Components ..................................15 Control Boards and Panel Connections .........................13 Control Features ................................6 Control Panel Assembly ..............................17 Cooling Fan Motor ................................21 Demo Mode (JVM1750) ..............................10 Diagnostics and Service Information ........................26 Door Assembly ...................................25 Door Interlock Switches ..............................24 Duct Assembly ...................................18 Grill Assembly ..................................16 High Voltage Transformer ............................23...
Nomenclature Model Number J V M 1 7 5 0 D P 1 B B Product J = GE Cooking Product Product Color BB = Black Microwave Oven WW = White V = Externally Vented SS = Stainless Steel Over-the-Range...
Introduction The GE Spacemaker Over-the-Range Microwave Oven is a versatile appliance for any kitchen. Features and Benefi ts: Sensor Cook - The microwave oven automatically adjusts the cooking time to various types and amounts of food. Auto and Time Defrost - Auto defrost sets the defrosting time and power levels to deliver even defrosting results for up to 6 pounds of meats, poultry, and fi...
Control Features JVM1750 Features 1 Door Handle. Pull to 4 Shelf. Lets you 8 Removable Turntable. open the door. The microwave several Turntable and support door must be securely foods at once. Food must be in place latched for the microwaves best when when using the oven.
Page 7
4 Touch Control Panel. Available at an extra 5 Cooktop Light. cost from your GE 6 Grease Filter. supplier, or see GE Service Numbers. 10 Rating Plate . Located on the inside wall of the microwave oven.
Page 8
JVM1750 Controls Time Features Time Cooking Press Enter TIME COOK I & II (Press once or twice) Amount of cooking time. DEFROST AUTO/TIME (Press twice) Amount of defrosting time. EXPRESS COOK Starts immediately! POWER LEVEL Power level 1–10. ADD 30 SEC...
Page 9
JVM1540 Controls You can microwave by time, temperature or with the convenience features. Time Features Time Cooking Press Enter TIME COOK I & II (Press once or twice) Amount of cooking time. DEFROST AUTO/TIME (Press twice) Amount of defrosting time. EXPRESS COOK Starts immediately! POWER LEVEL...
Demo Mode (JVM1750) • To enter the Demo Mode, touch and hold the HELP pad for a full 3 seconds. • To end the Demo Mode, touch and hold the HELP pad for a full 3 seconds. • As pads are pressed in the Demo Mode, explanations of the pads' functions will be scrolled across the display screen.
Component Locator Views Front View Grill Assembly Control Panel Assembly Turntable Shaft Front View - Control Panel Assembly Removed Cooling Fan Motor Hood TCO Bottom TCO (Continued Next Page) – 11 –...
Page 12
Right Side View Fuse High Voltage Capacitor Diode Vent Motor Capacitor Magnetron TCO Magnetron Cooling Fan Motor Cooling Fan High Voltage Transformer Hood TCO Bottom TCO – 12 –...
Components Oven Removal The oven is hooked on metal tabs at the bottom of the wall mounting plate and fastened to the cabinet with 3 top cabinet bolts. To remove the oven from the cabinet or wall opening: WARNING: This oven requires 2 people for complete 3.
6. Remove 2 Phillips-head screws from the left side 4. Lift out the vent blower and place it on top of the of the oven. oven side as shown below and disconnect the electrical connector to the vent blower. Electrical Connector View From Rear 7.
To remove the grill assembly (Model JVM1750): 4. Gently remove the bulb. Open the door. Remove 2 Phillips-head screws from the top, front of the oven cabinet. Remove 1 Phillips-head screw from the right, rear corner of the grill. 4. Slide grill to the left and remove.
5. Tilt the top of the control panel out, and Cavity Thermal Cutout mark and disconnect all the wiring harnesses connected to the smart board. The cavity thermal cutout is located on the top side of the oven cavity beside the exhaust duct. The 6.
4. Disconnect wiring to the magnetron TCO. Bottom Thermal Cutout (TCO) 5. Remove 2 Phillips-head screws that attach the The bottom TCO is located on the bottom, right side magnetron TCO to the magnetron. of the oven behind the control panel. The bottom TCO is not resettable.
Check to make sure the fuse is not open. Check the Stirrer Assembly noise fi lter for approximate resistance value at the following locations: The stirrer assembly consists of a blade, pin, and cover. The blade is air driven and rotates on a shaft White (neutral input) to white (neutral output) - 0 Ω.
Magnetron WARNING: Prior to servicing the magnetron, be Disconnect certain the capacitor is discharged. Manually discharge by placing an insulated-handle screwdriver between the diode connection of the capacitor and the oven chassis ground. To remove the magnetron: Remove the outer cover. (See Outer Cover Disconnect wiring to the magnetron.
Page 22
5. Disconnect wiring to the primary of the high 8. Using a small fl at blade screwdriver, carefully voltage transformer. remove the fan retainer. Fan Retainer Disconnect View From Right Side 6. Remove 3 Phillips-head screws attaching the cooling fan frame to the microwave. 9.
Capacitor and Diode Disconnect The capacitor has an internal shunt resistor to automatically discharge the capacitor when the oven turns "off". Under normal operation, the capacitor should fully discharge within 30 seconds. WARNING: Always be certain the capacitor is Disconnect discharged before servicing.
3. Remove the 2 Phillips-head screws that attach Door Interlock Switches the door switch bracket to the microwave oven frame and remove the door switch bracket. The door has 3 interlock switches. All switches are removed the same way. Door Sensing and Primary Interlock Switches The power relay is mounted on the smart board.
Surface Lamps The surface lamps are 120V, 40-watt incandescent bulbs (part number WB06X10823). Note: Model JVM1750 has two bulbs. The JVM1540 model has a single bulb. To remove the surface lamp assemblies: Disconnect Remove the Phillips-head screw from the surface lens panel, then open the panel.
6. Test the circuit operation: Interlocks (Door Latch Switches) a. Connect temporary jumper across relay The interlocks are designed as follows: contacts and primary switch to simulate shorted switch contacts. Locate convenient Primary - Bottom switch operated by bottom latch connections in circuit to be certain COM pawl connected to line (L) leg.
If necessary, the key panel pads can be verifi ed by a continuity test. For ease of handling, the key panel should be removed and placed on a fl at surface. Check the continuity between the connections at the end of the ribbon. (Use high Ω scale.) RIBBON (JVM1750, HVM1750, EVM1750) CONN. CONN.
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service Location for service.