Table of Contents
Advertisement
Quick Links
Register at www.Toro.com.
Original Instructions (EN)
11 and 14-Blade Cutting Unit
Greensmaster
Traction Units
Model No. 04251—Serial No. 314001001 and Up
Model No. 04252—Serial No. 314001001 and Up
Model No. 04253—Serial No. 314001001 and Up
Model No. 04254—Serial No. 314001001 and Up
Form No. 3385-370 Rev C
®
Flex
™
/eFlex
®
1800/2100
*3385-370* C
Advertisement
Table of Contents
Related Manuals for Toro Greensmaster 04251
Summary of Contents for Toro Greensmaster 04251
- Page 1 ® 1800/2100 Traction Units Model No. 04251—Serial No. 314001001 and Up Model No. 04252—Serial No. 314001001 and Up Model No. 04253—Serial No. 314001001 and Up Model No. 04254—Serial No. 314001001 and Up *3385-370* C Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
2 Using the Cutting-Unit Prop......4 additional information, contact an Authorized Service 3 Adjusting the Bedknife to the Reel ....4 Dealer or Toro Customer Service and have the model 4 Adjusting the Rear Roller ......... 6 and serial numbers of your product ready. -
Page 3: Safety
If major repairs are ever needed or if assistance is • Never operate the cutting units while ill, tired, or desired, contact an authorized Toro distributor. under the influence of drugs or alcohol. • To ensure optimum performance and continued •... -
Page 4: Setup
Setup Media and Additional Parts Description Qty. Operator's Manual Read this before installing and operating cutting unit. Parts catalog Use this to reference part numbers. Certification of compliance Save this for future reference. Target plate Install these parts if you are using an eFlex traction unit. Weight bar Installing the Front Roller No Parts Required... - Page 5 Note: Ensure that the nuts or back of the adjusting screw counterclockwise moves the bedbar adjusting screws are not resting on the bedknife edge away from the reel. work surface (Figure Test the cutting performance by inserting a long Rotate the reel so that 1 of the blades crosses strip of cutting performance paper between the the bedknife edge between the first and second reel and bedknife, perpendicular to the reel...
-
Page 6: Adjusting The Rear Roller
Remove the 2 nuts securing each roller bracket and spacer to each sideplate mounting flange. Lower the roller and screws from the sideplate mounting flanges and spacers. Adjusting the Rear Roller Place the spacers onto the screws above of below the roller brackets, as required (Figure 6 Figure No Parts Required... -
Page 7: Adjusting The Height Of Cut
Adjusting the Height of Cut No Parts Required Procedure Note: This cutting unit comes standard with the Edgemax Micro-cut bedknife and standard bedbar. The effective height of cut is dependent on previous mower configurations and turf conditions (i.e., roller type, bedknife behind center distance, soft or firm greens, season conditions). -
Page 8: Adjusting The Cut-Off Bar
Adjusting the Cut-off Bar No Parts Required Procedure g016945 Figure 11 Adjust the cut-off bar to ensure that the clippings are 1. Gauge bar cleanly discharged from the reel area as follows. Loosen the screws securing the top bar (Figure Rotate the adjusting screw until the roller 12) to the cutting unit. -
Page 9: Preparing The Cutting Unit For Use On An Eflex Machine
Preparing the Cutting Unit for Use on an eFlex Machine Parts needed for this procedure: Target plate Weight rod (supplied with your traction unit) Flange-head bolt (supplied with your traction unit) Installing the Target Plate • If you will be using the cutting unit on an eFlex traction unit, install the provided target plate, then adjust the machine sensors as described in the g017294... - Page 10 Secure the threaded end of the weight rod to the frame using a flange-head bolt (Figure 15). g026124 Figure 15 1. Flange-head bolt 2. Weight rod...
-
Page 11: Product Overview
11-Blade—30.8 kg (68 lb); 14-Blade—32.2 kg (71 lb) Attachments/Accessories A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a... -
Page 12: Operation
Operation impact on energy consumption. Very light contact is recommended for optimum cutting performance and battery consumption. Note: Determine the left and right sides of the Note: As the reel blades continue to run against machine from the normal operating position. the bedknife, a slight burr will appear on the The dual point bedknife-to-reel adjustment system front cutting edge surface along the full length... - Page 13 Install the belt. Ensure that the compression spring is applying tension to the belt (Figure 17). Tighten the bearing-housing nut. Install the belt cover. g017116 Figure 17 1. Bearing-housing nut 3. Compression spring 2. Reel drive belt Using a 16 mm (5/8 inch) wrench, rotate the bearing housing to make sure it operates freely.
-
Page 14: Maintenance
Maintenance Remove each bedbar bolt allowing the bedbar to be pulled downward and removed from the machine bolt (Figure 20). Note: Determine the left and right sides of the Account for the 2 nylon and 2 stamped steel machine from the normal operating position. washers on each end of the bedbar (Figure 21). -
Page 15: Backlapping The Reel
Connect the backlapping machine to the cutting unit by connecting a 1/2 inch hex socket to the reel pulley output shaft on the left side of the cutting unit. Note: Additional instructions and procedures on Backlapping are available in the Toro... - Page 16 Notes:...
- Page 17 Notes:...
- Page 18 Notes:...
- Page 19 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
- Page 20 Countries Other than the United States or Canada Customers who have purchased Toro products exported from the United States or Canada should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer.