Table of Contents
Advertisement
Quick Links
ATS1235 Advanced Wireless DGP on 868 MHz
AM Installation Sheet
EN
1
TAMPER
USB
TERM
12V
0V
D+
CON3
D-
3
METAL
© 2011 UTC Fire & Security. All rights reserved.
CON1
SW1 (Tamper)
METAL
2
CA1
DA1
RA1
DA2
CA2
RA2
DA3
CA3
LA1
RA3
CA4
DA4
CA16
RA4
X2
CF1
DF1
R10
RF1
DF2
CF2
RF2
DF3
CF3
LF1
RF3
CF4
DF4
CF16
RF4
X1
C11
C12
C128
C8
IC2
R7
C10
C9
R22
R20
R21
R19
R18
R17
R16
R15
R13
CON3
4
Address Setting
Address Setting
1
1000
6
2
0100
7
3
1100
8
4
0010
9
5
1010
10
Example:
ON
"1"
"0"
1
2
3
4
Address 1
1 / 8
C23
R9
or
L3
R8
C22
C21
RA5
CA5
CA6
CA7
CA10
LA2
LA4
CA13
CA15
ICA1
ZA1
CA11
LA5
CA9
LA3
CA8
CA12
RA6
RF5
CF15
CF5
CF6
CF7
CF10
LF2
LF4
CF13
ICF1
ZF1
CF11
LF5
CF9
LF3
CF8
CF12
RF6
C6
D3
C5
IC3
C4
C3
D2
R183
R14
IC1
R4
C14
R3
C2
R12
C15
C13
R2
T2
1
C1
or
C7
R1
T1
2
R11
3
D1
R5
R6
D4
4
5
CON1
Address Setting
0110
11
1101
1110
12
0011
0001
13
1011
1001
14
0111
0101
15
1111
ON
"1"
"0"
1
2
Address 2
P/N 1070346 • REV 1.0 • ISS 17JAN11
L4
L1
or
L2
C20
3
4
Advertisement
Table of Contents
Related Manuals for GE ATS1235
Summary of Contents for GE ATS1235
- Page 1 ATS1235 Advanced Wireless DGP on 868 MHz AM Installation Sheet TAMPER CA10 CA13 CA15 ICA1 CA11 CA16 CA12 CF15 CF10 CF13 ICF1 CF11 TERM CF16 CF12 C128 R183 CON3 CON1 CON3 CON1 SW1 (Tamper) Address Setting Address Setting Address Setting...
- Page 2 Set Defaults? 0-Exit, Menu: _ *=Yes, #=No: GE and the GE monogram are trademarks of the General Electric Company and are under license to UTC Fire & Security, 9 Farm Springs Road, Farmington, CT 06034-4065. 2 / 8 P/N 1070346 • REV 1.0 • ISS 17JAN11...
-
Page 3: Basic System Description
Basic system description EN: Installation Sheet The ATS control panel collects the data from the wireless DGP on the data bus. The ATS1235 can be powered by the control panel, or by a remote, 220 V powered DGP. Introduction The ATS1235 receives the RF signal from the wireless The ATS1235 Advanced Wireless DGP on 868 MHz AM devices, such as fobs, PIR sensors, or smoke detectors. -
Page 4: Introduction To Programming
Sensor / key fob documentation is available or known. Before powering up the panel and receiver module, verify • The DIP switch address for the wireless DGP is set that all wiring at the panel and ATS1235 wireless receiver correctly. is correct. •... - Page 5 How to configure a wireless sensor and Number of detectors with long supervisory fail program a zone on an ADVISOR MASTER Number of smoke detectors reporting dirty Enter the Installer Menu 19: Jamming Menu key, Installer PIN, Enter Jamming is detected by the receiver. 19, Enter A jamming condition occurs if there are more than 30 seconds of jamming within any one minute interval.
-
Page 6: Supervision Time
Short supervision To ensure the sensor is installed within an effective range of • Long supervision the ATS1235 or repeater, the installer can check the signal • Smoke supervision strength of a wireless sensor’s last event transmission on the RAS screen. -
Page 7: Specifications
The factory default for supervision is “on”. • TX-2211-03-1 Wireless PIR motion sensor, 868 MHz GEN2 Two- and four-button fobs do not transmit a supervision signal; when fobs are programmed, they automatically set supervision • TX-2212-03-1 Mirror PIR, 868 MHz GEN2, Pet Immune to “off”. -
Page 8: Contact Information
Contact information For contact information see our Web site: utcfireandsecurity.com. 8 / 8 P/N 1070346 • REV 1.0 • ISS 17JAN11...