Table of Contents
Advertisement
InfoCenter screen. Do not operate the machine above
low idle until after the warm-up period.
Understanding Toro Smart
Power™
With Smart Power, the operator does not have to
listen to the engine speed in heavy load conditions.
Smart Power prevents the engine from bogging
down in heavy cutting conditions by automatically
controlling the machine speed and optimizing cutting
performance.
Note:
By default, the Smart Power feature is O
Starting the Engine
Important:
You must bleed the fuel system before
starting the engine if you are starting the engine
for the first time, the engine has stopped due to
lack of fuel, or you have performed maintenance
on the fuel system; refer to
System (page
51).
1.
Sit on the seat, keep your foot off the traction
pedal so that it is in N
brake, set the throttle to the F
ensure that the PTO is not engaged.
2.
Turn the key to the O
An automatic timer controls the glow plug
preheat for 6 seconds.
3.
After preheating the glow plugs, turn the key to
the S
position.
TART
Crank the engine for no longer than 15 seconds.
Release the key when the engine starts. If
additional preheating is required, turn the key to
the O
position and then to the O
FF
position. Repeat this process as required.
4.
Run the engine at low idle speed until it warms
up.
Shutting Off the Engine
1.
Move all controls to N
parking brake, move the throttle to the low idle
position and allow the engine to reach low idle
speed.
Important:
Allow the engine to idle for 5
minutes before shutting it off after a full load
operation. Failure to do so may damage
engine components.
2.
Turn the key to the O
from the switch.
N
Bleeding the Fuel
, engage the parking
EUTRAL
position, and
AST
/P
position.
N
REHEAT
/P
N
REHEAT
, engage the
EUTRAL
position and remove it
FF
Cutting Grass with the
Machine
1.
Disengage the parking brake, disengage the
PTO, and raise the cutting units.
2.
Move the throttle to the F
3.
Drive the machine to the mowing area.
4.
Park the machine approximately 6 m (20 feet)
off the fairway, facing the intended mowing
direction.
5.
Lower the cutting units completely with the
lift/lower control lever.
.
6.
Engage the PTO.
Note:
The cutting units will not start.
7.
Tap the lift/lower control lever rearward to lift the
cutting units to the turnaround position.
Note:
Tapping the lift/lower control lever
without holding it raises the cutting units to the
turnaround position and stops the rotation of the
reels until the cutting units are lowered.
8.
Using the traction pedal, approach the mowing
area slowly.
9.
Once you reach the edge of the mowing area
to start mowing, lower the cutting units with the
lift/lower control lever.
Note:
Practice to ensure the cutting units do
not lower early or mow an unintended area.
10.
Complete the mowing pass.
11.
When nearing the opposite edge of the fairway
(prior to reaching the edge of the mowing area),
tap the lift/lower control lever rearward to lift the
cutting units to the turnaround position.
12.
Perform a tear-shaped turn to quickly line up for
your next pass.
13.
Press the lift/lower control lever to automatically
lower the cutting units from the turnaround
position and continue mowing.
14.
After mowing the desired area, follow the
perimeter of the area to complete the cleanup
mow pass. This will ensure that all of the turf
along the edge of the fairway where the cutting
units were being lifted and lowered is uniformly
cut.
Note:
It is recommended to use the Virtual
Pedal Stop (VPS) to temporarily set a lower
max speed to improve operating control while
completing the cleanup pass; refer to
Virtual Pedal Stop (VPS) Feature (page
33
position.
AST
Using the
31).
Advertisement
Table of Contents
