Pioneer DEH-1800 Installation Manual
Pioneer deh-1800: user guide
Hide thumbs
Also See for DEH-1800:
- Operation manual (37 pages) ,
- Service manual (4 pages) ,
- Operation manual (22 pages)
Advertisement
Available languages
Available languages
DEH-2800MP
DEH-1800
This product conforms to CEMA cord colors.
Le code de couleur des câbles utilisé pour ce produit est
conforme à CEMA.
Los colores de los cables este producto se conforman
con el código de colores CEMA.
Printed in Thailand
Imprimé en Thaïlande
<CRD4028-A/N> UC
<KSNZX> <05G00000>
Connecting the Units
Note:
• This unit is for vehicles with a 12-volt battery and
• When this product's source is switched ON, a con-
negative grounding. Before installing it in a recre-
trol signal is output through the blue/white lead.
ational vehicle, truck or bus, check the battery
Connect to an external power amp's system remote
voltage.
control or the car's Auto-antenna relay control ter-
• To avoid shorts in the electrical system, be sure to
minal (max. 300 mA 12 V DC). If the car features
disconnect the ≠ battery cable before beginning
a glass antenna, connect to the antenna booster
installation.
power supply terminal.
• Refer to the owner's manual for details on con-
• When an external power amp is being used with
necting the power amp and other units, then make
this system, be sure not to connect the blue/white
connections correctly.
lead to the amp's power terminal. Likewise, do not
• Secure the wiring with cable clamps or adhesive
connect the blue/white lead to the power terminal
tape. To protect the wiring, wrap adhesive tape
of the auto-antenna. Such connection could cause
around them where they lie against metal parts.
excessive current drain and malfunction.
• Route and secure all wiring so it cannot touch any
• To avoid a short-circuit, cover the disconnected
moving parts, such as the gear shift, handbrake and
lead with insulating tape. Insulate the unused
seat rails. Do not route wiring in places that get
speaker leads without fail. There is a possibility of
hot, such as near the heater outlet. If the insulation
a short-circuit if the leads are not insulated.
of the wiring melts or gets torn, there is a danger of
• If this unit is installed in a vehicle that does not
the wiring short-circuiting to the vehicle body.
have an ACC (accessory) position on the ignition
• Don't pass the yellow lead through a hole into the
switch, the red lead of the unit should be connected
engine compartment to connect to the battery. This
to a terminal coupled with ignition switch ON/OFF
will damage the lead insulation and cause a very
operations. If this is not done, the vehicle battery
dangerous short.
may be drained when you are away from the vehi-
• Do not shorten any leads. If you do, the protection
cle for several hours. (Fig. 1)
circuit may fail to work when it should.
• Never feed power to other equipment by cutting
the insulation of the power supply lead of the unit
and tapping into the lead. The current capacity of
the lead will be exceeded, causing overheating.
• When replacing the fuse, be sure to only use a fuse
of the rating prescribed on this unit.
• Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
ACC position
No ACC position
the left and right ≠ speaker leads are common.
If you ground the products together and the ground
becomes detached, there is a risk of damage to the
products or fire.
• The black lead is ground. Please ground this lead
• Cords for this product and those for other prod-
separately from the ground of high-current prod-
ucts may be different colors even if they have the
ucts such as power amps.
same function. When connecting this product to
If you ground the products together and the ground
another product, refer to the supplied manuals of
becomes detached, there is a risk of damage to the
both products and connect cords that have the
products or fire.
same function.
• Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with out-
put and/or impedance values other than those
noted here may result in the speakers catching fire,
emitting smoke, or becoming damaged.
This Product
Rear output
Antenna jack
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
Red
To electric terminal controlled
by ignition switch (12 V DC)
ON/OFF.
Fig. 1
Black (ground)
To vehicle (metal) body.
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
Perform these connections when using
the optional amplifier.
Connecting cords
with RCA pin plugs
Fuse (10 A)
(sold separately)
Blue/white
To system control terminal of the power amp
or Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
System remote control
White
Gray
+
Front speaker
≠
White/black
Gray/black
Left
Green
Violet
+
Rear speaker
≠
Green/black
Violet/black
+
Rear speaker
≠
<ENGLISH>
Power amp
(sold separately)
+
Front speaker
≠
Right
+
Rear speaker
≠
+
Rear speaker
≠
Fig. 2
Advertisement
Table of Contents
Related Manuals for Pioneer DEH-1800
Summary of Contents for Pioneer DEH-1800
- Page 1 Do not route wiring in places that get DEH-1800 hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body.
-
Page 2: Raccordements Des Appareils
Raccordements des appareils Remarque: • Cet appareil est destiné aux véhicules avec une bat- • Les haut-parleurs connectés à cet appareil doivent terie de 12 V, avec pôle négatif à la masse. Avant de être en mesure de supporter une puissance de 50 W, l’installer dans un véhicule de loisir, un camion ou et doivent présenter une impédance comprise entre 4 un car, vérifier la tension de la batterie. -
Page 3: Conexión De Las Unidades
Conexión de las unidades Nota: • Esta unidad es para vehículos con batería de 12 • Los altavoces conectados a esta unidad deben ser voltios y con conexión a tierra. Antes de instalar la del tipo de alta potencia con un régimen mínimo unidad en un vehículo recreativo, camioneta, o de 50 W y una impedancia de 4 a 8 ohmios. -
Page 4: Installation
Installation Note: Removing the Unit (Fig. 5) (Fig. 6) • Before making a final installation of the unit, tem- • If installation angle exceeds 60° from horizontal, porarily connect the wiring to confirm that the con- the unit might not give its optimum performance. nections are correct and the system works proper- (Fig. -
Page 5: Montage Din Avant/Arrière
Installation Remarque: Dépose de l’unite (Fig. 5) (Fig. 6) • Avant d’effectuer l’installation définitive, reliez • L’angle de l’installation, ne doit pas dépasser 60° provisoirement les appareils entre eux pour vous par rapport à l’horizontale, faute de quoi l’unité ne assurer qu’ils fonctionnent correctement, individu- fournira pas ses performances optimales. -
Page 6: Instalación
Instalación Nota: Quitado de la unidad (Fig. 5) (Fig. 6) • Antes de finalmente instalar la unidad, conecte el • Si el ángulo de la instalación excede los 60° del cableado temporalmente y compruebe que las lado horizontal, la unidad podría no brindar su conexiones están correctas e que el sistema fun- óptimo funcionamiento.