Advertisement
Quick Links
Z Stand
Z Master
Model No. 117-0354
Model No. 121-4811
Model No. 78584
Safety
Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area of potential
danger. Replace any decal that is damaged or lost.
1. Warning—read the Operator's Manual.
2. Crushing hazard, mower—engage the parking brake, stop
the engine, and remove the ignition key before working
under the mower.
© 2013—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Kit
®
Riding Mower with 72in Deck
107-3969
Register at www.Toro.com.
Form No. 3372-957 Rev B
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3372-957* B
Printed in the USA.
Advertisement
Related Manuals for Toro 117-0354
Summary of Contents for Toro 117-0354
- Page 1 Form No. 3372-957 Rev B Z Stand ® Z Master ® Riding Mower with 72in Deck Model No. 117-0354 Model No. 121-4811 Model No. 78584 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger.
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Z Stand hub Latch bracket Assemble the Z Stand Hub Bolt (3/8 x 1-1/2 inches) Flange nut (3/8 inch) Carriage bolt (3/8 x 1-1/4 inches) (48,52 and 60 inch machines) Flange nut (3/8 inch) (48, 52 and 60 inch machines) - Page 3 Assembling the Z Stand ® Installing the Z Stand Hub Parts needed for this procedure: Parts needed for this procedure: Z Stand hub Carriage bolt (3/8 x 1-1/4 inches) (48,52 and 60 inch machines) Latch bracket Flange nut (3/8 inch) (48, 52 and 60 inch machines) Bolt (3/8 x 1-1/2 inches) Carriage bolt (3/8 x 1-1/4 inches) (72 inch machines) Flange nut (3/8 inch)
- Page 4 Installing the Z Stand Bracket Parts needed for this procedure: Carriage bolt (3/8 x 1-1/4 inches) Flange nut (3/8 inch) Bolt (1/4 x 3/4 inches) Locknut (1/4 inch) Bracket pin Lanyard Cradle bracket Procedure Note: Ensure the grass deflector is installed in the lower holes in the mower deck brackets.
- Page 5 Figure 5 Figure 4 1. Clevis pin 4. Hairpin cotter pin 1. Carriage bolts (3/8 x 1-1/4 6. Lanyard 2. Pivot pin 5. Foot inches) 3. Outer tube 2. Frame (48, 52 and 60 inch 7. Nut (1/4 inch) machines) 3.
-
Page 6: Installing The Foot Pedal
Operation Using the Z Stand® Installing the Foot Pedal The Z Stand® raises the front end of the machine to allow you to clean the mower and remove the blades. (Machines with 48, 52 and 60 inch Mower Decks) WARNING The machine could fall onto someone and cause Parts needed for this procedure: serious injury or death. - Page 7 5. Align the holes and install the clevis pin and hairpin cotter pin. Figure 9 Figure 10 1. Z Stand (Positioned in 3. Latch resting on pivot tab 1. Z Stand 3. Locked position slot) 2. Latch 4. Unlocked position 2.