Page 1
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2005 T –...
Page 2
The interlock mechanism mentioned above becomes invalid in this mode. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : Refer to page 89 on the service manual RRV3216. XV-EV500...
Page 3
5.62k Ω → 562 × 10 → 5621 ............RN1/4PC 5 6 2 1 CONTRAST TABLE XV-EV500/DFXJ, DDXJ/RB, DTXJ and DLXJ/NC are constructed the same except for the following : Part No. Ref. Mark Symbol and Description XV-EV500 XV-EV500 XV-EV500...
Page 4
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936 PIONEER CORPORATION 2005 T-ZZK AUG.
The interlock mechanism mentioned above becomes invalid in this mode. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. ∗ : Refer to page 89. XV-EV500...
Page 6
To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. XV-EV500...
7.1.8 DVD TROUBLE SHOOTING......................96 7.1.9 ID NUMBER AND ID DATA SETTING ....................99 7.1.10 DISASSEMBLY..........................102 7.2 PARTS..............................112 7.2.1 IC ..............................112 7.3 EXPLANATION ............................115 7.3.1 SEQUENCE AFTER POWER ON....................115 7.3.2 PROTECTION CIRCUIT........................116 8. PANEL FACILITIES ............................121 XV-EV500...
Multi voltage model ..AC 110-127/220-230/ 240 V (switchable), 50/60 Hz Accessories • Power cord • FM Antenna (ADH7030) • Video Cord (ADG1154) (L = 1.5m) (XDE3046) Yellow • AM Loop Antenna • Dry Cell Batteries (ATB7013) • Remote Control (XXD3097) XV-EV500...
Page 9
DVD Format/Logo Licensing Corporation • Also compatible with KODAK Picture CD This player supports the IECís Super VCD stan- dard for superior picture quality, dual soundtracks, and widescreen support. VIDEO Super Video CD (Super VCD) XV-EV500...
For the applying amount of lubricants or glue, follow the instructions in this manual. (In the case of no amount instructions, apply as you think it appropriate.) 2.1 PACKING Yellow XV-EV500 Junction PACKING SECTION PARTS LIST Mark No. Description Part No.
Refer to Refer to "2.2 EXTERIOR "2.2EXTERIOR SECTION. " SECTION. " Refer to "2.2 EXTERIOR SECTION. " Cleaning paper GED-008 Refer to Refer to "2.2 EXTERIOR "2.2 EXTERIOR SECTION. " SECTION. " Refer to "2.4 FRONT PANEL SECTION. " XV-EV500...
Page 14
Heat Sink XNH3038 NSP 11 Chassis Hal XNA3025 AMP Support F XNG3141 AMP Support R XNG3142 NSP 14 Spacer AEB7092 Rubber Cushion XEB3047 LEG Cushion R XEB3050 Binder ZCA-SKB90BK Screw BBZ30P060FTC Screw BBZ30P080FNI Screw BBZ40P060FTC Screw BBZ30P140FTC Screw BBZ30P300FTC XV-EV500...
Page 18
Rear View Daifree Daifree No. 23 No. 23 GEM1036 GEM1036 Tray Tray Concave of unevenness Concave of unevenness Inner side of a ditch Daifree GEM1036 Top View Bottom View Side of the rib Concave of unevenness Daifree Daifree GEM1036 GEM1036 XV-EV500...
Part No. Cable Assy XDE3066 Main Belt FF20B-13A 11P F.F.C/60V XDD3184 F/R Belt FF19S-31 Plate HD Blk F513-926 Roller Pinch Blk R F514-133 Roller Pinch Blk L F514-134 Clutch Assy Blk F522-063 Motor Main Blk F525-394 PCB Control Blk F567-747 XV-EV500...
• The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. • : The power supply is shown with the marked box. XV-EV500...
: TRACKING SERVO LOOP LINE : STEPPING SERVO LOOP LINE (C/V) : VIDEO SIGNAL ROUTE (R/Cr) : VIDEO SIGNAL ROUTE(R/Cr) (G/Y) : VIDEO SIGNAL ROUTE(G/Y) (B/Cb) : VIDEO SIGNAL ROUTE(B/Cb) (S_Y) : S VIDEO SIGNAL ROUTE (S_C) : S VIDEO SIGNAL ROUTE XV-EV500...
Page 28
(R/Cr) (B/Cb) (R/Cr) : AUDIO SIGNAL ROUTE (C/V) : VIDEO SIGNAL ROUTE (R/Cr) : VIDEO SIGNAL ROUTE(R/Cr) (G/Y) : VIDEO SIGNAL ROUTE(G/Y) (B/Cb) : VIDEO SIGNAL ROUTE(B/Cb) (S_Y) : S VIDEO SIGNAL ROUTE (S_C) : S VIDEO SIGNAL ROUTE XV-EV500...
Page 32
: AUDIO SIGNAL ROUTE (DVDL) : AUDIO SIGNAL ROUTE (DVD L ch) (AUX) C8829 STBY (DVDR) : AUDIO SIGNAL ROUTE (DVD R ch) : AUDIO SIGNAL ROUTE (TX) VA-12 (FL) : AUDIO SIGNAL ROUTE (Front L ch) : AUDIO SIGNAL ROUTE (TC) XV-EV500...
Page 36
: AUDIO SIGNAL ROUTE (Front L ch) (FL) UNLESS OTHERWISE SPECIFIED (FR) : AUDIO SIGNAL ROUTE (Front R ch) 1/16W 1/4WPU ALL COILS ARE IN µH (TC) : AUDIO SIGNAL ROUTE UNLESS OTHERWISE SPECIFIED LAU***J ALL DIODES ARE 1SS133 UNLESS OTHERWISE SPECIFIED 1SS133 MA111 MTZJ*** XV-EV500...
Page 40
MIC IN R5404 R5405 8.2k R5406 R5407 51048-0400 D20PYY0430E J3902 HPDET (FR) HP R GNDHP (FL) HP L (FL) : AUDIO SIGNAL ROUTE (Front L ch) (FR) : AUDIO SIGNAL ROUTE (Front R ch) (MIC) : AUDIO SIGNAL ROUTE XV-EV500...
Page 44
CAUTION : FOR CONTINUED PROTECTION AGAINST (FR) (HPR) RISK OF FIRE. REPLACE ONLY WITH : AUDIO SIGNAL ROUTE (Front R ch) : AUDIO SIGNAL ROUTE SAME TYPE NO. 491007 MFD, BY (LRMIX) : AUDIO SIGNAL ROUTE LITTELFUSE INK. FOR IC3101 (AEK7047). XV-EV500...
Page 48
ALL RESISTORS ARE IN UNLESS OTHERWISE SPECIFIED RS1/4PU***J RS1/16S***J DIODE 1SS133 MA111 MTZJ*** • NOTE FOR FUSE REPLACEMENT ALL VOLTAGE'S AT POWER ON CONDITION CAUTION - FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE WITH SAME TYPE AND RATINGS OF FUSE. XV-EV500...
IC22 STBY BLAC2 BHAC2 SUBAC1 SUBAC1 NOTES ALL RESISTORS ARE IN ALL CAPACITORS ARE IN µF UNLESS OTHERWISE SPECIFIED 1/16W YF : CKSRYF 1/4WPU (OTHER : CKSRYB) DIODE M : CQMBA 1SS133 AL : CEAL (OTHER : CEAT***M##) MA111 XV-EV500...
Page 50
UN8V GNDTX GNDS D5SBA20(B) 6800/25 IC41 (7A) AEK7021- TUBE:ADN7004 GNDD GNDMDV CAUTION : FOR CONTINUED PROTECTION AGAINST RISK OF FIRE. REPLACE ONLY WITH SAME TYPE NO. 491007 MFD, BY GNDMTC UN8V LITTELFUSE INK. FOR IC41 (AEK7021). UN8V GNDTX GNDTX XV-EV500...
4.4 KEY, LED and DISPLAY ASSYS SIDE A SIDE A CN5501 DISPLAY ASSY CN5101 CONTACT W726 ONUPPER SIDE W728 W729 LCD ASSY W737 (XNP3096-C) LED ASSY (XNP3096-C) KEY ASSY XWZ4013 KEY ASSY PNE-1B1 OPEN/CLOSE STOP S5301 S5303 PLAY <<| >>| S5305 S5302 S5304 (XNP3096-C) XV-EV500...
Page 60
SIDE B SIDE B DISPLAY ASSY CN5101 Q5101 Q5102 Q5204 (XNP3096-C) R5226 R5225 R5227 LED ASSY C5212 D5221 D5225 D5219 Q5220 Q5219 (XNP3096-C) KEY ASSY KEY ASSY XWZ4013 OPEN/CLOSE STOP PNE-1B1 >>| <<| PLAY GNDU 1.KEY3 (XNP3096-C) XV-EV500...
Q 305 (A,84 ,125 ) NMOS FET TRANSISTOR UM5K1N D 862 (A,46 ,83 ) DIODE 1SS355 Q 307 (A,71 ,87 ) CHIP TRANSISTOR HN1A01F D 881 (A,46 ,93 ) DIODE 1SS355 Q 308 (A,63 ,87 ) CHIP TRANSISTOR HN1A01F L 731 (A,23 ,109 ) POWER INDUCTOR(22U) DTL1099 XV-EV500...
Page 70
R 512 (A,97 ,60 ) RS1/16S223J R 244 (A,69 ,41 ) RS1/16S330J R 513 (A,103 ,59 ) RS1/16S471J R 247 (B,58 ,37 ) RS1/16S103J R 514 (A,95 ,59 ) RS1/16S471J R 248 (B,58 ,46 ) RS1/16S330J R 515 (A,99 ,56 ) RS1/16S222J XV-EV500...
Page 71
C 250 (B,64 ,36 ) CKSRYB103K50 R 1002(B,116 ,16 ) RS1/10S0R0J C 251 (A,73 ,47 ) CCSRCH8R0D50 R 1003(B,118 ,16 ) RS1/10S0R0J C 252 (A,73 ,44 ) CCSRCH100D50 C 253 (B,64 ,44 ) CKSRYB104K25 CAPACITORS C 254 (B,64 ,48 ) CCSRCH391J50 XV-EV500...
Page 72
C 701 (A,24 ,131 ) CKSQYB105K16 Q 5607(B,122 ,72 ) DIGITAL TR(SC-70) RT1P431M C 711 (A,28 ,73 ) CKSRYB105K10 C 712 (A,35 ,78 ) CCSRCH471J50 Q 5701(B,203 ,82 ) TRANSISTOR 2SC4081 C 713 (A,29 ,66 ) CKSQYB225K10 Q 5801(B,15 ,90 ) TRANSISTOR 2SB1132 XV-EV500...
Page 73
RS1/16S223J VR2802(A,29 ,28 ) VR PCP1032 R 2281(B,213 ,45 ) RS1/16S222J X 5501(A,69 ,193 ) CERAMIC RESONATOR ASS7034 R 2282(B,217 ,21 ) RS1/16S222J (10MHz) R 2283(B,198 ,49 ) RS1/16S472J R 2291(B,169 ,28 ) RS1/16S681J CN2301(A,42 ,43 ) CONNECTOR B4B-PH XV-EV500...
Page 74
R 5503(B,39 ,189 ) RS1/16S473J R 5593(B,66 ,189 ) RS1/16S101J R 5504(B,28 ,186 ) RS1/16S101J R 5594(B,77 ,194 ) RS1/16S221J R 5505(B,24 ,188 ) RS1/16S103J R 5595(B,57 ,194 ) RS1/16S221J R 5506(B,56 ,199 ) RS1/16S221J R 5597(B,69 ,146 ) RS1/16S221J XV-EV500...
Page 75
C 2206(B,138 ,36 ) CCSRCH101J50 R 8206(B,128 ,198 ) RS1/16S103J C 2211(B,171 ,12 ) CKSRYB152K50 R 8207(B,132 ,193 ) RS1/16S682J C 2212(B,171 ,17 ) CKSRYB152K50 R 8208(B,134 ,193 ) RS1/16S153J C 2213(B,134 ,9 ) CCSRCH101J50 R 8209(B,136 ,193 ) RS1/16S472J XV-EV500...
Page 76
C 2802(A,23 ,51 ) CQMA682J50 C 8214(B,148 ,201 ) CKSRYB224K16 C 2803(A,19 ,46 ) CQMA472J50 C 8215(B,130 ,198 ) CKSRYB224K16 C 2804(A,23 ,37 ) CQMA472J50 C 8216(B,126 ,198 ) CKSRYB472K50 C 2805(A,14 ,37 ) CEJQ330M10 C 8217(B,140 ,193 ) CKSRYB471K50 XV-EV500...
Page 77
Q 5101(B,299 ,24 ) DIGITAL TR(SC-70) RT1N431M R 5303(B,289 ,162 ) RS1/16S152J Q 5102(B,299 ,29 ) DIGITAL TR(SC-70) RT1N431M R 5304(A,325 ,5 ) RS1/16S182J Q 5110(B,263 ,20 ) DIGITAL TR(SC-70) RT1N431M R 5304(A,283 ,204 ) RS1/16S182J Q 5204(B,280 ,109 ) TRANSISTOR(SC-59) 2SC3052 XV-EV500...
Page 78
C 5402(B,304 ,71 ) CKSRYB104K25 R 5216(B,276 ,102 ) RS1/16S101J R 5217(B,274 ,105 ) RS1/16S122J C 5403(B,301 ,71 ) CCSRCH101J50 C 5404(B,306 ,71 ) CKSRYB103K50 CAPACITORS C 5405(B,308 ,67 ) CKSRYB123K50 C 5101(B,298 ,52 ) CKSRYB102K50 C 5406(B,308 ,71 ) CKSRYB472K50 XV-EV500...
Page 79
R 108 (B,101,30) RS1/16S273J D 91 (B,66,47) CHIP ZENER DIODE UDZS18B R 109 (B,114,107) RS1/16S821J > D 98 (A,78,33) DIODE MTZJ11(B) D 101 (B,141,110) DIODE MA111 R 111 (B,90,46) RS1/16S102J D 102 (B,106,94) DIODE MA111 R 112 (B,88,46) RS1/16S102J XV-EV500...
Page 80
IC 3055(B,29 ,108 ) OP-AMP IC HA17558AF R 3671(B,39,88) RS1/16S103J IC 3056(B,28 ,140 ) OP-AMP IC HA17558AF R 3672(B,37,91) RS1/16S103J IC 3062(B,56 ,60 ) ELECTRIC VOL IC 6CH BD3814FV > IC 3101(A,145 ,186 ) PROTECTOR(7A) AEK7047 R 3673(B,45,43) RS1/16S681J R 3674(B,35,40) RS1/16S681J XV-EV500...
P3 L (CN2507) P1 R (CN2507) VR2401 L ch Repeat recording, playback and REC = STD–633 test tape and record/ (IFAF ASSY) adjustment until playback level of the playback the 315Hz signal. PLAY VR2402 315Hz signal becomes –7.7dBV±0.5dB. R ch XV-EV500...
[Electrical Part] screw screw Electrical adjustments are not required. 6.2.2 JIGS AND MEASURING INSTRUMENTS Test mode remote control Screwdriver (large) Screwdriver (medium) TV monitor unit (GGF1381) Screw tight (GYL1001) DVD test disc Precise screwdriver Soldering iron (GGV1025) XV-EV500...
Exchange the Traverse Mechanism point Assy-S Electric point ∗ After adjustment, screw locks Mechanical Ÿ Exchange the Spindle Motor point with the Screw tight. Electric point Exchange PCB Assy Mechanical Exchange PC Board point LOAB and DVDM ASSYS Electric point XV-EV500...
• After going into test mode, if you play back the disc, "DISC-NON" is displayed. • The video signal and the audio signal are outputted during the test mode. • The SKIP key and the SCAN key are effective during the test mode. TEST MODE: OFF POWER GGF1381 Test mode remote control unit XV-EV500...
(Refer to "6.2.1 ADJUSTMENT ITEMS AND LOCATION".) Joint 7.5mm Mechanism base • Attach the Traverse Mechanism Assy-S to the 05 LOADER Assy. • Turn it over and attach the joint and the joint spring. • Arrange the flexible cables. (Refer to "7.1.10 DISASSEMBLY".) XV-EV500...
Page 91
90 degrees step till ERROR RATE block error rate becomes around "1E-3" again . CHP/TIM • Record the number of rotation (N1). • Fasten the tangential adjustment screw till the number of rotation becomes Service mode end harf of N1. Best tangential point XV-EV500...
: Press the [TEST] (A8-5E) and [4] (A8-04) keys in order, and turn on the laser diode (780n). 3 Release the Test mode • Turn off the power. • Press the [ESC] (A8-5F) key of the remote control unit and reset it. XV-EV500...
: [NTSC] PAL system : [PAL] Automatic setting : [AUTO] Scart terminal output [SK – ∗ ∗] (Display only the WY model which can do the output setting of scart terminal.) VIDEO : [00] S-VIDEO : [01] : [02] XV-EV500...
• Region confirmation mode (ESC + A.MON [Test mode remote control unit] + "1"-"8" [Test mode remote control unit] keys) After you press the AUDIO key while holding the ESC key pressed and then input the region number, if the number is different from that set in the unit, an error message is displayed, and the tray opens. XV-EV500...
Display it according to model information set from the FL controller. 2 Region No. 3 Part number 4 ROM version 5 Flash size 6 FL controller version 7 CHIP VERSION 9 Remote control code 0 Key code of Main unit XV-EV500...
%%e -2 : NG 7.0e -4 : NG 3 EDC/ID error history (ID Address, EDC/ID errors, last eight errors) Note: ∗ Error of AV1 is not supported in this player. Indication plan contents Character in bold : Item name : Information display XV-EV500...
Assy. Measure the voltage between the both ends of R321 or R326 on the DVDM Assy. If the voltage is 0.4 V or higher, the 780-nm LD is degraded. 05SD PICKUP ASSY CN101 DVDM ASSY Front side SIDE A XV-EV500...
An opening screen is not DVDM Assy displayed on the monitor Check the video signal path between DVD IC (DVDM Assy IC201) and Video circuit after DVD IC (The FL display lights. The video-out terminal (see the block diagram) (IC201) mechanism works.) XV-EV500...
Page 100
DVD IC (IC201) S video signal (IC401-pin 21, pin 26) Video IC (IC401, IC451) RGB video signal (IC401-pin 16, pin 18, pin 20) No sound DVDM Assy Check the waveform (SPDIF: CN901-pin 16). (Picture is normal) DVD IC (IC201) XV-EV500...
Page 101
Any kind of symptoms (no power, a failure in any of the servo, video and audio systems, etc.) may be (DVDM Assy : IC201) generated, because the DVD processing is performed by a single chip. 64M SDRAM No power. (DVDM Assy : IC202) Block noise is generated during playback. XV-EV500...
ID number. 0 0 0 0 0 0 0 0 1 Note: If you press the PLAY button before inputting a 9-digit ID <PLAY> Enter number, the unit returns to Step 2 without doing anything else. Input ID Number ! XV-EV500...
Page 103
(The STOP key is not accepted after all 9 digits have been entered.) [Player's ID Number Setting] ID Number ? 0 0 0 0 0 0 0 0 1 Compare 0 0 0 0 0 0 0 0 1 <PLAY> Enter <STOP> Memory Clear Input ID Number ! XV-EV500...
Page 104
• Indication when the data have not been set Insert The ID Data Disc ! If no ID data are set after the ID number is changed, the message "NO ID DATA" displays on FL display after the power is turned on or during Stop mode. XV-EV500...
If the tray pops out a little, fully pull it out by hand. Tweezer Slit Rear View Press the STANDBY/ON button to turn on the power. Press the 0 OPEN/CLOSE button to open the Tray. Remove the Tray Cap Assy. Set the Test Disc. Bottom View Test Disc Tray Cap Assy XV-EV500...
Page 106
If you want to power on the set with IFAF Assy removed from the Rear Panel, make sure the RCA ground is connected to the Rear Panel as shown in the attached photo. RCA Ground Front Panel Assy IFAF Assy Rear View XV-EV500...
Page 107
AMP Assy Lift up the IFAF Assy as shown in the photo above to Rear View remove the Power Amplifier Module. Remove 4 screws on the Power Amplifier Module. AMP Assy Tuner Assy Power Amplifier Assy Power Amplifier Module XV-EV500...
Page 108
Remove the IFAF Assy as in section 3 steps 1 to 3. Remove 2 screws from the DVD Module. Carefully remove the DVD Module by lifting the Front Panel Assy upward. IFAF Assy POWER Assy Caution : Be careful not to damaged the 2 DVD FFC Cable XV-EV500...
Page 109
Connect both FFC Cables onto IFAF Assy CN5102 (use GGD1309) and CN8301(use back original cable) Flip the DVD Main Board as shown in the photo. Also ensure that the RCA ground is connected to the Rear Panel. POWER Assy RCA Ground IFAF Assy DVDM Assy GGD1425 GGD1309 XV-EV500...
Page 110
Bridge 04 Note when reinserting the tray When reinserting the tray, first align the triangle printed on the loading base and the pin of the drive cam, then insert the tray. Drive cam Tray Front side Loading base Triangle XV-EV500...
Page 111
Flexible cable Dislodge the two flexible cables from their factory for the spindle motor placement. Front Side Flexible cable for the pickup Bottom view Unhook the four hooks. Traverse Mechanism Assy-S Remove the Traverse Mechanism Assy-S × 2 × 2 XV-EV500...
Page 112
Adjustment screw Adjustment screw Remove the 05SD Pickup Assy. (skew screw VK1) (skew screw VK1) 05SD Pickup Assy-S Note: Be careful not to lose the adjustment spring (skew spring VK1). Adjustment screw (skew screw VK1) Adjustment spring (skew spring VK1) XV-EV500...
Page 113
Note: The screw is secured with the silicone adhesive. Make sure to apply the silicone adhesive after reattaching the screw. Joint VK1B Joint spring VK1 Silicone Adhesive GEM1037 Arrangement of the flexible cable for the spindle motor : Conductive surface Hook Front Side Hook Bottom view XV-EV500...
Page 114
Attach the flexible cable for the pickup to the connector. Fold the flexible cable along the hook. Pass the flexible cable through the hook. Hook Backing Front Side Bottom View Hook Pass the flexible cable through the hook. Hook Hook Make sure that the cable is loose XV-EV500...
HP MUTE ON/OFF XRECMUTE REC OUTPUT MUTE ON/OFF B_MUSIC Control for LED of BASS MUSIC REAR RELAY ON/OFF RYFSC FRONT/SW/CENTER RELAY ON/OFF B_MOVIE Control for LED of BASS MOVIE TIMERLED Control TIMER LED VOCALC Control for VOCALC − VSS4 − VDD4 XV-EV500...
Page 116
Input MS signa TCEXPCLK Clock to EXPAND IC for deck TCEXPCE Chip enable to EXPAND IC for deck TCEXPDAT Data to EXPAND IC for deck INPUTSELB AUDIO INPUT SELECT B INPUTSELA AUDIO INPUT SELECT A ECHCNT1 Control for ECHO1 XV-EV500...
Page 117
Control for deck actual function XPBMUTE Control PB mute PB/XREC Switch DOLBY PB/REC RMUTE Control REC mute DOLBY Control DOLBY NR (Standby) Output tape solenoid MOTOR Output tape motor BIAS Control bias of deck XBEATCUT Control beat cut of deck XV-EV500...
• If no pulse is input to the AC terminal (Pin 4) for about 60 msec when the microcomputer is in Memory Backup mode, it will not do any processing. • The unit will recover from Memory Backup mode if a reset command is input to the XRESET terminal (Pin 8). XV-EV500...
1.83 ohms or less, Q3601 begins to operate, Q3639 is turned on, Q3640 (E, C, and B)is turned on, and the level of XPROTECT becomes MID. → The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-EV500...
Page 120
5 V. Therefore, Q101 (Q103) (E, C, B) then Q102 (Q104) (E, C, B) are turned on, the level of XPROTECT becomes low. (3) When VD+5 is short-circuited The level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-EV500...
Page 121
When the temperature at TH111 reaches 90-110_C (varying according to conditions,) the voltage at Point (A) becomes high enough to turn Q111 on, and the level of the XPROTECT line becomes low. The microcomputer detects the XPROTECT level and shuts the power to the unit off. XV-EV500...
Page 122
(2) When the VDET signal to the microcomputer is interrupted because of defective soldering of the 30-pin connector or incomplete insertion of FFC → The VDET level is lowered by the pull-down resistor (1 Mohms) on the side of the microcomputer. XV-EV500...
Page 123
Q3632 (E2, C2, B2), Q3633, and Q3636 (E, C, B) are turned on, the line to activate the power amp mute becomes low level, and the power amp mute is turned on. (2) HP MUTE Q3635 is turned on, and the MUTE circuit for HP is turned on. XV-EV500...
11 MIC VOL and MIC input jacks Controls the volume of the karaoke mics (MAIN and SUB). MIC VOL PHONES MAIN 12 PHONES jack Headphone jack. Display See Display below. Sound options FRONT SURROUND (EV700/1000 only) – Switches on the Front Surround mode. XV-EV500...
Page 125
Lights when one of the Advanced or Front Surround listening modes is selected. Karaoke indicators ECHO – Lights when the Karaoke ECHO SFC (EV500 only) effect is selected. Lights when one of the Sound Field Control listening modes is selected. XV-EV500...
Page 126
Lights during multi-angle scenes on a DVD 15 LINE REC (EV700/1000 only) (When headphones are connected, none of the Lights when the line recording mode is speaker indicators are lit.) switched on. Playback mode indicators 16 Level meter Lights during program play – XV-EV500...
Page 127
DVD control buttons ENTER , TUNE & cursor control buttons AUDIO Selects the audio channel or Navigates on-screen displays and menus. language. ENTER selects an option or executes a SUBTITLE – Selects a subtitle display. command. XV-EV500...
Page 128
INPUT – Switches the TV input MONO (SHIFT+5) – Press to listen to a CHANNEL +/– – Selects channels stereo FM broadcast in mono. VOLUME +/– – Adjusts the TV volume TIMER (SHIFT+6) – Use for setting and checking the clock and the timers. XV-EV500...
Page 129
Position to be cleaned Cleaning tools Pickup leneses Cleaning liquid : GEM1004 Cleaning paper : GED-008 Position to be cleaned Cleaning tools Cassette heads Pinch rollers Cleaning paper : GED-008 Capstans Position to be cleaned Cleaning tools Fans Cleaning paper : GED-008 XV-EV500...