Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used
according to these instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND
CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO
MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
1.1
GENERAL SAFETY
Disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.
3
Maintain the drill and battery in good condition. Check moving parts alignment on a regular basis.
3
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Unauthorised parts may be
3
dangerous and will invalidate the warranty.
Ensure the drill is switched off before installing the battery pack.
3
Keep the drill and charger clean for best and safest performance.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Evaluate your working area before using the drill e.g. ceiling, floors and enclosures may contain electrical items or water piping.
3
Ensure battery pack is correctly inserted into the drill handle and latched in place before attempting to switch on drill.
3
Secure loose workpieces with a clamp, vice or other adequate holding device.
3
Avoid unintentional starting.
3
Wear approved safety eye protection (standard spectacles are not adequate).
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
3
Be aware that this drill does not need to be plugged into the mains power.
3
Keep chuck direction switch in the locked position until the drill is required for use.
3
Keep children and unauthorised persons away from the working area.
3
DO NOT use the drill where there are flammable liquids, solids or gases, such as paint solvents, etc.
7
DO NOT allow children to operate the drill.
7
DO NOT operate the drill if any parts are missing as this may cause failure and/or personal injury.
7
DO NOT hold unsecured workpiece in your hand.
7
DO NOT leave the drill operating unattended.
7
DO NOT carry the drill with your finger on the power switch. Keep chuck direction switch in the locked position.
7
DO NOT use the drill for a task it is not designed to perform.
7
DO NOT operate the drill when you are tired or under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT get the drill or battery charger wet or use in damp or wet locations.
7
Keep drill and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104°F (40°C).
3
1.2
BATTERY SAFETY INSTRUCTIONS.
WARNING! Battery contains nickel-cadmium which is dangerous. Handle with care to avoid damage, fire, corrosion or personal injury.
p
Charge battery prior to first use. The battery pack will have been shipped in a low charge state.
3
Use only the charger provided to charge the drill battery.
3
DO NOT charge battery when room temperature is below 50°F (10°C) or above 104°F (40°C).
7
DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
7
DO NOT short-circuit the battery by linking both terminals with a metal object, or your fingers etc.
7
DO NOT store the battery (or drill) in locations where the temperature may exceed 104°F (40°C) such as outside sheds, above
7
heaters, or metal buildings in summer.
WARNING! Dispose of spent batteries correctly as they contain nickel-cadmium. DANGER! DO NOT attempt to disassemble the
p
battery pack. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle
according to local authority regulations.
WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
p
immediate action:
p a) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
p b) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
1.3
ELECTRICAL SAFETY.
REGARDING DIRECT MAINS POWER USE WITH THE CHARGER.
WARNING! It is the owner’s responsibility to read, understand and comply with the following electrical instructions:
p
p
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current
Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD (Residual Current Device) is
used with all electrical products, particularly portable equipment which is plugged into an electrical supply not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.3.1 The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2 The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
CORDLESS DRILL/DRIVER
18V - 1HR CHARGE
MODEL:
INSTRUCTIONS FOR:
CP1801V
CP1801V - 1 - 060105
Advertisement
Related Manuals for Sealey CP1801V
Summary of Contents for Sealey CP1801V
-
Page 1: Safety Instructions
CP1801V MODEL: Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS, AND CAUTIONS. -
Page 2: Operating Instructions
5. The speed of the drill is controlled by the electronic variable speed switch. After moving direction switch to ‘forward’ (or ‘reverse’) press the speed switch gently for a slow speed and progressively increase the pressure on the switch to produce correspondingly higher speeds (try before starting to drill). CP1801V - 1 - 060105... -
Page 3: Parts List
The construction files for these products are held by the Manufacturer and may be inspected, CHARGER For Jack Sealey Ltd. by a national authority, upon request to Jack Sealey Ltd. Models: CP1801V, CP1801VC Sole importer into the UK Signed by Mark Sweetman...