Advertisement
Quick Links
48in, 52in, and 60in Recycler
Model No. 147-0310
Model No. 147-0315
Model No. 147-0320
Note:
For optimal performance, use this kit with Recycler blades (sold separately).
Safety
An uncovered discharge opening allows objects to be thrown toward you or
bystanders. Also, contact with the blade could occur. Thrown objects or blade
contact will cause serious injury or death.
Do not operate the mower with the discharge deflector raised, removed, or altered
unless a grass collection system or mulch kit is in place and working properly.
Preparing the Machine
1. Park the machine on a level surface, disengage the PTO, and engage the parking brake
(if applicable).
2. Shut off the machine, remove the key, and wait for all moving parts to stop before
leaving the operating position.
3. For electric machines, turn the battery-disconnect switch to the O
machines with a lead-acid battery, disconnect the negative (black) cable from the
negative (-) battery post.
4. Repair all bent or damaged areas of mower deck and replace any missing parts.
5. Clean the machine of any debris on the deck to ease installation.
6. Raise the front of the machine so that you can access beneath the mower deck. Support
the machine using jack stands rated for the weight of the machine.
Mechanical or hydraulic jacks may fail to support the machine and cause a serious
injury.
• Do not rely solely on mechanical or hydraulic jacks to support the machine.
• Support the machine with jack stands whenever you raise the machine.
© 2023—The Toro
®
Company
8111 Lyndale Ave So
Bloomington, MN 55044
DANGER
WARNING
Register at www.Toro.com
®
Kit
Installation Instructions
FF
Original Instructions (EN)
Printed in the USA
All rights reserved
3465-647A
position; for
*3465-647* A
Advertisement
Related Manuals for Toro 147-0310
Summary of Contents for Toro 147-0310
- Page 1 3465-647A 48in, 52in, and 60in Recycler ® Model No. 147-0310 Model No. 147-0315 Model No. 147-0320 Installation Instructions Note: For optimal performance, use this kit with Recycler blades (sold separately). Safety DANGER An uncovered discharge opening allows objects to be thrown toward you or bystanders.
- Page 2 7. Remove the existing blades; refer to the Operator's Manual for the machine. Removing the Existing Baffles For Mower Decks with Existing Baffles G428581 1. Remove the baffles from the mower deck. Retain the baffles and hardware. Note: Remove the nuts before removing the bolts. 2.
-
Page 3: Drilling Holes
Removing the Discharge Chute 1. Remove the locknut , bolt , spring , and spacer holding the grass deflector to the pivot brackets. 2. Remove the grass deflector. Note: Retain the hardware that you removed during this procedure so that it is available for changeover. - Page 4 Installing the Discharge Plate Parts Required Discharge plate Carriage bolt (3/8 x 1-1/4 inches) Carriage bolt (5/16 x 7/8 inch) Flange nut (small flange) (3/8 inch) Flange nut (5/16 inch) 1. Install the discharge plate to the outside of the mounting bracket with 2 carriage bolts (3/8 x 1-1/4 inches) and 2 flange nuts (small flange) (3/8 inch)
- Page 5 Installing the Baffles 48 Inch Decks Parts Required Left baffle Center baffle Right baffle Carriage bolt (3/8 x 1 inch) Flange nut (large flange) (3/8 inch) Bolt (3/8 x 1 inch) Flange nut (small flange) (3/8 inch) Side plate (Grandstand decks only) Note: Loosely install the baffles to align the baffles with all holes in the mower.
- Page 6 4. Position the left baffle into the mower. 5. Loosely install the left baffle to the top of the mower deck with 1 bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch) 6. Loosely install the left baffle to the side of the mower deck with 2 carriage bolts (3/8 x 1 inch) and 2 flange nuts (large flange) (3/8 inch) G468249...
- Page 7 Installing the Baffles 52 Inch Decks Parts Required Left baffle Center baffle Right baffle Carriage bolt (3/8 x 1 inch) Flange nut (large flange) (3/8 inch) Bolt (3/8 x 1 inch) Flange nut (small flange) (3/8 inch) Side plate (Grandstand decks only) Note: Loosely install the baffles to align the baffles with all holes in the mower.
- Page 8 7. Position the center baffle into the mower. 8. Loosely install the center baffle to the left baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch) 9. Loosely install the center baffle to the right baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch).
- Page 9 Installing the Baffles 60 Inch Decks Parts Required Left baffle Center baffle Right baffle Carriage bolt (3/8 x 1 inch) Flange nut (large flange) (3/8 inch) Bolt (3/8 x 1 inch) Flange nut (small flange) (3/8 inch) Side plate (Grandstand decks only) Note: Loosely install the baffles to align the baffles with all holes in the mower.
- Page 10 7. Position the center baffle into the mower. 8. Loosely install the center baffle to the left baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch) 9. Loosely install the center baffle to the right baffle with 1 carriage bolt (3/8 x 1 inch) and 1 flange nut (small flange) (3/8 inch).
- Page 11 Installing the Trailing Shield For Electric-Grandstands Parts Required Trailing shield Shoulder bolt WARNING Using a drill without proper eye protection may allow debris to enter the eye, causing injury. When drilling, always wear eye protection. 1. Use the provided template to locate and drill the 2 holes required for the trailing shield assembly.
- Page 12 Trailing Shield Template G468379 Page 12 3465-647 A...
-
Page 13: Completing The Installation
Installing the Recycler Blades Parts Required Recycler blade (sold separately) 1. Install the 3 recycler blades; refer to the Operator’s Manual. 2. Rotate the blades and ensure that there is clearance between the blades and baffles. If there is interference, loosen the baffle and reposition it. Completing the Installation 1. - Page 14 Notes:...
- Page 15 Notes:...