Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS.
USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE
DAMAGE AND/OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1.
ELECTRICAL SAFETY
WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and any other
connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of appropriate safety devices.
A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. we also recommend that a residual current
device (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected
by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the Electricity at work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all connections to ensure that none is loose.
1.1.6. Important: Ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOT pull or carry the appliance by the power cable.
1.1.8. DO NOT pull the plug from the socket by the cable.
1.1.9. DO NOT use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. when a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) connect the grEEn/YELLow earth wire to the earth terminal 'E'.
b) connect the Brown live wire to the live terminal 'L'.
c) connect the BLuE neutral wire to the neutral terminal 'n'.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the
restraint is tight.
double insulated products, which are always marked with this symbol
to rewire, connect the wires as indicated above - do not connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. we recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1.2.
GENERAL SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this equipment.
familiarise yourself with the application, limitations and potential hazards of the soldering iron.
replace or repair damaged parts. Use genuine parts only. Non-authorised parts may be dangerous and will invalidate the warranty.
Locate in a suitable work area, keep the work area clean and tidy, and free from unrelated materials. Ensure there is adequate lighting.
Keep the soldering iron clean for best and safest performance.
Ensure there are no flammable or combustible materials near the work area.
wear approved safety eye protection (standard spectacles are not adequate).
wear appropriate protective clothing.
remove ill fitting clothing, ties, watches, rings and other loose jewellery and contain long hair.
Ensure the workpiece is adequately held before operating the soldering iron.
Always use the stand provided for the soldering iron, so that the tip cannot make contact with the work surface.
Ensure that when the soldering iron is put down during use, that the tip is not near to, or in contact with any material that may burn or melt,
including the products own supply lead.
remove excess solder from the soldering iron by wiping the tip on a damp sponge.
DO NOT attempt to remove excess solder from the soldering iron by shaking it, as hot solder may become airborne and land on skin
causing burns and blisters.
DO NOT allow children or pets into the area where the soldering is taking place.
DO NOT attempt to cool the soldering iron with water.
WARNING! disconnect the soldering iron from the mains supply and allow it to cool before changing tips.
DO NOT operate the soldering iron when you are tired, under the influence of alcohol, drugs or intoxicating medication.
DO NOT leave a hot soldering iron unattended.- If leaving the work area, even for a short period of time, switch it off and allow to cool.
DO NOT use the soldering iron for any purpose other than that for which they have been designed.
I n s t r u c t I o n s f o r :
ProfEssIonAL soLdErIng Iron
- duAL wAttAgE
ModEL no's
, are fitted with live (brown) and neutral (blue) wires only.
Original Language Version
: SD1530, SD4080
Yellow & Green
Earth Wire
Blue
Neutral
Wire
FUSE RATING: 3 AMP
sd1530 & sd4080
Brown
Live
Wire
Cable
Restraint
Issue: 1 - 13/04/10
Advertisement
Related Manuals for Sealey SD1530
Summary of Contents for Sealey SD1530
- Page 1 (rcd) is used. It is particularly important to use an rcd with portable products that are plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual current device by contacting your sealey dealer.
- Page 2 Insert the new tip and twist it into the orientation you require. Lock the tip in place by tightening the retaining screw (fig.2). sealey Part no's for replacement tips: Model no. sd1530 - SD1530/T, Model no. sd4080 - SD4080/T.