Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard this article will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND
CAUTIONS. USE THIS PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY
CAUSE DAMAGE OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. PLEASE KEEP INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY INSTRUCTIONS
1.1.
GENERAL SAFETY
! Follow all workshop safety rules, regulations, and conditions when using wrench.
Remove the battery pack from the wrench before servicing or performing any maintenance.
!
Maintain the wrench and battery pack in good condition. Check moving parts for alignment on a regular basis.
!
Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Non-authorised parts may be dangerous
!
and will invalidate the warranty.
Ensure the wrench is in ‘neutral’ before installing the battery pack.
!
Keep the wrench, battery pack and charger clean for optimum performance.
!
Keep work area clean and tidy and free from unrelated materials and ensure there is adequate lighting.
!
Ensure battery pack is correctly inserted into the wrench handle and latched in place before attempting to switch on wrench.
!
F WARNING! Due to the possible presence of asbestos dust from brake linings, when working around vehicle brake systems we recommend you
wear suitable respiratory protection.
! Only use impact sockets which are specifically designed for use with an impact wrench.
Avoid unintentional starting.
!
! Wear approved safety eye/face shield, ear defenders, and hand protection.
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
!
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
!
Keep children and unauthorised persons away from the working area.
!
DO NOT operate the wrench if any parts are missing as this may cause failure and/or personal injury.
%
% DO NOT use wrench unless you have been instructed in its use by a qualified person.
DO NOT operate the wrench where there are solvent fumes, flammable gases, liquids or solids.
%
DO NOT leave the wrench operating whilst unattended.
%
DO NOT carry wrench with your finger on trigger. Keep direction switch in neutral position when not in use.
%
DO NOT force the wrench to achieve a task it was not designed to perform.
%
DO NOT operate the wrench when you are tired, under the influence of alcohol, drugs or intoxicating medication.
%
DO NOT get the wrench or battery charger wet or use in damp or wet locations.
%
Keep wrench and charger in the case and store in a safe, dry, childproof area where the temperature will not exceed 104
!
1.2.
BATTERY SAFETY INSTRUCTIONS
F WARNING! The battery pack contains nickel-cadmium which is dangerous. It must therefore be handled with care.
Charge battery pack prior to its first use. The battery pack will have been shipped in a low charge state.
!
Use only the charger provided to charge the battery pack.
!
DO NOT charge battery pack when room temperature is below 50
%
DO NOT attempt recharging the pack by means of an engine generator or a DC power source.
%
DO NOT short-circuit the battery pack by touching both terminals at the same time with a metal object, or your fingers etc.
%
DO NOT store battery pack (or wrench) in locations where the temperature may exceed 104
%
F WARNING! dispose of spent battery pack correctly as it contains nickel-cadmium. I DANGER! DO NOT attempt to disassemble the battery
pack. For safety and environmental reasons DO NOT discard in domestic waste or by burning. ONLY discard or recycle according to local
authority regulations.
F WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following immediate action:
Fa) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
Fb) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
1.3.
MAINS POWER ELECTRICAL SAFETY (In relation to the battery charger)
F
WARNING! It is the user’s responsibility to check the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs
p
and all electrical connections for wear and damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board.
We recommend that an RCD (Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable
products that are plugged into a supply not protected by an RCCB. If in doubt consult a professional electrician. You may obtain an RCD by contacting
your dealer. You must also read and understand the following instructions concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
person, using a Portable Appliance Tester (PAT), at least once a year.
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and the
safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.3.3. DO ensure that the insulation on all cables and the product itself is safe before connecting to the mains power supply. See 1.3.1. above
and use a Portable Appliance Tester (PAT).
1.3.4. DO ensure that cables are always protected against short circuit and overload.
p
INSTRUCTIONS FOR:
12V CORDLESS IMPACT WRENCH
CP1210/IW
Model:
F (10
C) or above 95
F (35
O
O
O
O
F (40
O
F (40
O
C).
C ) such as outside sheds, above heaters etc.
O
CP1210/IW - 0016 - (1) - 040700
C).
O
Advertisement
Related Manuals for Sealey CP1210/IW
Summary of Contents for Sealey CP1210/IW
- Page 1 CP1210/IW Model: Thank you for purchasing a Sealey product. Manufactured to a high standard this article will, if used according to these instructions and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS AND CAUTIONS.
- Page 2 NOTE: The charge time should be approximately 1 hour. 3.1.5. When charged, remove the battery from the charger and use accordingly. Disconnect the battery charger from the mains power supply and store in case. CP1210/IW - 0016 - (1) - 040700...
- Page 3 73/23/EEC LV Directive (S.I. 1994/3260) 89/336/EEC EMC Directive For Jack Sealey Ltd. Sole importer into the UK of Sealey Power Products NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.