Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for GE JNM1541DM2BB
Summary of Contents for GE JNM1541DM2BB
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. GE JNM1541DM2BB Owner's Manual Shop genuine replacement parts for GE JNM1541DM2BB Find Your GE Microwave Parts - Select From 3055 Models -------- Manual continues below --------...
- Page 2 Installation Above the Instructions Cooktop Oven JVM1540 HVM1540 JNM1541 Questions? Call 800.GE.CARES (800.432.2737) ge.com or Visit our Website at: BEFORE YOU BEGIN Read these instructions completely and carefully. Note to Consumer – • Keep these instructions for future reference. IMPORTANT –...
-
Page 3: Table Of Contents
Installation Instructions CONTENTS Recirculating ........19–22 Attach Mounting Plate to Wall ....19 General information Preparation of Top Cabinet ....19 Important Safety Instructions ........3 Adapting Blower for Electrical Requirements .......... 3 Recirculation ........20, 21 Hood Exhaust ............4, 5 Mount the Oven ......21, 22 Damage—Shipment/Installation ...... -
Page 4: Important Safety Instructions
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit checked The installer must perform a ground continuity check by a qualified electrician to make sure the receptacle is on the power outlet box before beginning the properly grounded. -
Page 5: Hood Exhaust
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 6. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. - Page 6 Installation Instructions Maximum duct length: NOTE: If you need to install ducts, note that the total ″ x 10″ rectangular or 6″ diameter duct length of 3 ⁄ For satisfactory air movement, the total duct length of round duct should not exceed 120 equivalent feet. ″...
-
Page 7: Damage-Shipment/Installation
Installation Instructions PARTS INCLUDED DAMAGE – SHIPMENT/ INSTALLATION ADDITIONAL PARTS • If the unit is damaged in shipment, return the PART QUANTITY unit to the store in which it was bought for repair or replacement. Top Cabinet • Template If the unit is damaged by the customer, repair or replacement is the responsibility of the customer. -
Page 8: Tools You Will Need
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Pencil Carpenter square # 1 and #2 Phillips screwdriver (optional) Tin snips (for cutting damper, if required) Scissors ″, ″, ″, Electric drill with ⁄ ⁄ ⁄ (to cut template, if necessary) ″... -
Page 9: Placement Of Mounting Plate
Installation Instructions PLACEMENT OF THE MOUNTING PLATE REMOVING THE OVEN FROM FINDING THE WALL STUDS THE CARTON/REMOVING THE MOUNTING PLATE Remove the turntable, installation instructions, filters, exhaust adaptor, damper, shelf and the small hardware bag. Do not remove the Styrofoam Wall protecting the front of the oven. -
Page 10: Determining Wall Plate Location
Installation Instructions DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath framed recessed Plate position – beneath flat bottom cabinet bottom cabinet Mounting Plate Tabs Mounting Plate Tabs Touching the Cabinet Touching the Back Bottom Frame 30″ to Cooktop Plate position –... -
Page 11: Aligning The Wall Plate
Installation Instructions ALIGNING THE WALL PLATE Hole B Draw a Vertical Line on Wall Hole A from Center of Top Cabinet Hole C Hole D Area E CAUTION: Wear gloves NOTE: Appearance and to avoid cutting fingers on shape of the mounting sharp edges. -
Page 12: Installation Types
Installation Instructions INSTALLATION TYPES (Choose A, B or C) This oven is designed for adaptation to the following three NOTE: This oven is shipped assembled for Outside Top types of ventilation: Exhaust (except for non-vented models). Select the type of ventilation required for your installation and proceed A. -
Page 13: Aoutside Top Exhaust
Installation Instructions OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Install Adapter A4. Mount Oven A5. Adjust Exhaust Adaptor A6. Connect Ductwork To use toggle bolts: ATTACH THE MOUNTING PLATE TO THE WALL Spacing for Toggles More Than Wall Thickness... -
Page 14: Preparation Of Top Cabinet
Installation Instructions USE TOP CABINET TEMPLATE MOUNT THE OVEN FOR PREPARATION OF TOP CABINET You need to drill holes for the top support screws, a hole large enough for the power cord to fit through, and a cutout large enough for the exhaust adaptor. FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS OVEN. -
Page 15: Adjust The Exhaust Adaptor
Installation Instructions MOUNT THE OVEN ADJUST THE EXHAUST (continued) ADAPTOR Cabinet Front Open the top cabinet and adjust the exhaust adaptor Cabinet Bottom Shelf to connect to the house duct. Filler Block Damper Equivalent to Depth of Cabinet Recess Back of Self-Aligning Screw Oven Oven Top... -
Page 16: Boutside Back Exhaust
Installation Instructions OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW B1. Prepare Rear Wall B2. Attach Exhaust Adaptor to Wall Plate B3. Attach Mounting Plate to Wall B4. Prepare Top Cabinet B5. Adjust Blower B6. Mount the Oven PREPARING THE REAR WALL ATTACH THE EXHAUST FOR OUTSIDE BACK EXHAUST ADAPTOR TO THE OVEN REAR... -
Page 17: Attach Mounting Plate To Wall
Installation Instructions USE TOP CABINET TEMPLATE ATTACH THE MOUNTING FOR PREPARATION OF TOP PLATE TO THE WALL CABINET You need to drill holes for the top support screws and a hole large enough for the power cord to fit through. Attach the plate to the wall using toggle bolts. -
Page 18: Adapting Blower For Outside
Installation Instructions ADAPTING BLOWER FOR Place the blower unit back into the opening. OUTSIDE BACK EXHAUST AFTER: Fan Blade Openings 1 Remove the two screws that hold the blower plate Facing Back and remove the screw holding the blower motor to the oven. -
Page 19: Mount The Oven
Installation Instructions Cabinet Front MOUNT THE OVEN Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess Self-Aligning Screw FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE Oven Top INSTALL THIS OVEN. Attach the oven to the top cabinet by inserting IMPORTANT: Do not grip or use handle 2 self-aligning screws through outer top cabinet during installation. -
Page 20: Recirculating
Installation Instructions RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW C1. Attach Mounting Plate to Wall C2. Prepare Top Cabinet C3. Adjust Blower C4. Mount the Oven C5. Install Charcoal Filter Place the mounting plate against the wall and ATTACH THE MOUNTING insert the toggle wings into the holes in the wall to PLATE TO THE WALL mount the plate. -
Page 21: Adapting Blower For Recirculation
Installation Instructions ADAPTING BLOWER Roll the blower unit 90° so that fan blade openings are facing toward the front of the oven. FOR RECIRCULATION BEFORE: Fan Blade NOTE: The exhaust adaptor with damper is not Openings Facing Up needed for recirculating models. You may want to save them for possible future use. -
Page 22: Mount The Oven
Installation Instructions NOTE: When mounting ADAPTING BLOWER FOR the oven, thread power RECIRCULATION (continued) cord through hole in bottom of top cabinet. Place the blower unit back into the opening. Keep it tight throughout CAUTION: Do not pull or stretch the blower unit Steps 1–3. -
Page 23: Installing The Charcoal Filter
Installation Instructions WHEN REPLACING THE MOUNT THE OVEN CHARCOAL FILTER (continued) If the model is not vented to the outside, the air will Attach the oven to the top cabinet by inserting be recirculated through a disposable charcoal filter 2 self-aligning screws through outer top cabinet that helps remove smoke and odors. -
Page 24: Before You Use Your Oven
Installation Instructions BEFORE YOU USE YOUR OVEN Make sure the oven has been installed Read the Owner’s Manual. according to instructions. KEEP INSTALLATION INSTRUCTIONS FOR THE LOCAL INSPECTOR’S USE. Remove all packing material from the oven. Install turntable and wheeled ring in cavity. Replace house fuse or turn breaker back on. - Page 25 Printed in China...