Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for DeWalt DWE4000-XE
Summary of Contents for DeWalt DWE4000-XE
- Page 1 DWE4000-XE DWE4001-XE...
- Page 2 English (original instructions) Copyright D Copyright D WALT WALT...
- Page 3 Fig. A DWE4001-XE Fig. B...
- Page 4 Fig. C Fig. D Fig. E Fig. E1 Fig. E2 Fig. G Fig. H...
-
Page 5: Technical Data
English SMALL ANGLE GRINDER DWE4000-XE, DWE4001-XE Congratulations! Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain You have chosen a D WALT tool. Years of experience, thorough the tool and the accessories, keep the hands warm (relevant... -
Page 6: Personal Safety
English 4) Power Tool Use and Care Unmodified plugs and matching outlets will reduce risk of electric shock. a ) Do not force the power tool. Use the correct power b ) Avoid body contact with earthed or grounded tool for your application. The correct power tool surfaces, such as pipes, radiators, ranges and will do the job better and safer at the rate for which it refrigerators. -
Page 7: Causes And Operator Prevention Of Kickback
English m ) Do not run the power tool while carrying it at your be attached to your power tool, it does not assure safe operation. side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body. d ) The rated speed of the accessory must be at least equal to the maximum speed marked on the power n ) Regularly clean the power tool’s air vents. -
Page 8: Residual Risks
English otherwise kickback may occur. Investigate and take Corners, sharp edges or bouncing have a tendency to corrective action to eliminate the cause of wheel binding. snag the rotating accessory and cause loss of control or kickback. d ) Do not restart the cutting operation in the workpiece. - Page 9 English Description (Fig. A) This tool is double insulated, therefore no earth wire is required. Always check that the power supply WARNING: Never modify the power tool or any part of it. corresponds to the voltage on the rating plate. Damage or personal injury could result.
- Page 10 English the correct guard from your local dealer or authorized 3. Press the guard 6 down and rotate it to the service centre. required position. nOTE: Edge grinding and cutting can be performed with Type 4. Securely tighten the screw 12 27 wheels designed and specified for this purpose; 6.35 mm 5.
-
Page 11: Prior To Operation
English Mounting Wire Cup Brushes and Wire Wheels wheel breakage and wheel contact. See the Accessory Chart for more information. (Fig. A) 1. Place the tool on a table, guard up. WARNING: Failure to properly seat the flange/ clamp nut/ 2. Install the backing flange 4 ... - Page 12 English On/Off Toggle Switch (Fig. G) WARNING: • Ensure all materials to be ground or cut are secured WARNING: Before using the tool, check that the handle is in place. tightened securely. • Secure and support the workpiece. Use clamps or a To run the tool press the switch 7 ...
-
Page 13: Cutting Metal
English Edge Grinding and Cutting ‑ If sanding with a backing pad, move the tool constantly in a straight line to prevent burning and swirling of WARNING: Do not use edge grinding/cutting wheels for work surface. surface grinding applications because these wheels are nOTE: Allowing the tool to rest on the work surface without not designed for side pressures encountered with surface moving will damage the work piece. -
Page 14: Maintenance
English WARNING: Never use solvents or other harsh chemicals The machine must always work in an upgrinding motion. Otherwise, the danger exists of it being pushed uncontrolled for cleaning the non‑metallic parts of the tool. These out of the cut. chemicals may weaken the materials used in these parts. Use a cloth dampened only with water and mild soap. - Page 15 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Depressed centre grinding disc Type 27 Type 27 guard Guard Backing flange Flap wheel Type 27 depressed centre wheel Wire wheels Threaded locking flange Type 27 guard Wire wheels with threaded nut Wire wheel Wire cup with...
- Page 16 English Grinding and Cutting Accessory Chart guard Type Accessory Description how to Fit grinder Masonry cutting disc, bonded Type 1 Type 1 guard Guard Metal cutting disc, bonded Backing flange Type 1 Guard Cutting wheel Diamond cutting wheels Threaded locking flange Type 27 Guard...
- Page 20 Belgique et www.dewalt.be WALT - Belgium BVBA Tel: NL 32 15 47 37 63 luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS) Tel: 70 20 15 10 www.dewalt.dk Roskildevej 22 Fax: 70 22 49 10 kundeservice.dk@sbdinc.com 2620 Albertslund Deutschland www.dewalt.de...