Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
9
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
9
dangerous and will invalidate the warranty.
Ensure the drill is switched off before installing the battery pack.
9
Keep the drill and charger clean for best and safest performance.
9
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
9
Evaluate your working area before using the drill; e.g. ceilings, floors and enclosures may contain electrical items or water piping
9
Ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
9
Secure loose work pieces with a clamp, vice or other adequate holding device.
9
Avoid unintentional starting.
9
Wear approved safety eye protection (standard spectacles are not adequate).
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
9
Be aware that this drill does not need to be plugged into the mains power.
9
Keep chuck direction switch in the locked position until the drill is required for use.
9
Keep children and unauthorised persons away from the working area.
9
DO NOT use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
8
DO NOT allow children to operate the drill.
8
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
8
DO NOT hold unsecured work piece in your hand.
8
DO NOT leave the drill operating unattended.
8
DO NOT carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
8
DO NOT use the drill for a task it is not designed to perform.
8
DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT get the drill or battery charger wet or use in damp or wet locations.
8
2. INTRODUCTION
Compact, lightweight cordless drill/driver with added hammer function. Comfortable composite housing with soft grip to reduce vibration. Ø0.8-
10mm Keyless chuck. Two speed settings and 21 torque settings provide the control required to complete various tasks. Integral LED battery
level indicator and LED work light. Supplied with belt hook for safer storage while not in use. Requires Model No. CP1200BP 12V 1.5Ah
Lithium-ion Battery and Model No. CP1200MC Battery Charger.
3. SPECIFICATION
Model no ................................................................... CP1201
Battery options .......................................................................
12V 1.5Ah Li-ion, 12V 3Ah Li-ion, 12V 4Ah Li-ion (not included)
Chuck size ................................................................ Ø10mm
Consumable parts ..................................................................
CP1200BP - Battery 12V 1.5Ah, CP1200BP3 - Battery 12V 3Ah,
CP1200BP4 - Battery 12V 4Ah (not included)
Impact rate ............................................. 0-6000/0-19500bpm
No load speed .............................................0-400/0-1300rpm
Noise power/pressure .......................................... 80/69dB(A)
Vibration/uncertainty ............................................ 9.6/1.5m/s²
Replacement parts ....................... CP1200MC Mains charger
3.0.1.
© Jack Sealey Limited
Ø10MM 12V CORDLESS HAMMER DRILL/
DRIVER - BODY ONLY
MODEL NO:
Wear protective
Wear ear
gloves
protection
Original Language Version
CP1201
Wear a mask
fig.1
CP1201 | Issue:3(SP) 11/05/20
Advertisement
Related Manuals for Sealey CP1201
Summary of Contents for Sealey CP1201
- Page 1 CP1201 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 01284 703534 sales@sealey.co.uk...