Anomaly Reporting; Software Support Information - HP 8340B Manual
Synthesized sweepers
Hide thumbs
Also See for 8340B:
- Manual (530 pages) ,
- Operating instructions manual (119 pages) ,
- Operating manual (14 pages)
Table of Contents
Advertisement
1.4
Make
a
Copy
Before Use
Before
running
the test software or making
any changes to the
software's configuration,
you
should make
a
copy of the master disc supplied with
this
documentation The master
should
then be stored
in
a
safe place
and the copy used for daily testing,
In
order
to
make
a
copy of the master
disc, you
will
need either two double sided 3-5"
microfloppy disc drives or one fixed disc drive and one double sided 3.5" microfloppy disc
drive-
Two
disc drives which
may
be used are the
HP
91331-1
or the HP 9122D.
In
addition, the
media
on which the copy
is
made
must be capable of storing the entire
software (Ie.,
either
another double
sided
3.5
inch
floppy or
a
fixed disc). The storage
space requirements
for
this
revision of
software
is
approximately
650
kbytes,
When copying
the software onto another 3.5 inch, double sided microfloppy, you must
first
Initialize
your
blank floppy.
When
initializing your floppy, you must
specify the interleave factor
and also the
format
to be
used during
initialization.
The required interleave factor
is 2
and the
required format
Is 3
(1024 bytes/sector) The
initialize
command you
would execute from your
computer's keyboard
is
as follows:
INITIALIZE "Address of the disc drive containing your blank floppy",2,3
An
example would
be:
INITIALIZE
":,700,1",2,3.
This
would
Initialize
a
disc at
HP-IB address
700, drive
1
and would set the disc's Interleave factor to
2
and format to 1024 bytes/sector.
If
you do not Initialize your blank 3.5
inch,
double
sided microfloppy
in
this
manner, you
will
not
have
sufficient
space on the
disc to
copy
the
software!
For your
convenience,
a
copy program has been included on the master disc supplied
with
this
document
This
program allows
you to
copy the
files
on
the
master disc to either
an
Initialized fixed disc or another
35"
double sided
floppy
When copying the master
to
another
3.5"
floppy, insert
the
master disc
Into drive
0
of your double sided
3
5"
disc drive and insert
an Initialized
35"
floppy
into
drive
1
The name of the copy program
is
"Copy"
After your
floppy has
been initialized,
load the copy program
"Copy"
from the
master disc
and
respond
to the prompts provided
To
ensure that you do not erase the programs on
the
master
disc,
you should Write
Protect the master.
1.5
Anomaly Reporting
As with
all
software,
an anomaly
may occur. Notify the nearest Hewlett-Packard sales and
service office when
a
software
anomaly
is
observed. Use the software notification form
located
at the end
of this manual.
1.6
Software Support Information
The software
support provided
by
Hewlett-Packard
for the HP
8340A/B
and HP
8341A/B
Attenuator Calibration and Operation Verification
Test Software, HP P/N 08340-10009,
is
limited to
the correction of anomalies found
while using this test
software
with the
test
equip¬
ment recommended
in
Chapter
2
of this document, Any
deviation from the equipment recom¬
mended
in
Chapter
2
will not
be supported by Hewlett-Packard
In
addition, the
software
modifications which the operator
Is
allowed
to
perform
is
limited to the mass
storage address,
data storage address,
and
the test
equipment address modifications described
in
Chapter
3
of this
document. Modifications made
to the
software beyond those described
in
Chapter
3
will not
be supported by Hewlett-Packard.
2
General Information
HP
8340A/B
and HP
8341A/B
Advertisement
Chapters
Table of Contents
