Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment, make sure you know where the nearest fire extinguisher is.
WARNING! Always wear approved eye/ face protection when operating the torch.
‰
WARNING! DO NOT use the torch if you notice that it is damaged or if there could be a gas leak from it.
‰
WARNING! Butane gas is extremely flammable, handle with care.
‰
WARNING! Always point the torch away from the eyes and body when igniting and during operation.
‰
WARNING! DO NOT put the torch down when it is lit, DO NOT leave it unattended.
‰
WARNING! The flame is not easily visible in bright daylight.
‰
WARNING! Ensure the flame is completely extinguished after use. DO NOT use water to cool the torch down.
‰
WARNING! Only use in a well ventilated area.
‰
DO NOT use the torch in an area where paint fumes, solvents or other flammable solids, liquids or gases pose a potential hazard.
8
Keep flammable material away from the torch when operating.
DO NOT operate the torch when you are tired or under the influence of alcohol, drugs or intoxicating medication.
8
DO NOT hold any workpiece by hand.
8
DO NOT touch the workpiece close to the heated area as it will be very hot. Allow to cool.
8
DO NOT operate the torch if it is damaged as this may cause failure and/or possible personal injury.
8
DO NOT touch the top of the torch during or immediately after use, as it will be very hot. Allow to cool.
8
DO NOT allow children to operate the torch.
8
After use, allow the torch to cool before storing it.
9
When not in use, store away from direct sunlight in a safe, dry, childproof location.
9
DO NOT store at over 40°C, such as in a car in hot weather.
8
DO NOT modify the appliance.
8
When filled, it will contain flammable gas under pressure.
9
DO NOT puncture or put in fire.
8
Make sure the fire is off before refilling.
9
DO NOT keep lit for more than 5 minutes.
8
Allow the micro torch to cool down before storage. Storing the appliance in well ventilated area and ensure the flame is over after the
9
operation.
Use only Sealey original spare parts.
9
DO NOT use torch as a cigarette lighter.
8
Be extra careful when using the torch outdoors on sunny or windy days. Wind may carry the torch's heat back toward you or other
9
areas which are not intended to be heated.
Always check to make sure no unintended parts or materials are being heated.
9
Whenever there is a possibility that unintended material has been heated, wait at least two hours before leaving the area.
9
DO NOT inhale soldering fumes.
8
Follow refilling procedure to avoid serious accidents.
9
2. INTRODUCTION
One of a comprehensive range of Premier Hand Tools, suitable for daily professional use. 3-in-1 device that can be used for heating, soldering
and shrinking. Fitted with indexing head for three different positions as well as magnetic stand. Powered by butane (lighter fuel) and features
a piezoelectric ignition switch. Viewing window at bottom of device to monitor fuel. Flame temperature 1300°C, soldering temperature 450°C
and hot air temperature 600°C (Approximately). 60-75 Minute run time with 30ml fuel capacity. Kit Includes; soldering iron, chisel tip, anvil tip,
needle tip, hot knife, deflector nozzle, lead free solder, cleansing sponge and tip holder.
3. SPECIFICATION
Model No: ................................................................. AK2971
Temperature range: . ............................................ 450-1300
© Jack Sealey Limited
BUTANE INDEXING SOLDERING IRON KIT
3-IN-1
MODEL NO:
Wear protective
Hot surfaces
gloves
C
o
Original Language Version
AK2971
AK2971 Issue 1 04/01/2023
Advertisement
Related Manuals for Sealey AK2971
Summary of Contents for Sealey AK2971
- Page 1 AK2971 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Clean the tip on the sponge when it is still warm. ENVIRONMENT PROTECTION Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. Important: No Liability is accepted for incorrect use of this product. Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. REGISTER YOUR PURCHASE HERE Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR 01284 757500 sales@sealey.co.uk www.sealey.co.uk AK2971 Issue 1 04/01/2023 Original Language Version © Jack Sealey Limited...