Table of Contents
Advertisement
Quick Links
Cisco 600W Redundant Power System
Quick Start Guide with License and Warranty Information
1
Cisco 90-Day Limited Hardware Warranty Terms
2
Documents, Equipment, and Tools
3
Install the Chassis
4
Connect Cables
5
Power Up the Equipment
6
Obtaining Documentation
7
Obtaining Technical Assistance
8
Obtaining Additional Publications and Information
Quick Start Guide
Advertisement
Table of Contents
Related Manuals for Cisco 600W
Summary of Contents for Cisco 600W
- Page 1 Cisco 600W Redundant Power System Quick Start Guide with License and Warranty Information Cisco 90-Day Limited Hardware Warranty Terms Documents, Equipment, and Tools Install the Chassis Connect Cables Power Up the Equipment Obtaining Documentation Obtaining Technical Assistance Obtaining Additional Publications and Information...
-
Page 2: Cisco 90-Day Limited Hardware Warranty Terms
Cisco 90-Day Limited Hardware Warranty Terms There are special terms applicable to your hardware warranty and various services that you can use during the warranty period. Your formal Warranty Statement, including the warranty applicable to Cisco software, is included on the CD that accompanies your Cisco product. -
Page 3: User Documentation
Cisco RPS. You can access this document at Cisco Product Documentation > Access Servers and Access Routers > Cisco 600W Redundant Power System > Regulatory Compliance and Safety Information. Hardware Installation Guide A hardware installation guide provides specifications and additional instructions for installing and connecting the Cisco RPS. -
Page 4: Items Not Included
Cisco RPS. You can access these document sat Cisco Product Documentation > Access Servers and Access Routers > Cisco 600W Redundant Power System > Procedures for Spare Parts: Adapter Plates and Rack Brackets. Release Notes Release notes for the Cisco RPS provide information about the use of the Cisco RPS with various switches, hubs, and repeaters. -
Page 5: Install The Chassis
Install the Chassis Safety Information For safety information you need to know before working on your Cisco RPS, see the Regulatory Compliance and Safety Information document that accompanied this device. Chassis Installation Methods Warning Only trained and qualified personnel should be allowed to install or replace this equipment. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. -
Page 6: Attaching Brackets
Figure 2 Brackets for Telco Rack-Mounting Attaching Brackets Attach the mounting brackets to the chassis as shown in Figure 3, Figure 4, or Figure 5, using the screws provided in the bracket kit. Use a number 2 Phillips screwdriver to install the bracket screws. Figure 3 Bracket Attachment for 19-, 23-, or 24-Inch Rack with Front Panel Forward DC STATUS... -
Page 7: Connect Cables
The Cisco RPS is power-factor-corrected to comply with certain International Electrotechnical Commission (IEC) Caution standards. Do not connect the Cisco RPS to an uninterruptible power supply (UPS) that has not been tested and designed for power-factor-corrected power systems. Do not connect the Cisco RPS to a ferro-resonant transformer. - Page 8 Table 1 RPS Interface Modules Powered Device Cisco 2500 series, Cisco MC3810 Cisco 2600 series Cisco 3620 Cisco 3640 Cisco 3725 Cisco 4000 series Connection Methods and Cables Table 2 summarizes the redundancy options and cable requirements for the various external devices that can be supported by the Cisco RPS.
- Page 9 • Fully redundant—Figure 7. The power source is fully redundant because there are two AC input modules and two DC output power modules connected to each external device. If any power module fails, there is a full backup. Note This configuration is not supported for switches and hubs. •...
-
Page 10: Cable Connection Procedures
Figure 8 Redundant-with-Reboot Configuration Cisco RPS DC output AC power cords AC power strip Figure 9 Mixed Configuration Cisco RPS DC output Fully redundant Cable Connection Procedures Before connecting to external devices, read the power warnings below. Cisco recommends that you disconnect all power before beginning. - Page 11 Warning Attach only the Cisco RPS (model PWR600-AC-RPS) to the RPS receptacle. To see translations of the warnings that appear in this publication, refer to the Regulatory Compliance and Safety Information document that accompanied this device. Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.
- Page 12 SEE MANUAL BEFORE SERIAL INSTALLA TION ETHERN ET 1 ETHERN ET 0 ETHERN ET 1 ETH 1 2.0A/1.0A 50-60HZ DC INPUTS FOR REMOTE POWER SUPPLY SPECIFIE D IN MANUAL. @24A, +12V @1.0A DC INPUT Cisco RPS AC power connector connector...
- Page 13 Connect the DC-input end of the cable to a Cisco RPS rear-panel connector as shown in Figure 14 or Figure 15. Step 3 Figure 14 Connecting a One-to-One Cable to a Cisco RPS for Quasi-Redundant Power DC OUTP UT 1 AC INPU T 1 AC INPU T 2 100-2 00 V~ 50/60 Hz...
-
Page 14: Power Up The Equipment
Obtaining Documentation Cisco provides several ways to obtain documentation, technical assistance, and other technical resources. These sections explain how to obtain technical information from Cisco Systems. Cisco.com You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com/univercd/home/home.htm... -
Page 15: Obtaining Technical Assistance
• Registered Cisco.com users can order the Documentation CD-ROM (Customer Order Number DOC-CONDOCCD=) through the online Subscription Store: http://www.cisco.com/go/subscription • Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, U.S.A.) at 408 526-7208 or, elsewhere in North America, by calling 800 553-NETS (6387). -
Page 16: Technical Assistance Center
• Resolve technical issues with online support • Download and test software packages • Order Cisco learning materials and merchandise • Register for online skill assessment, training, and certification programs To obtain customized information and service, you can self-register on Cisco.com at this URL: http://www.cisco.com Technical Assistance Center The Cisco TAC is available to all customers who need technical assistance with a Cisco product, technology, or solution. -
Page 17: Obtaining Additional Publications And Information
Information about Cisco products, technologies, and network solutions is available from various online and printed sources. • The Cisco Product Catalog describes the networking products offered by Cisco Systems as well as ordering and customer support services. Access the Cisco Product Catalog at this URL: http://www.cisco.com/en/US/products/products_catalog_links_launch.html... - Page 20 Slovenia • South Africa • Spain • Sweden • Switzerland • Taiwan • Thailand • Turkey • Ukraine • United Kingdom • United States • Venezuela • Vietnam • Zimbabwe CCVP, the Cisco logo, and Welcome to the Human Network are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar,...