hit counter script
Epson DM-D110 Technical Reference Manual
  1. Manuals
  2. Brands
  3. Epson Manuals
  4. Monitor
  5. DM-D110 Series
  6. Technical reference manual
Epson DM-D110 Technical Reference Manual

Epson DM-D110 Technical Reference Manual

Hide thumbs Also See for DM-D110:
Table of Contents

Advertisement

Quick Links

Download this manual
Technical Reference Guide
Product Overview
Describes features and general specifications for this
product.
Setup
Describes how to install and set this product.
Handling
Describes the basic usage of this product.
Application Development Information
Describes how to control this product and information
necessary for developing applications.
Appendix
Describes the specifications of the product, connectors,
and serial cables, as well as the character code table.
M00035605
Rev. F

Advertisement

Table of Contents
loading

Related Manuals for Epson DM-D110

Summary of Contents for Epson DM-D110

  • Page 1 Technical Reference Guide Product Overview Describes features and general specifications for this product. Setup Describes how to install and set this product. Handling Describes the basic usage of this product. Application Development Information Describes how to control this product and information necessary for developing applications.
  • Page 2 • Neither is any liability assumed for damages resulting from the use of the information contained herein. • Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third par- ties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance...

  • Page 3: For Safety

    For Safety Key to Symbols The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. You must follow warnings carefully to avoid serious bodily injury. WARNING Provides information that must be observed to prevent damage to the equipment or loss of data. •...

  • Page 4: Warnings

    Warnings • To avoid risk of electric shock, do not set up this product or handle cables during a thun- derstorm. • Never insert or disconnect the power plug with wet hands. WARNING Doing so may result in severe shock. •...

  • Page 5: Restriction Of Use

    Aim of the Manual This manual provides the development engineers with necessary information for developing, designing, install- ing the system using DM-D110/DM-D210 as well as for developing and designing the applications. Manual Content The manual is made up of the following sections:...

  • Page 6: Table Of Contents

    Customer Display ................................10 Accessories ..................................10 Options ....................................11 ■ Part Names ..........................12 DM-D110 .....................................12 DP-110....................................12 DM-D110 for TM-T88V-DT/TM-T88VI-DT2 .......................13 DM-D210 .....................................14 DP-210....................................14 ■ System Outline ........................15 USB (Self Powered) ................................15 USB (Bus Powered): Computer ............................15 USB (Bus Powered): TM Intelligent Printer ......................16 Serial (Stand-Alone).................................17...
  • Page 7 DP-502 (TM-H6000IV/TM-U675) ..........................44 DP-502 (TM-H6000IV-DT)..............................50 DP-502 (TM-U950) ................................56 DP-502 (TM-J7200 / TM-J7700) ...........................59 DP-502 (Attaching on the counter) ...........................63 DP-503 (TM-H5000II)...............................66 DM-D110 for TM-T88V-DT/TM-T88VI-DT2 .......................68 ■ Connecting..........................74 USB (Self Powered) ................................74 USB (Bus Powered)................................75 Serial (Stand-Alone).................................76 Serial (Pass-through) ...............................77 Serial (Y-type) ..................................78...
  • Page 8 ■ Precautions when Using the USB Models ............... 91 ■ Precautions when using the serial (USB controlled) ............. 91 Appendix......................92 ■ Product Specifications ......................92 DM-D110 .....................................92 DM-D210 .....................................97 Environmental Conditions............................99 ■ DP-110/DP-210 Connector Specifications..............100 ■ Serial Cable Specifications ....................106...

  • Page 9: Product Overview

    Product Overview This chapter describes features and specifications of the DM-D110/DM-D210. Features DM-D110/DM-D210 is a customer display for displaying characters. The main features of this product are as follows. Display • 20 digit x 2 lines dot matrix for displaying half-width characters.

  • Page 10: Product Structure

    Product Structure Customer Display The following shows the models for the customer display unit. DM-D110 • RS-232/USB model • RS-232 model • USB model • DM-D110 for TM-T88V-DT/TM-T88VI-DT2 model (For TM-T88V-DT/TM-T88VI-DT2) DM-D210 • RS-232/USB model • RS-232 model Accessories Model Accessory •...

  • Page 11: Options

    Installation set for the TM-H5000II and J8000 series PS-180 AC adapter DM-D110 DP-110 DM-D110 stand (with an interface board) DP-110 without Interface Board DM-D110 stand (without an interface board) Use this when installing near the USB bus power and the printer using a Y-type connection.

  • Page 12: Part Names

    Chapter 1 Product Overview Part Names DM-D110 Dip switch (rear side) Screen Power Switch (bottom side of the display) USB cable *1 *2 Ferrite core (with a cap RS-232 cable (with a cap ∗1 For the USB model, the power switch, ferrite core, USB cable cap and RS-232 cable are not included.

  • Page 13: Dm-D110 For Tm-T88V-Dt/Tm-T88Vi-Dt2

    Chapter 1 Product Overview DM-D110 for TM-T88V-DT/TM-T88VI-DT2 Ferrite core Dip switch (rear side) Straight pole Screen Base USB cable (with a cap L-shaped pole ∗ They may not be supplied for DM-D110 for TM-T88V-DT/TM-T88VI-DT2 depending on when the product is shipped.

  • Page 14: Dm-D210

    Chapter 1 Product Overview DM-D210 Screen Power Switch (bottom side of the display) Dip switch (bottom side of the display) USB cable (with a cap) Ferrite core RS-232 cable (with a cap ∗ For the RS-232 model, the USB cable, RS-232 cable cap and ferrite core are not included. DP-210 DM-D connector Power supply connector...

  • Page 15: System Outline

    Connect to a USB bus that has sufficient power supply capability. Otherwise brightness may decline. Be careful when connecting to a laptop computer or a USB hub. DM-D110: You can use the RS-232/USB and USB models. DM-D210: You cannot use it.

  • Page 16: Usb (Bus Powered): Tm Intelligent Printer

    Connect this product’s USB cable to the TM intelligent printer. Power is supplied from the TM intelligent printer. TM-T88V-DT/TM-T88VI-DT2 (Attach DM-D110 for TM-T88V-DT/TM-T88VI-DT2) TM-T88V-DT/TM-T88VI-DT2 DM-D110 for TM-T88V-DT/TM-T88VI-DT2 TM-DT series/TM-i series TM Intelligent Printer DM-D110 DM-D110: You can use the RS-232/USB and USB models. DM-D210: You cannot use it.

  • Page 17: Serial (Stand-Alone)

    Chapter 1 Product Overview Serial (Stand-Alone) Connect DP-110/DP-210 to the computer using a serial cable. Computer DM-D110/DM-D210 Serial PS-180 Serial (Pass-through) Connect the serial interface TM printer to the DP-110/DP-210 connected to the computer using a serial connection. The power to the TM printer is supplied from DP-110/DP-210 via a power extension cable.

  • Page 18: Serial (Y-Type)

    Serial (Y-type) Connect this product’s RS-232 cable to the TM printer DM-D connector, and then connect the TM printer and the computer using a serial cable. Power is supplied from the TM printer. TM Printer DM-D110/DM-D210 Computer PS-180/PS-190 Serial RS-232...

  • Page 19: Serial (Usb Controlled)

    PS-180 UB-U02III RS-232 DM-D110/DM-D210 Serial (USB/Ethernet controlled) Connect this product's RS-232 cable to the DM-D connector of the TM printer, and then connect the TM printer and computer by using a USB cable or via the network. Power is supplied from the TM printer.

  • Page 20: Connection Patterns By Options

    Chapter 1 Product Overview Connection patterns by options The following table shows the connection pattern you can use for each option. DP-110, DP-210, DP-502 and DP-503 are not supported by TM-H6000VI. DM-D110 (except DM-D110 for TM-T88V-DT/TM-T88VI-DT2) Option DP-110 Connection Pattern...

  • Page 21: Setup

    (page Connecting Cables (page Installing the DM-D110 Virtual COM Port Driver to the Computer For details, see the manual supplied with the DM-D110 Virtual COM Port Driver. ∗ When extending the length of the support, prepare the option of DP-105.

  • Page 22: Usb (Bus Powered): Computer

    For details, see the manual supplied with the DM-D110 Virtual COM Port Driver. For the TM-i series host, you do not need the DM-D110 Virtual COM Port Driver. For the TM-DT series host, the DM-D110 Virtual COM Port Driver is already installed.

  • Page 23: Serial (Stand-Alone)

    Chapter 2 Setup Serial (Stand-Alone) Preparation • Option (DP-110 /DP-210) • AC adapter • Power cord • Serial cable (page 106) Dip Switch Settings (page Attaching the Product (page Connecting Cables (page ∗ When extending the length of the support, prepare the option of DP-105. Serial (Pass-through) Preparation •...

  • Page 24: Serial (Y-Type)

    Chapter 2 Setup Serial (Y-type) Preparation • DM-D110: Select from the following options • DP-110 • DP-502 • DP-503 • DM-D210: Select from the following options • DP-210 • DP-502 • DP-503 • TM Printer (with DM-D connector, Serial interface) •...

  • Page 25: Serial (Usb Controlled)

    Chapter 2 Setup Serial (USB controlled) Preparation • DM-D110: Select from the following options • DP-110 • DP-502 • DP-503 • DM-D210: Select from the following options • DP-210 • DP-502 • DP-503 • TM Printer (with UB-U01III or UB-U02III) •...

  • Page 26: Serial (Usb/Ethernet Controlled)

    Chapter 2 Setup Serial (USB/Ethernet controlled) Preparation • DM-D110 • DP-502 • DM-D210 • DP-502 • TM Printer • AC adapter • Power cord Dip Switch Settings (page Set the communication speed to 19200 bps. Attaching the Product (page * DP-502 is not supported by TM-H6000VI. Refer to the next step (Connecting Cables).

  • Page 27: Dip Switch Settings

    Serial (USB/Ethernet controlled) Set the communication speed to 19200 bps. TM Intelligent Printer (ePOS-Device) Match the serial communication settings for the TM intelligent printer’s EPSON TMNet WebConfig and this product. TM-DT Series (Windows) Match the serial communication settings for the TM-DT Series and this product.

  • Page 28: Setting Method

    Do not remove the DIP switch cover until after turning the power off. Removing the cover while the power is turned on may damage the device. Turn off the power of this product and system, and remove cable. Remove the DIP switch cover. DM-D110 DM-D210 7 8 9 10 9 10...

  • Page 29: Dip Switch 1 Functions

    Chapter 2 Setup DIP Switch 1 Functions The following explains the DIP switch functions. DSW1 No. Function Default Setting Received Error Data Ignore Ignore "?" Display Receive Data Length 7 bit 8 bit Parity With Parity No Parity Parity Selection Even Communication Speed Refer to...

  • Page 30: Attaching The Product

    Use the optional DP-502 to attach DM-D110 to TM-H6000IV-DT. page 50 Use the optional DP-502 to attach DM-D110/DM-D210 to TM-U950. page 56 Use the optional DP-502 to attach DM-D110/DM-D210 to TM-J7200/ TM-J7700. page 59 Use the optional DP-502 to attach DM-D110/DM-D210 to the counter. page 63 DP-503 Use the optional DP-503 to attach DM-D110/DM-D210 to TM-H5000II.
  • Page 31 Chapter 2 Setup DP-110 Checking the accessories Check the DP-110 parts. Plate DP-110 Extension power cable RS-232C connector installation screw (millimeter type) Checking the accessories of DP-105 Check the DP-105 parts. Affixing tapes Extension support...
  • Page 32 Chapter 2 Setup Setting the DP-110 Connector installation screw Inch-type hexagonal lock screws are installed in the connector for serial cable connection of DP-110. If millimeter-type lock screws are needed, use the millimeter-type lock screws of the accessory. Notch (one or more lines) inch-type millimeter-type Installation screw...
  • Page 33 When extending the length of the DP110, attach the extension support (DP-105) to the DP-110. When using the extension support (DP-105) Insert the tab on the DM-D110 (or the extension support) into the hole on the DP-110 until you feel it click.
  • Page 34 Chapter 2 Setup Connect the cable to DP-110, computer, and TM printer to match the constructed environment. (See "Connecting" on page Arrange the cables as shown below. Put the cables inside the DP-110. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside DP-110.
  • Page 35 Chapter 2 Setup DP-210 Checking the accessories Check the DP-210 parts. DP-210 Support Extension support RS-232C connector installation screw Extension power cable (millimeter type) Setting the DP-210 Connector installation screw Inch-type hexagonal lock screws are installed in the connector for serial cable connection of DP-210. If millimeter-type lock screws are needed, use the millimeter-type lock screws of the accessory.
  • Page 36 Chapter 2 Setup Installing to the DP-210 Because the illustration used here is for the RS-232/USB model, there are 2 cables. The RS-232 model have 1 cable. Pass the cable for the DM-D210 through the support. When using the extension support, insert the tab on it into the hole on support until you feel it click.
  • Page 37 Chapter 2 Setup Connect the cable to DP-210, computer, and TM printer to match the constructed environment. (See "Connecting" on page Arrange the cables as shown below. Put the cables inside the DP-210. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside DP-110.

  • Page 38: Tm-H6000V)

    Chapter 2 Setup DP-502 (TM-H6000V) • Set DIP switch 2-2 on the printer to "ON". • Set "Selection of interface using the customer display" on the printer according to the inter- face that is used. Checking the accessories Check the DP-502 parts. When attaching to the TM-H6000V, use the following parts. Angle fixing Fixing plate B Stopper...
  • Page 39 Chapter 2 Setup Installing to the TM-H6000V The illustrations used here are for DM-D210, but you can still use them as your reference for DM-D110. Turn the printer over. Attach the rubber feet to the printer. Pass the cable for this product through support C, and attach support C to this product.
  • Page 40 Chapter 2 Setup Pass the RS-232 cable for this product through the hole on fixing plate A. Do not pass the USB cable through fixing plate A as it is later stored in support C. For USB Cable Hook the cable to the tab of fixing plate A and secure. Install the ferrite core to the RS-232 cable of the customer's display, remove the cap, and connect the cable to the printer's DM-D connector.
  • Page 41 Chapter 2 Setup Attach fixing plate B to the printer. Attach fixing plate A to the TM printer using the stopper. When you attach the stop- per, insert the projections on the stopper into the holes of fixing plate B. Fixing plate A can be attached on either side of the printer.
  • Page 42 Chapter 2 Setup The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw. The roll paper cover and receipt unit may not open if the position of the display is incorrect.
  • Page 43 Chapter 2 Setup Turn the printer over to the normal status. Place a cap on the USB cable to store in the pole. Store the rest of RS-232 cable in the pole, and then install the customer display to fixing plate A.

  • Page 44: Tm-H6000Iv/Tm-U675)

    Chapter 2 Setup DP-502 (TM-H6000IV/TM-U675) Checking the accessories Check the DP-502 parts. When attaching to the TM-H6000IV/TM-U675, use the following parts. Angle fixing screw Fixing plate B Stopper Fixing screw for stopper Rubber feet (small) Fixing screws for fixing plate B Fixing screws for rubber feet (small) Support B for extension...
  • Page 45 Chapter 2 Setup Installing to the TM-H6000IV/TM-U675 • The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210. • Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 46 Chapter 2 Setup Attach fixing plate B to the printer. Pass the cable for this product through the hole on fixing plate A, and fix the cable at the bottom as shown below. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside support.
  • Page 47 Chapter 2 Setup Attach fixing plate A to the TM printer using the stopper. When you attach the stop- per, insert the projections on the stopper into the holes of fixing plate B. Fixing plate A can be attached on either side of the printer. (The illustration below shows fixing plate A attached to the right side of the printer.)
  • Page 48 Chapter 2 Setup The horizontal rotation mechanism of fixing plate A can be adjusted. To secure the location of the display, set fixing plate A to either one of the following four positions and secure it with the angle fixing screw. The paper roll cover may not open if the position of the display is incorrect.
  • Page 49 Chapter 2 Setup Store any excess cable in the support and attach this product to fixing plate A. Connect the DC cable to the printer. To avoid disconnection, hook the cable on the tabs on fixing plate B, as shown below.

  • Page 50: Tm-H6000Iv-Dt)

    Chapter 2 Setup DP-502 (TM-H6000IV-DT) Checking the accessories Check the DP-502 parts. When attaching to the TM-H6000IV-DT, use the following parts. Fixing screw Angle fixing screw Fixing plate B Stopper for stopper Fixing screws for fixing plate B Support B for extension Fixing plate A Support C...
  • Page 51 Chapter 2 Setup Installing to the TM-H6000IV-DT Follow the instructions to install the DM-D110 (USB model) on the TM-H6000IV-DT using the exclusive DP- 502. Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 52 Chapter 2 Setup Use the 2 screws removed in Step 2 and the 2 included long screws. Be sure not to connect the cables before attaching the plate. Otherwise, the cables can be damaged. The illustration shows how to install this product on the right side of the TM- H6000IV-DT.
  • Page 53 Chapter 2 Setup Select the position where this product is to be installed from A, B, C, or D.
  • Page 54 Chapter 2 Setup Move the attached part in Step 4 so that screw holes indicated in the illustration are aligned with each other, according to the position you selected. Fix it with the included screw. Use the included support B for extension if the support C is not long enough.
  • Page 55 Chapter 2 Setup Put the USB cable through behind TM-H6000IV-DT as shown in the illustration. Install this product to the Fixing Plate A. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside support.

  • Page 56: Tm-U950)

    Chapter 2 Setup DP-502 (TM-U950) Checking the accessories Check the DP-502 parts. When attaching to the TM-U950, use the following parts. Fixing screws for Rubber feet (square) plastic position Fixing plate A Support B for extension Support C...
  • Page 57 Chapter 2 Setup Installing to the TM-U950 • The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210. • Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 58 Chapter 2 Setup Pass the cable for this product through the hole on fixing plate A and fix the cable at the bottom as shown below. Adjust the length of the cable and secure fixing plate A to the printer with screws. Store any excess cable in the support, and attach this product to fixing plate A.

  • Page 59: Tm-J7200 / Tm-J7700)

    Chapter 2 Setup DP-502 (TM-J7200 / TM-J7700) TM-J7200/TM-J7700 can be installed on either side of the product. Checking the accessories Check the DP-502 parts. When attaching to the TM-J7200 and TM-J7700, use the following parts. Fixing screws for Fixing plate A Support B for extension Support C plastic position...
  • Page 60 Chapter 2 Setup Installing to the TM-J7200/TM-J7700 • The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210. • Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 61 Chapter 2 Setup Turn the printer over. When installing the AC adapter to the base of TM-J7700, see the "TM-J7200/TM- J7700 Technical Reference Guide" for procedures and notes regarding installation. When installing a customer display to the AC adapter side, do not use the power source fixing plate and screws included with TM-J7700.
  • Page 62 Chapter 2 Setup Install the ferrite core to the RS-232 cable of the customer's display, remove the cap, and connect the cable to the printer's DM-D connector. Hook the cable to the tab of fixing plate A and secure. Turn the printer over to the normal status. Place a cap on the USB cable to store in the pole.

  • Page 63: Attaching On The Counter)

    Chapter 2 Setup DP-502 (Attaching on the counter) Checking the accessories Check the DP-502 parts. When attaching it on the counter, use the following parts. [DP-502 parts] Affixing tapes Fixing screws for Affixing tapes wood position Fixing plate A Support B for extension Support C...
  • Page 64 Chapter 2 Setup Attaching on the counter • The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210. • Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 65 Chapter 2 Setup Pass the cable for this product through the hole on fixing plate A and fix the cable at the bottom as shown below. Peel off the affixing tapes and secure it to the mounting position. When using screws to attach it on the counter, use the screws to secure it to the mounting position.

  • Page 66: Tm-H5000Ii)

    Fixing screws Installing to the TM-H5000II • The illustrations used here are for DM-D110, but you can still use them as your reference for DM-D210. • Because the illustration used here is for the RS-232/USB model, there are 2 cables. The USB model and RS-232 model have 1 cable.
  • Page 67 Chapter 2 Setup Attach the base to the setting position on the TM printer and secure it with the screws. Pass the cable for this product through the base. Insert the tab on the base into the hole on the support until you feel it click. For the RS-232/USB model, the end of the connector of the unused cable should be capped, and then bundled to be stored inside support.

  • Page 68: Dm-D110 For Tm-T88V-Dt/Tm-T88Vi-Dt2

    Chapter 2 Setup DM-D110 for TM-T88V-DT/TM-T88VI-DT2 Checking the accessories Check the accessories of the DM-D110 for TM-T88V-DT/TM-T88VI-DT2. When attaching it on the printer, use the following parts. For models with a L-shaped pole Screws Base Customer display For models with a straight pole...
  • Page 69 Chapter 2 Setup Attaching to the DM-D110 for TM-T88V-DT/TM-T88VI-DT2 For models with a L-shaped pole Detach the connector cover of the TM printer. Detach the hooks from the TM printer while pushing the bottom parts on both sides of the connec- tor cover inwards.
  • Page 70 Chapter 2 Setup Pass the USB cable of the customer display through the base. Align the dowel hole in the customer display and the dowel on the base to attach the customer display on the base. Align the hook for the connector cover of TM printer with the groove on the back of TM printer, and then push it in.
  • Page 71 Chapter 2 Setup For models with a straight pole Detach the connector cover of the TM printer. Detach the hooks from the TM printer while pushing the bottom parts on both sides of the connec- tor cover inwards. Remove the U-shaped component from the connector cover. Attach the base on the TM printer with the three screws.
  • Page 72 Chapter 2 Setup With the end of the straight pole with a hole pointing downward, pass the USB cable of the customer display through the pole and base. Attach the pole with the customer display.
  • Page 73 Chapter 2 Setup Align the dowel hole in the pole and the dowel on the base to attach the pole on the base. Align the hook for the connector cover of TM printer with the groove on the back of TM printer, and then push it in.

  • Page 74: Connecting

    Connecting This section explains how to connect to the system by connection patterns. The illustrations used here are for DM-D110/DP-110, but you can still use them as your reference for DM- D210/DP-210. When attaching or removing the cables, make sure you turn off the power to the customer dis- play and the system.

  • Page 75: Usb (Bus Powered)

    Not used connector Computer interface connector Not used Printer interface connector Not used Not setting Not setting ∗1 Not available for the USB model. ∗2 They may not be supplied for DM-D110 for TM-T88V-DT/TM-T88VI-DT2 depending on when the product is shipped.

  • Page 76: Serial (Stand-Alone)

    • Remove the cap RS-232 cable • Attach the ferrite core • Connect to the DM-D connector of DP-110/DP-210 • DP-110 DM-D connector Connect the RS-232 cable of DM-D110/DM-D210 • DP-210 Power supply connector Connect the AC adapter Extension power cable Not used...

  • Page 77: Serial (Pass-Through)

    RS-232 cable • Attach the ferrite core • Connect to the DM-D connector of DP-110/DP-210 • DP-110 DM-D connector Connect the RS-232 cable of DM-D110/DM-D210 • DP-210 Power supply connector Connect the AC adapter Extension power cable Use the extension power cable and connect to the TM printer's...

  • Page 78: Serial (Y-Type)

    Not connected Serial cable AC adapter Computer DP-110/DP-210 Power cord TM Printer • DM-D110 • Do not remove the cap (factory default condition) USB cable • DM-D210 • Not used (bundle inside DP-110/DP-210 or DP-502/DP-503) • Remove the cap RS-232 cable •...

  • Page 79: Serial (Usb Controlled)

    Not connected USB cable AC adapter Computer DP-110/DP-210 Power cord TM Printer • DM-D110 • Do not remove the cap (factory default condition) USB cable • DM-D210 • Not used (bundle inside DP-110/DP-210 or DP-502/DP-503) • Remove the cap RS-232 cable •...

  • Page 80: Serial (Usb/Ethernet Controlled)

    RS-232 cable USB cable AC adapter Computer Ethernet Power cord TM Printer • DM-D110 • Do not remove the cap (factory default condition) USB cable • DM-D210 • Not used (bundle inside DP-502) • Remove the cap RS-232 cable • Attach the ferrite core •...

  • Page 81: Handling

    DM-D110 90° 48° DM-D110 for TM-T88V-DT/TM-T88VI-DT2 You can change the direction or angle of the display and L-shaped pole by moving them while holding TM printer by hand. With a L-shaped pole With a straight pole 270°...

  • Page 82: Cleaning The Customer Display

    Chapter 3 Handling Cleaning the customer display Turn off this product as well as the connected system. Use a dry cloth or firmly wrung cloth to wipe off any stains on this product. Do not use alcohol, benzine, thinner and other solvents; otherwise, the product may be damaged or the plastic parts may be broken.

  • Page 83: Application Development Information

    Refer to the Technical Reference Guide for each printer. ePOS-Device XML ePOS-Device XML is an Epson original control command system for POS printers and customer displays. It is defined in XML. An application creates a request message in XML format and sends it to printer using socket communications.

  • Page 84: Epos-Print Xml

    • TM-H6000VI (only for connecting serial interface) ESC/POS ESC/POS is the Epson original printer command system for POS printers and customer display. With ESC/POS commands, you can directly control all functions of this product, but detailed knowledge of printer specifica- tions or combination of commands is required, compared to using drivers and applications.

  • Page 85: Software And Manuals

    The following software and manuals are provided for application development. Development Kits Software Description Epson ePOS SDK Development kit for controlling the POS peripheral devices such as the printer and customer display from the Web application or native application for smart devices. for iOS It includes libraries, manuals, and sample programs.

  • Page 86: Drivers

    Chapter 4 Application Development Information Drivers Operating Software Description environment EPSON Advanced Printer Driver Windows printer driver that can display on the customer dis- Windows play. You cannot monitor the status. TM Virtual Port Driver Use when controlling ESC/POS commands using a serial (USB Windows controlled) connection.

  • Page 87: Data Flow Of Serial Commands

    Chapter 4 Application Development Information Data flow of serial commands This section explains the data flow when using this product using a serial connection. Block Diagram DM-D110/DM-D210 CPU for display unit Level shifter RS-232 cable connector Modular-8 DP-110/DP-210 DM-D connector...

  • Page 88: Stand-Alone Connection

    A standalone connection allows you to directly connect the customer display to the computer’s serial port. When using a TM printer, connect it to another port of the computer. The data flow when the standalone connection is as follows. DP-110/DP-210 Computer DM-D110 DM-D210 Transmit data from the computer Transmit data to the computer Power supply •...

  • Page 89: Pass-Through Connection

    A pass-through connection allows you to connect the customer display and the TM printer to one serial port of the computer. The data flow when the pass-through connection is as follows. DP-110/DP-210 Computer DM-D110 DM-D210 Transmit data from the computer TM Printer Transmit data to the computer from the TM printer...

  • Page 90: Y-Type Connection

    Transmit data to the computer from the TM printer Transmit data to the TM printer TM Printer DM-D110 DM-D210 Power supply • The data from the computer is transmitted to the TM printer and the same data is transmitted to the cus- tomer display with the Y-type connection.

  • Page 91: Precautions When Using The Usb Models

    This section explains the usage precautions when using a USB connection (self powered and bus powered). Controlled environment Precautions ✔ ✔ ✔ When using the DM-D110 Virtual COM Port Driver, set the communication speed for the dip switch to 115200 bps. ✔ ✔ ✔ Before putting Windows to system standby status, Release/Close this product. ✔...

  • Page 92: Appendix

    Appendix Appendix Product Specifications DM-D110 DM-D110 DM-D110 Model DM-D110 for TM-T88V-DT/ with DP-110 TM-T88VI-DT2 Display type Fluorescent tube display Number of characters displayed 40 characters (20 columns x 2 rows, 5 x 7 dot matrix) Display color Green (505 nm)
  • Page 93 Appendix DM-D110 DM-D110 Model DM-D110 for TM-T88V-DT/ with DP-110 TM-T88VI-DT2 Power consumption RS-232 operation: Approximately 3.6 W Approximately 2.5 W USB self power operation: Approximately 3.6 W USB bus power operation: Approximately 2.5 W Tilt angle Maximum 48° (4 steps, 5 positions) •...
  • Page 94 External dimensions 165 (W) x 110 (D) x 135 (H) mm {6.5 (W) x 4.33 (D) x 5.31" (H)} Mass Approximately 0.65 kg {Approximately 1.43 lb} DM-D110 with DP-110 and DP-105 Item Specification Display unit dimension 165 (W) x 50.5 (D) x 69 (H) mm {6.5 (W) x 1.99 (D) x 2.72" (H)} Base unit dimension 165 (W) x 110 (D) x 63 (H) mm {6.5 (W) x 4.33 (D) x 2.48"...
  • Page 95 Appendix DM-D110 for TM-T88V-DT/TM-T88VI-DT2 70 mm 177 mm Item Specification Display unit dimension 177 (W) x 70 (D) x 69 (H) mm {6.97 (W) x 2.76 (D) x 2.72" (H)} TM-T88V-DT dimension 177 (W) x 362 (D) x 202 (H) mm {6.97 (W) x 14.25 (D) x 7.95" (H)}...
  • Page 96 Appendix DM-D110 with DP-503 Item Specification Display unit dimension 165 (W) x 50.5 (D) x 69 (H) mm {6.5 (W) x 1.99 (D) x 2.72" (H)} External dimensions 165 (W) x 50.5 (D) x 317 (H) mm {6.5 (W) x 1.99 (D) x 12.68" (H)} DP-503 53 (W) x 50 (D) x 248 (H) mm {2.12 (W) x 2 (D) x 9.92"...

  • Page 97: Dm-D210

    Appendix DM-D210 Model DM-D210 DM-D210 with DP-210 Display type Fluorescent tube display Number of characters displayed 40 characters (20 columns x 2 rows, 5 x 7 dot matrix) Display color Green (505 nm) Brightness 700 cd/m2 Character classes Alphanumeric: 95 characters International characters: 37 characters Graphic characters: 128 characters x 12 pages Character composition...
  • Page 98 Appendix External Dimensions and Mass DM-D210 60 mm 260 mm Item Specification Display unit dimension 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36 (D) x 3.27" (H)} External dimensions 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36 (D) x 3.27" (H)} Mass Approximately 0.60 kg {Approximately 1.32 lb} DM-D210 with DP-210...

  • Page 99: Environmental Conditions

    Appendix DM-D210 with DP-502 260 mm 83 mm 78 mm 164 mm Item Specification Display unit dimension 260 (W) x 60 (D) x 83 (H) mm {10.24 (W) x 2.36 (D) x 3.27" (H)} External dimensions 260 (W) x 164 (D) x 360 or 480 (H) mm {10.24 (W) x 6.46 (D) x 14.17 or 18.9" (H)} DP-502 78 (W) x 164 (D) x 260 (H) mm {3.12 (W) x 6.56 (D) x 10.4"...

  • Page 100: Dp-110/Dp-210 Connector Specifications

    Appendix DP-110/DP-210 Connector Specifications This section explains the DP-110/DP-210 connector specifications. Computer Interface Connector (Serial) Type: D-Sub 25-pin connector Pin assignments Signal Signal Function Number Name Direction Frame ground • Stand-alone connection: Output Transmits data to the computer from this product •...
  • Page 101 Appendix Signal Signal Function Number Name Direction Output This indicates whether the display is ready to receive data. • [SPACE]: The display can receive data. DTR goes to SPACE under the following conditions: ∗ When the display first becomes ready to receive data after power on. ∗...
  • Page 102 Appendix Printer Interface Connector (Serial): DP-110 Type: D-Sub 9-pin connector Pin assignments Signal Signal Function Number Name Direction Input Receive data from the TM printer. (TM Printer -> Computer) Output Transmit data to the TM printer. (Computer -> TM Printer) Output Indicates whether the host is ready to receive data.
  • Page 103 Appendix Printer Interface Connector (Serial): DP-210 Type: D-Sub 25-pin connector Pin assignments Signal Signal Function Number Name Direction Frame ground Output Receive data from the TM printer. (TM Printer -> Computer) Input Transmit data to the TM printer. (Computer -> TM Printer) Input This indicates whether the display is ready to receive data from the TM printer.
  • Page 104 Appendix DM-D Connector (RS-232) Type: RJ-45 Connector Pin assignments Signal Signal Function Number Name Direction Frame ground • Stand-alone connection: Output Transmits data to the computer from this product. • Pass-through/Y-type connection Transmits data to the TM printer from the computer. Input Receives data from the computer.
  • Page 105 Appendix Power Supply Connector/Extension power cable connector Type: 3-pin locking type connector Pin assignments Signal Signal Function Number Name Direction +24V Power supply line Not used SHELL Frame ground...

  • Page 106: Serial Cable Specifications

    Appendix Serial Cable Specifications When controlling the hardware flow using the customer display and computer (DTR-DSR), use the serial cable that has the following wiring. DM-D110 Connection Type of serial cable Connection pattern Stand-Alone D-Sub 9-pin (female) / D-Sub 25-pin (male)
  • Page 107 Appendix Wiring D-Sub 9-pin (female) D-Sub 25-pin (male) D-Sub 25-pin (male) D-Sub 25-pin (male)

  • Page 108: Character Code Tables

    Appendix Character Code Tables See the Character Code Tables for Customer Displays that can be accessed from the following URL: https://support.epson.net/publist/reference_en/...

This manual is also suitable for:

Dm-d210

Table of Contents