen Blanking Box, switched side Connected to Switch The user-supplied cable is installed as follows: Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
To pin 7 of COM1 or COM2 To pin 8 of COM1 or COM2 Note: The black and gray wire colors in the illustration only apply to the optional Honeywell Screen Blanking Box Cable, VM1080CABLE. The wire colors may be different in a user- supplied cable.
Page 111
COM1 or COM2 port on dock Pins 7 and 8 must be connected as shown in the illustration above. No other pins are to be connected. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 112
Determine the type of power supply used with the previous Thor VX8 or Thor VX9 instal- lation: • DC/DC Power Supply with Screws on Top of Lid • DC/DC Power Supply with Screws on Side of Lid Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 113
Supplied Power Cable Power (Shielding to be trimmed) Supply Caution: For battery powered vehicles: • + is connected to battery positive. • - must be connected to battery negative. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 114
+ is connected to battery positive. • - is connected to battery negative. • is connected to the vehicle chassis ground, which can also be battery negative. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 115
Caution: For battery powered vehicles: • + is connected to battery positive. • - must be connected to battery negative. • GND must be connected to the vehicle chassis ground. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 116
+ is connected to battery positive. • - is connected to battery negative. • GND is connected to the vehicle chassis ground, which can also be battery negative. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 117
Power Switch on the back of the Thor VM3 dock. 6. Press the Power Button on the front of the Thor VM3 to turn on the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 118
Table Stand When the Thor VM3 is used in an office environment, it can be mounted in a table stand. To use the table stand: 1. Attach the RAM ball to the RAM Metal Table Stand with the supplied screws and nuts.
1. Seat the keyboard cable connector over the USB or USB1 connector on the dock. 2. Tighten the thumbscrews in a clockwise direction. Do not over tighten. 3. Secure the cable to the Thor VM3 with Strain Relief Cable Clamps. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
A legacy PS/2 keyboard (used with VX6, VX7, Thor VX8 or Thor VX9), available in either 60-key or 95-key versions can be used with the Thor VM3 via a PS/2 to USB adapter cable. This function is only supported with the VM3D or VMXD Enhanced Docks. It is not supported with the VM1D Standard Dock.
Page 121
5. Secure the cable to the Thor VM3 with Strain Relief Cable Clamps. The strain relief must capture the keyboard cable. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
3. The USB-host connectors provide a connector for a USB device such as a USB thumb drive. 4. Secure the cables to the Thor VM3 with Strain Relief Cable Clamps. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 123
USB scanner, it may be necessary to unplug the scanner and plug it back into the USB port in order for the auto-detect function to display the scanner settings. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Connect USB Client Note: The USB client connection is not used on the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
1. The scanner cable is attached to either the COM1 or COM2 port on the dock. 2. Connect the serial cable for the scanner as directed above. 3. When the Thor VM3 is powered on, it provides power to the serial scanner. 4. Configure the Data Collection (DC) Wedge to manipulate scanned data as desired.
Page 126
Tuck the cable under the belt, but leave a small loop where it goes under the belt. • Do not wear the cable on the front of your body. It may get in your way or get caught on protruding objects. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
2. Place the antenna over the antenna connector. If only one antenna is used, be sure to connect it to the Wi-Fi Main connector. 3. Push down and twist the antenna base clockwise until secure. 4. Repeat for second antenna, if used. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The Vehicle Remote Mount Antenna cannot be used by devices with an internal antenna. Components and Mounting Diagram Washer Washer Bracket To antenna Antenna To antenna Bracket To antenna connector on computer Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
VM3. If only one antenna is used, be sure to connect it to the Wi-Fi Main connector. 7. Repeat the steps above for the second 802.11 antenna. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 130
6. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 131
5. Use cable ties to secure the coaxial cable to the vehicle as necessary. Make sure the cable is routed so it is not damaged by any moving parts of the vehicle. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Apply Touch Screen Protective Film The optional Thor VM3 touch screen protective film is shipped in packs of 10. The pro- tective film is flexible and treated with an anti-glare coating on the outer surface. The protective film is slightly larger than...
2. Lift up on the edge of the protective film so it does not slide between the touch screen and display housing when the protective film is slid back to the center. 3. Repeat until all edges are free and remove the protective film. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Torquing tool capable of measuring inch pounds • #2 Phillips screwdriver bit Disconnect Procedure 1. For convenience, the Thor VM3 can be removed from the dock, though it is not nec- essary. 2. If the Thor VM3 remains in the dock, disconnect the power cable from the dock.
SIM labels. This panel is on the right hand side when the Thor VM3 is face down with the top away from the user. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 136
11. Restart the Thor VM3. 12. When using Windows explorer to view My Computer, the mSATA expansion card is identified as Hard Disk Drive, usually Drive D:. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
VM3 WWAN Connection Manager for software configuration. Note: The SIM card is not hot-swappable. After installing or removing a SIM card, the Thor VM3 must be rebooted for the change to take effect. Equipment Required The following equipment is user-supplied: •...
Page 138
10. Lower the SIM holder to back to its flat position. 11. Slide the silver retainer clip back toward the outside edge of the Thor VM3. This locks the SIM card in place. 12. Reattach the access panel, torquing the screws to 7.0 ± 0.5 inch pounds.
Replace Front Panel Front Panel Options The front panel of the Thor VM3 is field replaceable. The front panel assembly contains the keypad, touch screen and optional defroster. Should any of these components fail, the front panel assembly can easily be replaced to reduce downtime. The replacement front panel is available in these configurations: •...
Page 140
#2 Phillips bit and torque the screws to 7 ± 0.5 inch pounds. 10. Reinstall the Thor VM3 in the dock. 11. When the Thor VM3 is placed in the powered dock, the UPS battery automatically reconnects.
After the system files are processed, Microsoft Windows begins to load. Windows main- tains a System Registry and INI files. Standard Windows configuration options apply to the Thor VM3. Configuration options are located in the System Tray or the Control Panel: •...
Page 142
For more information on Microsoft Windows device drivers, please refer to commercially available Windows OS reference guides. Radio Software The Thor VM3 is delivered with the radio software installed. Because the Thor VM3 uses a Microsoft Windows operating system, the radio installation includes Windows device drivers.
Page 143
CloneNGo To launch CloneNGo, right-click on the CloneNGo icon on the desktop and select Run as Administrator. For information on using CloneNGo on the Thor VM3, refer to the CloneNGo User Guide available at www.honeywellaidc.com. WLAN Wireless Configuration Utility (WCU) Manage the wireless 802.11 client installed in the Thor VM3.
Thor VM3. The Image line displays the revision of the system soft- ware installed. Refer to the last three digits to determine the revision level.
Page 145
The Network IP tab displays the MAC address of the network card(s) such as the WLAN radio and the Bluetooth module. First, locate the Thor VM3 Bluetooth address by tapping (Start) > Control Panel > Bluetooth > About tab. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
1. Turn on the printer. 2. Select Bluetooth Printing from the control panel. 3. Select Search and tap Acquire Printer. 4. A list of available Bluetooth printers is displayed. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 147
To continue after this error: • Dismiss the error. • Return to the Bluetooth Printing control panel and repeat the process starting with step 3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 148
7. The Bluetooth printer is shown. Print a test page if desired. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Some scanners are not supported via Bluetooth Scanning. To connect one of these scanners, see Adding Other Scanners. If a scanner does not connect, see Troubleshooting for help. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 150
Honeywell Granit 1911i Bluetooth scanner • Honeywell Granit 1981i Bluetooth scanner • LXE 88x0 family of Bluetooth scanners Use the bar code Quick Connect bar code on either side of the Thor VM3 to connect the following scanners: • Intermec SF51 Bluetooth scanner •...
Page 151
1. Select Bluetooth Scanning from the Control Panel (either large or small icon view option must be selected). 2. Tap Add Device. 3. Select Search. 4. Tap Next. 5. Select the scanner from the devices shown. 6. Tap Next. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Connect feature (depending on firmware installed). If Quick Connect does not work, use the other options to connect these scanners. • If the Honeywell Granit 1911i and Granit 1981i scanners cannot be found with the Search option, scan the PDAs/Mobility Systems Devices bar code from the scanner manual and search again.
External bar code scanners are supported by connecting the scanner to a COM port, USB port, or by Bluetooth. The scanners parameters, including bar code symbologies, can be configured using Enterprise Settings > Data Collection. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 154
BT-Configure on Connect Auto-configure on connect: • Overwrite with computer settings • Keep scanner settings Bluetooth Parameters • Power • On (default) • Disable (default) Discoverable • Enable Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 155
Enterprise Terminal Emulation Enterprise Terminal Emulation Configuration Options Printers Parameters Printer Options If connected through Bluetooth Printing, configuration options such as Auto detect printer, memory, display, etc. are available. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 156
Barcode Scanner Wedge • Label Encoding (Code Page) Bar Code Scanners and Enterprise Settings The following types of bar code scanners are supported on the Thor VM3: • A tethered scanner connected to COM1 or COM2 • A tethered scanner connected to a USB host port...
Page 157
For the Thor VM3 the USB Intermec SR61T and SR31 may be setup to be configurable through Enterprise Settings. This can be done by setting Enable USB Scanner Auto- detect to On under the Data collection menu.
Remap a Key to a Unicode Value 1. Select the modifier key from the Modifier Mode options. 2. The key to be remapped is the programmable function (PF) key on the numeric keyboard. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 159
If necessary, use the Clear button to erase all entries in the Key Sequence box. 8. Click OK to save the result and close the control panel. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 160
This clears the text box (though the command is saved). Enter the desired parameters in the appropriate text box. 7. Click OK to save the result and close the control panel. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 161
Some executables may require elevated privileges to run. For example, an executable such as regedit.exe may not run for a standard user but does run for an admin user. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
USB Powered in Sleep By default, power is removed from attached USB devices when the Thor VM3 is in Standby or Sleep mode. Check this box to maintain power to attached USB devices in...
Plugged in for when external power is present (such as vehicle power or from an AC power adapter) • Running on batteries for when external power is not present and the Thor VM3 is operating on UPS power. (Start) > Control Panel > Power Options > Power Schemes tab (Classic View) (Start) >Control Panel >...
Page 164
(Start) > Control Panel > Power Options (Large or Small Icon View) The Thor VM3 has four power management as described in the following sections. Select the AC/DC power plan when it is desired that the Thor VM3 power on when exter- nal power is connected.
Page 165
• Thor VM3 is already mounted to a dock and external power is applied to the dock • Thor VM3 is already mounted to a dock and the dock power switch is turned On Result The Thor VM3 boots. Once booted the Thor VM3 follows the AC/DC power plan with timers reset after the boot completes.
Page 166
Ignition switched to Active. An example of this case would be a Thor VM3 that is running on UPS and is then mounted on a dock that has truck power and the ignition switch is already On.
Page 167
Ignition Control/Ignition Off Behavior When either Ignition Control power plan is selected and external power is present the Thor VM3 behaves as described below. If external power is not present, refer to the section for Thor VM3 behavior. Thor VM3 is Off and Vehicle Ignition is Off Conditions The Thor VM3 is Off and vehicle ignition is Off.
Page 168
Ignition switched to Inactive. UPS charging is disabled. An example of this case would be a Thor VM3 that is running on UPS and is then mounted on a dock that has truck power and the ignition switch is already Off.
Page 169
Select the Auto-On power plan when it is desired that the Thor VM3 power on when external power is connected. In Auto-On mode, the Thor VM3 is turned On by the presence of external power with no user interaction required. Ignition input is ignored when Auto-On Mode is enabled.
Page 170
Result The Thor VM3 continues to run and follows Auto-On power plan with timers reset at the time power was connected. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 171
The Thor VM3 behavior when operating from UPS power is described below. Thor VM3 is Off Conditions The Thor VM3 is Off and the power button is pressed the Thor VM3 and the following condition is met: • UPS power is over 35% capacity...
Page 172
Configure Hibernation (Start) > Control Panel > Power Options (Large or Small Icon View) By default, hibernate is enabled on the Thor VM3. To change the hibernate settings: Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 173
Enter 0 to disable hibernation for the specified plan and power source (battery or external). 7. Tap OK and close all open power control panels. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Programmable Key (Start) > Control Panel > Programmable Key (Classic view) This function remaps P1-P7 keys integrated into the front panel of the Thor VM3. To remap the programmable keys (PF and Yellow + PF) in the optional external (21-key...
Page 175
Unicode value in the text box to the right of ALT + and the Unicode character is displayed in the box to the right of =. 5. Click OK to save the result and close the control panel. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 176
Toggle SIP (soft keyboard) state between displayed and hidden • Toggle touch screen state between enabled and disabled • Toggle integrated keyboard backlight state between on and off Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 177
The default for all text boxes is Null or “ ”. The text boxes accept string values only. The executables and parameters are not checked for accuracy by the keyboard driver. If the launch fails, the Thor VM3 displays a popup error message. If the launch is success- ful, no notification is displayed.
Page 178
The executables and parameters are not checked for accuracy by the keyboard driver. If the launch fails, the Thor VM3 displays a popup error message. If the launch is success- ful, no notification is displayed. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 179
Some executables may require elevated privileges to run. For example, an executable such as regedit.exe may not run for a standard user but does run for an admin user. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The instructions for installing, changing and uninstalling languages in this section are applicable to Thor VM3 with Windows Embedded Standard 7 OS only. While similar con- trol panels are present on other operating systems, the instructions below are not valid for those systems.
Page 181
3. When prompted, tap Uninstall display languages. 4. Check the checkbox in front of the language name to uninstall and tap Next. English is the system language and cannot be removed. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Ambient Light %. Note: There is no default value for Ambient Light % as it varies depending on the level of light where the Thor VM3 is located. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 183
When the ambient light exceeds the threshold specified in Medium to high light level (%), the display backlight is automatically increased to a high level. • Likewise if the Thor VM3 is returned to a lower ambient light area, the display backlight automatically transitions to the appropriate lower display backlight level. Current Level Current levels of LCD brightness and ambient light are displayed as a percentage.
The VM3 audio is designed to be used with or without the side tone. This is acceptable permissible performance for the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
If there is more than one SSD installed, there is a tab for each drive. Tap the Settings button to set the frequency the automatically update data for the SSD drive(s). The default is 1 hour. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Note: The following applies to a Thor VM3 that is not part of a domain. When the Thor VM3 is part of a domain, the user is prompted for credentials at Windows startup or log on.
Page 187
Motion Detection Method Select the motion detection method. The Thor VM3 supports the screen blanking box to determine motion. Select the port (COM1 or COM2) to which the blanking box is attached. Note: By default, COM1 and COM2 ports are used by Enterprise Data Collection. To use a COM...
Configuration Storage Select the users to which the ZoomZome settings apply. • Global Storage - The ZoomZone settings apply to all users of the Thor VM3. • Per User Storage - The ZoomZone settings only apply to the current user.
Page 189
Test Zoom Area Tap the Test Zoom Area button. The zoom image is displayed. When finished, at the top of the display tap File > Exit to exit. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Tethered hand-held scanners are tethered to a serial port or a USB host port (via a dongle cable) on the Thor VM3 Smart Dock and are configured by scanning the engine-specific bar codes in the scanner manufacturer's programming guide. The manufacturer's guides are usually shipped with the bar code reader.
To view or edit the boot order, select the Boot tab. The boot drive an can also be selected at bootup. Press P5 from the Thor VM3 keypad or press F5 from an external keyboard. Use the arrows on the external keypad to make a selection.
6. Set PCI LAN first in the boot priority list. Note: Rather than change the boot order in the BIOS, press F5 as the Thor VM3 boots and use the menu presented to select PCI LAN as the boot device. After this boot up, the Thor VM3 returns to the default boot device shown in the BIOS.
Page 193
6. Set PCI LAN first in the boot priority list. Note: Rather than change the boot order in the BIOS, press F5 as the Thor VM3 boots and use the menu presented to select PCI LAN as the boot device. After this boot up, the Thor VM3 returns to the default boot device shown in the BIOS.
2. Insert the recovery DVD into the DVD drive. 3. Reboot the Thor VM3. 4. Repeatedly press the P5 key on the Thor VM3 front panel or the F5 key on the external keyboard. 5. When the Boot Menu is displayed, use the arrow keys on the external keyboard to select the USB DVD drive.
This utility provides an automated process to read the configuration settings from one Thor VM3 and then apply those settings to one or more other Thor VM3s with the same operating system. The Configuration Cloning Utility (CCU) is installed as part of the fac- tory software load.
- These files contain the factory default values for the software. These files are placed on the Thor VM3 when the applicable software was installed or upgraded. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 197
CCU . ccf files are encrypted for security. Once a ccf file is created on one Thor VM3 it can be copied to other Thor VM3s to duplicate the configuration. An existing ccf file can be opened, modified, applied to the Thor VM3, saved, saved with a different name, etc.
Page 198
Advanced user only. Basic user cannot view the expanded tree or modify settings. When settings have been loaded (either from Registry > Import Settings or File > Open) the following screen is displayed. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 199
Thor VM3. If the parameter setting changes should also be applied to this Thor VM3, select Regis- try > Import Settings. After importing the settings, a reboot is necessary for the changes to take effect on the Thor VM3.
Page 200
4. Select File > Save then specify a file name and tap Save to save the settings to a ccf file. 5. The ccf file can be used to configure another Thor VM3. See Example 4. Example 2: Modify settings on the current device and save to a file To modify the settings on the Thor VM3 running the CCU: 1.
If ran with no parameters, the GUI CCU interface is opened. Example 2: Import settings CCU.exe -import -[programs] -C:\myfile.ccf Us this command line example to import the current settings from the Thor VM3 run- ning the CCU. Where: import directs the CCU to read the settings from the system registry.
Page 202
Any prior changes made to these settings on the Thor VM3 are lost. If -reset is not specified, only the changed val- ues in the ccf file are applied. Any other setting previously made on the Thor VM3 are retained.
Thor VM3 after changing the IP address type. Important Notes It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
If the credentials are not entered then, the credentials window may be hidden by other windows. This screen contains several items: • Tasks • Status • Profile List Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 205
The radio has initiated a connection and is attempting to associate with the access point: • The SSID of the network is displayed below the access point icon. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 206
• Disconnect - If the selected profile is connected, this option disconnects the profile. • Rename - Use to assign a new name to the selected profile. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 207
5. Tap Reset to save the new password or Cancel to exit without changing the password. Browse Nearby Wireless Networks Tap the Browse nearby wireless networks to open the open this window. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
If logged on as admin, tap on any network in the list to create a profile for that network. Creating a Profile To create from the Profile list: 1. Log in as admin. 2. Tap the New button. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
6. Tap OK to exit and save the profile or type Cancel to exit without creating a profile. Advanced Profile Configuration Connection This tab shows the basic information used to create the profile. Options include: Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 210
Connect even if the network is not broadcasting its name (SSID) - If a network is not broadcasting its SSID, check this box. • Enable Atheros connection settings. Note: Atheros connection settings must be enabled to use CCX. It is disabled by default. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 211
Continue to the applicable section to configure the WCU for network security: • Open (No Security) • • WPA2-Personal • PEAP-TLS • LEAP • EAP-FAST PEAP • EAP-FAST TLS • EAP-TLS • EAP-TTLS • PEAP-MSCHAPv2 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 212
2. Set Encryption type to none. 3. Tap OK. 4. From the profile listing, make sure the desired profile is active. 5. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 213
3. Enter the Network Security Key. 4. Select the Key Index. 5. Tap OK. 6. From the profile listing, make sure the desired profile is active. 7. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 214
3. Enter the Network Security Key. 4. Tap OK. 5. From the profile listing, make sure the desired profile is active. 6. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 215
To configure for Microsoft PEAP-TLS: 1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to Microsoft Protected EAP (PEAP). Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 216
5. Set the authentication method to Smart Card or other certificate. 6. Tap the Configure button. 7. Select Use a certificate on this computer. 8. Select the trusted root certificate from the listed certificates. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 217
9. Tap OK to close any open windows. 10. From the profile listing, make sure the desired profile is active. 11. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 218
5. If saved username and password is selected, enter the credentials now. 6. Tap OK to close all open windows. 7. From the profile listing, make sure the desired profile is active. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 219
Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 9. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 220
To configure for Cisco EAP-FAST PEAP: 1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to Cisco:EAP-FAST. 4. Tap the Settings button. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 221
7. If saved username and password is selected, enter the credentials now. 8. From the profile listing, make sure the desired profile is active. 9. Tap the Authentication tab. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 222
Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 15. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 223
To configure for Cisco EAP-FAST TLS: 1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to Cisco:EAP-FAST. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 224
6. Select Use certificate on this computer. 7. No entries are needed on the Authentication tab. 8. The About tab provides Cisco copyright information. 9. Tap OK to close all open windows. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 225
10. From the profile listing, make sure the desired profile is active. 11. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 226
To configure for EAP-TLS: 1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to Microsoft Smart Card or other certificate. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 227
6. Select the trusted root certificate from the listed certificates. 7. Tap OK to close any open windows. 8. From the profile listing, make sure the desired profile is active. 9. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 228
1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to IGX: EAP_TTLS. 4. Tap the Settings button. 5. Select the Connection tab. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 229
Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 14. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 230
1. Set Security type to WPA2-Enterprise or CCKM. 2. Set Encryption type to AES. 3. Set network authentication method to PEAP-MSCHAPv2. 4. Tap the Settings button. 5. Select the Connection tab. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 231
Note: If the credentials are not entered when to window first pops up, the credentials window can become hidden behind other windows. 14. Verify the connection using Status. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Roam Management General The general tab provides information on the current connection. There are no user entries on this screen. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 233
Use CCX (Cisco Client Extensions) for faster roaming. Default is enabled. CCKM Use CCKM (Cisco Centralized Key Management) for faster roaming. Default is enabled. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 234
(MCS0 to MCS15). MCS0 (Modulation and Coding Scheme) 0 is slowest, MCS15 is fastest but subject to more errors. Default is disabled. Diversity By default, diversity is on. Selection Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 235
Adapter The adapter tab provides information on the radio card. There are no user entries on this screen. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
WCU either immediately before or immediately after the user logs into the computer. The delay can be configured from 1 to 120 seconds (10 seconds is the default). Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 237
After the client authenticates with one access point, it can roam to others under the same controller by handshaking rather than authentication. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Note: Please refer to the Security Primer to prepare the Authentication Server and Access Point for communication. Note: It is important that all dates are correct on the Thor VM3 and host computers when using any type of certificate. Certificates are date sensitive and if the date is not correct authentication will fail.
Certificates are date sensitive and if the date is not correct authentication will fail. The easiest way to get the root CA certificate is to use a browser on a PC or the Thor VM3 to navigate to the Certificate Authority. To request the root CA certificate, open a browser to http://<CA IP address>/certsrv.
Page 240
Click the Save button and save the certificate. Make sure to keep track of the name and location of the certificate. Next install the certificate on the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Install a Root CA Certificate Copy the certificate file to the Thor VM3. The certificate file has a .CER extension. Locate the file and double-tap on it. If presented with a security warning, confirm that you want to open the file.
Generate a User Certificate The easiest way to get the user certificate is to use the browser on the Thor VM3 or a PC to navigate to the Certificate Authority. To request the user certificate, open a browser to http://<CA IP address>/certsrv.
Page 243
Install the user certificate on the requesting computer by clicking the Install this certifi- cate link. If the requesting computer is the Thor VM3, then the process is finished. Otherwise, export the certificate as described below. Exporting a User Certificate Select Tools >...
The certificate is saved with a .PFX extension. Click Finish and OK to close the Successful Export message. Locate the User Certificate in the specified location. Copy to the Thor VM3. Install the User certificate. Install a User Certificate After generating and exporting the user certificate, install the user certificate.
Page 245
*.cer to *.pfx. After selecting the .PFX file, tap Open. 5. The certificate filename and path are displayed. Tap Next. 6. Return to the installation instructions above. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Connection troubleshooting: • If there is a connection issue, the first step in troubleshooting is to verify the APN on Connection Type tab. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
The active connection displays the IP address and signal strength (RSSI). Inactive con- nections show the status as Standby. If a WWAN connection is active, the roaming status (Home or Roam) is displayed. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
(WCU). The WWAN networks, if any, are shown on this page. A WWAN network is only displayed if a SIM card has been installed for that network. The Thor VM3 supports two SIM cards. Install SIM Card(s) for SIM card installation instructions. A WWAN network can be enabled or disabled from this screen, however the connection is configured by tapping the applicable Network Settings button.
Page 249
To configure a WWAN network, tap the View Network Settings button. To configure the WLAN connection use the WLAN Wireless Configuration Utility (WCU). Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 250
Authentication. If these items are not present, contact Customer Support software upgrade options. If using a public APN, the software upgrade is usually not necessary. After all entries are completed, tap the Save button. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 251
Next select the PIN/PUK tab. Note that the SIM card being configured (Sim1 or Sim2) is identified at the top of this tab. Enter the PIN or PUK and tap Save then tap Exit to return to the Connection Manager. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Connected Not connected This icon is in addition to the connection icon in the system tray. By default the on-screen icon is disabled. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 253
Honeywell recommends distributing firmware via a WLAN connection rather than the WWAN connection. This requires an HTTP server which can be hosted on the Internet or the same Intranet (i.e.: the same network domain) as the Thor VM3. Honeywell tested FOTA using: •...
Page 254
5. Click on the Apache tab and select Access and Passwords > Folder www access and passwords. 6. Select Password Disabled and Local, Intranet and Internet Access. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 255
• Ping the sever from the Thor VM3 to verify connectivity between the devices. • Open the web browser on the Thor VM3 and verify the URL of the server can be accessed. Load Firmware Updates The firmware update is provided by Honeywell customer support. The update consists of a version string and a zip file.
Page 256
For example, if the web server is hosted at http://127.0.0.1, the path is entered as http://127.0.0.1/wwan/ Important - the trailing / must be included after wwan. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Tap the Start button to begin receiving GPS data. Once started, the button label changes to Stop and GPS data on screen is populated. Tap the Clear GPS Data button to erase the GPS data. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
About The about screen has no user-configurable parameters. It identifies the firmware and hardware versions, the carrier selected, MEID, etc. for the WWAN radio. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
CHAPTER KEY MAPS Integrated Keypad There are seven integrated programmable keys located on the Thor VM3 below the dis- play. Each programmable key can be modified by the Orange key for a total of 14 pro- grammable keys. Programmable Key to remap these keys.
Page 260
Increase speaker volume Blue Decrease speaker volume Blue Increase display brightness Blue Decrease display brightness Blue The Blue plus P3, P4 or P7 key press sequences cause no action. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Pressing the backlight key (alone or after the Green or Yellow keys) cycles the keypad backlight through Low, Medium, High, Off then repeats. Yellow- Green- Non-Shifted Shifted Shifted Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 262
Yellow- Green- Non-Shifted Shifted Shifted Programmable Programmable Delete Backspace Backtab Left Left Left Left Right Right Right Right Down Down Down Down Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
95-key PS/2 Keyboard. The key map table that follows lists the commands used for the Thor VM3. Note that since the Thor VM3 uses a Microsoft Windows operating system, no DOS Terminal Emulation keypress sequences are provided. There are 10 hidden keys on the 95 key keyboard. Each of the hidden keys is accessed by pressing the <Fn>...
The 2nd functions of the F4 and F5 keys are not used as the display brightness is adjusted via the buttons on the front of the Thor VM3. • The 2nd functions of the F6 and F7 keys are not used as the Thor VM3 has TFT LCD screen with no provision for contrast adjustments. •...
Page 265
Right Arrow Left Arrow Left Arrow Insert Bksp Delete (numeric) Home Left Arrow Right Arrow Page Up Up Arrow Page Down Down Arrow ScrollLock Shift Shift Shift Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 266
To get this Key / Press These Keys in this Order Function Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Shift Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 267
/ (alpha) - (numeric) Ctrl - (alpha) + (numeric) Ctrl + (alpha) * (numeric) I (letter i) * (alpha) Ctrl I (letter i) : (colon) ; (semicolon) Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 268
To get this Key / Press These Keys in this Order Function _ (underscore) , (comma) ' (apostrophe) ~ (tilde) " & Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Power Supply 10 to 60 VDC isolated Uninterruptible Power Supply Internal UPS battery, 30-minute life at -30°C (-22°F) Backup Battery (RCT) Internal lithium battery maintains Real Time Clock Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
External Power Supply 50-150 VDC DC power supply available for vehicles over 60 VDC Note: Use dock VMX005VMCRADLE (VMXD Enhanced Dock of Off-Vehicle Use) in AC power applications. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
9-pin female, USB connector supports USB host port via adapter cable Note: USB Client port may not be supported by the Thor VM3 operating system. USB 2 Connector 15-pin female, USB connector supports 2 USB host ports via adapter cable...
Note: The RAM ball is not included in the following measurements. Length 7.1” (18.0 cm) Width 6.1” (15.5 cm) Height 2.1” (5.4 cm), measurement includes strain relief cable clamps Weight 2.4 lb. (1.1 kg) Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Operating Humidity Up to 95% Water and Dust IEC 60529 compliant to IP66 15 kV air, 8kV direct contact Vibration MIL-STD-810F, composite wheeled vehicles. Crash SAE-J 1455 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
2.402 - 2.480 GHz QDID B013455 WWAN Device Software definable (data only), includes GPS Technology 4G radio: LTE/UMTS/HSPA+/GSM/GPRS/EDGE/ EV-DO Supports 2 SIM cards for hyper-roaming between WWAN carriers Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Screen Blanking Box - The white wire in the power cable must be connected to the unswitched side of the screen blanking box. See applicable wiring diagram below. Cable shell provides chassis ground connection. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 278
VMXD enhanced dock for off-vehicle use requires adapter cable VM1076CABLE to con- nect the dock to the AC/DC adapter. This cable is included in the AC kit for off-vehicle use. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
PIN 9 PIN 6 Common ground Common ground USB_H1_D+ USB host 1 data signal USB_H1_D- USB host 1 data signal USBC_VBUS USB client 5V detect from attached host Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 280
USB D- PIN 1 USB_H1_D+ USB D+ USB Power Return Shell CGND Chassis Ground USB Client Connector The USB client connection is not supported on the Thor VM3. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Common ground Common ground USB_H3_PWR USB host 3 5V output power USB_H3_D+ USB host 3 data signal USB_H3_D- USB host 3 data signal Common ground Common ground Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 282
USB Host Connectors Signal Description 5V_USB USB Power, Current Limited PIN 4 USB_H2_D- USB D- PIN 1 USB_H2_D+ USB D+ USB Power Return Shell CGND Chassis Ground Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 283
PS/2 to USB Keyboard Adapter Cable Note: This cable is not supported when the Thor VM3 is used with the VM1D Standard Dock. D9 Male Connector - USB Signal Description Not Used PIN 5 PIN 1 Not Used Not Used...
Mic input Microphone input Mic return Microphone return Audio Return Optional ground CAN_SHLD CAN_H CAN_H bus line dominant high CAN reserved CAN_V+ Option CAN external Power Supply Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 285
Not used Quick Connect Headset Connector Signal Description Mic input Microphone input PIN 4 Mic return Microphone return Audio output Headset output PIN 1 Audio return Headset return Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 286
CAN_V+ Option CAN external Power Supply CAN_H CAN_H bus line dominant high CAN_L CAN_L bus line dominant low CAN_SHLD Not used Not used Not used Not used Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Licenses of Third Party Software This product contains software provided by third parties, which may include the below listed components. The Honeywell product that includes this file does not necessarily use all of the third party software components referred to below.
Page 290
To "modify" a work means to copy from or adapt all or part of the work in a fashion requiring copyright permission, other than the making of an Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 291
The "Corresponding Source" for a work in object code form means all the source code needed to generate, install, and (for an executable work) run the object code and to modify the work, including scripts to Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 292
11 of the WIPO copyright treaty adopted on 20 December 1996, or similar laws prohibiting or restricting circumvention of such measures. When you convey a covered work, you waive any legal power to forbid Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 293
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 294
Convey the object code using peer-to-peer transmission, provided you inform other peers where the object code and Corresponding Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 295
(and with an implementation available to the public in source code form), and must require no special password or key for Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 296
10. If the Program as you received it, or any part of it, contains a notice stating that it is governed by this License along with a term that is a further Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 297
However, nothing other than this License grants you permission to propagate or modify any covered work. These actions infringe copyright if you do Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 298
In the following three paragraphs, a "patent license" is any express agreement or commitment, however denominated, not to enforce a patent Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 299
If conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot convey a Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 300
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 301
This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 302
General Public License, and the "GNU GPL" refers to version 3 of the GNU General Public License. "The Library" refers to a covered work governed by this License, Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 303
(ten or fewer lines in length), you do both of the following: Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 304
Combined Work produced by recombining or relinking the Application with a modified version of the Linked Version. (If Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 305
Library. Package(s) using Boost regex library License ============================ * The Boost C++ Libraries Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 306
Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users. This license, the Lesser General Public License, applies to some Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 307
General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 308
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 309
The modified work must itself be a software library. b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 310
Do not make any other change in these notices. Once this change is made in a given copy, it is irreversible for Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 311
Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 312
Library" must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 313
You may not impose any further restrictions on the recipients' exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 314
License which applies to it and "any later version", you have the option of following the terms and conditions either of that version or of any later version published by Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 315
Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 316
LICENSE ISSUES ============== The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 317
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 318
* 4. If you include any Windows specific code (or a derivative thereof) from * the apps directory (application code) you must include an acknowledgement: * "This product includes software written by Tim Hudson (tjh@cryptsoft.com)" Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 319
1. The origin of this software must not be misrepresented; you must not claim that you wrote the original software. If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 320
Contributor, the initial code and documentation distributed under this Agreement, and b) in the case of each subsequent Contributor: i) changes to the Program, and Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 321
Contributors all liability for damages, including direct, indirect, special, incidental and consequential damages, such as lost profits; Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 322
IN ANY WAY OUT OF THE USE OR DISTRIBUTION OF THE PROGRAM OR THE EXERCISE OF ANY RIGHTS GRANTED HEREUNDER, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 323
* All rights reserved. Redistribution and use in source and binary * forms, with or without modification, are permitted provided that * this copyright notice is retained. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 324
The above copyright notice and this permission notice shall be included in all copies or substantial portions of the Software. THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 325
* Neither the name of ekus.net nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 326
"Work" refers to the collection of files distributed by the Publisher, including the Source Code, Executable Files, binaries, data files, documentation, whitepapers and the Articles. "You" is you, an individual or entity wishing to use the Work and exercise your rights under this License. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 327
PUNITIVE OR EXEMPLARY DAMAGES ARISING OUT OF THIS LICENSE OR THE USE OF THE WORK OR OTHERWISE, EVEN IF THE AUTHOR OR THE PUBLISHER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Termination. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 328
If you use this software in a product, an acknowledgment in the product documentation would be appreciated but is not required. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 329
“NOTICE SPECIFIC TO SOFTWARE AVAILABLE ON THIS WEB SITE.” If you use such code (the “software”), you accept this license. If you do not accept the license, do not use the software. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 330
License Text (blowfish License) -------------------------- // blowfish.cpp C++ class implementation of the BLOWFISH encryption algorithm // _THE BLOWFISH ENCRYPTION ALGORITHM_ // by Bruce Schneier // Revised code--3/20/94 Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 331
(a) that the initial Contributor has attached the notice described in Exhibit B to the Covered Software; or (b) that the Covered Software was made available under the terms of Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 332
You. For purposes of this definition, "control" means (a) the power, direct or indirect, to cause the direction or management of such entity, Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 333
This License does not grant any rights in the trademarks, service marks, or logos of any Contributor (except as may be necessary to comply with the notice requirements in Section 3.4). Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 334
License, or sublicense it under different terms, provided that the license for the Executable Form does not attempt to limit or alter the recipients' rights in the Source Code Form under this License. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 335
Software under this License. Except to the extent prohibited by statute or regulation, such description must be sufficiently detailed for a recipient of ordinary skill to be able to understand it. 5. Termination -------------- Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 336
* authorized under this License except under this disclaimer. ************************************************************************ ************************************************************************ * 7. Limitation of Liability * -------------------------- * Under no circumstances and under no legal theory, whether tort Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 337
10.2. Effect of New Versions You may distribute the Covered Software under the terms of the version of the License under which You originally received the Covered Software, Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Page 338
Exhibit B - "Incompatible With Secondary Licenses" Notice --------------------------------------------------------- This Source Code Form is "Incompatible With Secondary Licenses", as defined by the Mozilla Public License, v. 2.0. Thor VM3 with Microsoft Windows 7 or Windows Embedded Standard 7 User Guide...
Label Locations Compliance labels are located in the dock well area on the back of the Thor VM3, as indicated by the shaded areas below. The Thor VM3 must be removed from the dock to view the labels.
Page 340
Honeywell 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com ™ VM3-W7-UG Rev F 9/17...