Miele PM 1210 Operating Instructions Manual
Commercial flatwork ironer
Hide thumbs
Also See for PM 1210:
- Operating instructions manual (42 pages) ,
- Quick manual (2 pages) ,
- Operating instructions manual (28 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Miele PM 1210
Summary of Contents for Miele PM 1210
- Page 1 Operating instructions Commercial flatwork ironer PM 1210 PM 1214 PM 1217 To avoid the risk of accidents or damage to the en-GB machine, it is essential to read these instructions before it is installed and used for the first time.
-
Page 2: Table Of Contents
Peak load (optional accessory).................... 15 Fault messages........................16 Cleaning and care......................17 Cleaning and waxing the heater plate ................. 17 Waxing the heater plate....................... 17 Roller padding ........................18 Removing the roller cover....................18 Fitting the roller cover......................18 Miele Service ........................19... -
Page 3: Warning And Safety Instructions
Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Repairs may only be carried out by a Miele authorised service technician. ... -
Page 4: Operation
Miele cannot be held liable for damage or injury caused by the lack of or inadequacy of an effective earthing system. - Page 5 Warning and Safety instructions Remove rings and bracelets before ironing. Smooth out folds as far away from the infeed on the infeed table as possible. Feed pil‐ low cases and duvet covers into the ironer with the open end first. Do not take hold of the corners from the inside.
-
Page 6: Caring For The Environment
Caring for the environment Disposal of the packing material The packaging is designed to protect the machine from damage during transportation. The packaging materials used are selected from materials which are environmentally friendly for disposal and should be recycled. Recycling the packaging reduces the use of raw ma‐ terials in the manufacturing process and also reduces the amount of waste in landfill sites. -
Page 7: Guide To The Machine
Finger guard i Height adjustable screw feet d Roller j Plinth (optional) e Heater plate with cover k Laundry box f Laundry outfeed table Option PM 1210 PM 1214 PM 1217 Swing out bar Flexible laundry feed Spring padding Plinth... -
Page 8: Control Buttons On The Touch Display
Increase temperature / roller speed p Roller speed selection button 3 * This button can be activated by Miele Service during commissioning. When a button is pressed, it is highlighted with a bar underneath. When the button flashes, the ironer can be started. -
Page 9: Display Symbols On The Control Panel
Guide to the machine Display symbols on the control panel a Activate the finger guard g Pre-selection and temperature display in °C / °F b Heating on / temperature increasing h Pre-selection and roller speed display c Cleaning and waxing (PM 1217 only) i Roller speed range d Heating off / temperature too high j Coin operation mode... -
Page 10: Finger Guard
Guide to the machine Finger guard Flexible laundry feed for through‐ feed The finger guard is a safety feature which (Optional accessory for PM 1217) must be checked daily for proper func‐ tioning before the machine is used. The flexible laundry feed mechanism ena‐ bles laundry to be fed through to the back of the ironer for removal. -
Page 11: Laundry Preparation
For a good result and optimum ironing per‐ formance the ideal residual moisture level for the PM 1214 and PM 1217 lies between 15% and 25%, for the PM 1210 at 15%. The ideal residual moisture level depends on the composition of the fabric. -
Page 12: Operation
Operation Preparing for use Material Symbol Tempera‐ Pre-set val‐ ture Switch on the on-site mains switch. Nylon / Artifi‐ 100 - 110 °C 110 °C cial silk Switch the ironer on by pressing the On / Off button. ... -
Page 13: Selecting The Ironer Speed
Keep it pressed in. The bar will light up un‐ derneath it and the current roller speed will Selecting the ironer speed appear in the display. PM 1210 / PM 1214: Press the "Increase roller speed" or Symbol Speed range "Decrease roller speed"... -
Page 14: Standby Mode
Standby mode is switched off at the factory. After ironing let the roller run for approx. 5 It can be reactivated by Miele Service. The minutes on minimum heating to let the time interval after which the ironer switches roller covering dry out. -
Page 15: Notes
Power failure during ironing The temperature unit display can be In the event of a power failure, the heater changed from °C to °F by Miele Service. plate withdraws automatically. When power is restored you need to restart the ironer by Favourites setting pressing the ... -
Page 16: Fault Messages
Notes Fault messages In the event of a malfunction call Miele Service. When a fault occurs ironing is interrupted, the "Pause" button flashes and a four-dig‐ it code appears in the display. Pressing the flashing "Pause" button cancels the fault (the fault is stored in the fault memory). -
Page 17: Cleaning And Care
When the motor and the roller cover. Please follow waxing has been successfully carried out in the notes in the Miele Ironing Handbook on waxing mode, the interval for the cleaning ironing and cleaning and care. The heater... -
Page 18: Roller Padding
Otherwise there is the risk of damage to Recovering the roller with wire wool must the leaf-type roller padding. only be carried out by Miele Service. The diameter of a new or re-upholstered roller must not be less than the following... -
Page 19: Miele Service
Miele Service In the event of a fault, contact Miele Serv‐ ice. Miele Service will require the model (M- Nr) and serial number (SN). This information is given on the data plate. - Page 20 Tel: +971-4-341 84 44 E-Mail: info@miele.ie, Internet: www.miele.ie Fax: +971-4-341 88 52 Manufacturer: Miele & Cie. KG E-Mail: info@miele.ae Carl-Miele-Straße 29, 33332 Gütersloh, Germany Internet: www.miele.ae Alteration rights reserved / Publication date: 0415 M.-Nr. 10 025 800 / 01 ...