Advertisement
Quick Links
CE Kit
2010 and After Groundsmaster
Model No. 117-9449
1
Install the Hood Latch
Parts needed for this procedure:
1
Latch Key
1
Latch
1
Latch Bracket
3
Carriage Screw
3
Flange Nut
Procedure
1. Park the machine on a level surface, lower the decks,
engage the parking brake and turn the engine off.
Remove the key from the ignition switch.
2. Unlatch and raise the hood.
3. Remove the plug from the square hole in the right
side of the hood. Discard the plug.
4. Remove the locking nut from the latch assembly
(Figure 1).
5. Install the locking latch through the square hole in
the right side of the hood (Figure 1). The catch
must be positioned inside the hood and pointing
downward.
Figure 1
1. Latch key
2. Latch
3. Latch bracket
© 2009—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
4. Carriage screw
5. Flange nut
Register at www.Toro.com.
®
5900/5910 Traction Unit
6. Install the locking nut onto the latch to secure it to
the hood.
7. Locate the (3) holes in the right side of the radiator
support (Figure 1). Mount the latch bracket to the
radiator support with (3) carriage screws and flange
nuts. Position the latch bracket as shown in Figure 1.
8. Close the hood slowly to see if latch catches. If
it does not, loosen the screws securing the latch
bracket to the radiator support and adjust the bracket
as necessary. Tighten the screws and verify the latch
catches.
9. Use the key to lock/unlock latch. Store the key in a
convenient and memorable place.
2
Install the Side Panel Hardware
Parts needed for this procedure:
4
Screw (5/16 x 3/4 inch)
4
Push nut (5/16 inch)
1
Hex nut (5/16 inch) For assembling push nut only
Procedure
1. Remove the existing hardware securing the side
panel to the machine and discard (Figure 2). Remove
the side panel.
Form No. 3363-186 Rev B
Installation Instructions
Original Instructions (EN)
Printed in the USA.
All Rights Reserved
Advertisement
Related Manuals for Toro 117-9449
Summary of Contents for Toro 117-9449
- Page 1 CE Kit 2010 and After Groundsmaster ® 5900/5910 Traction Unit Model No. 117-9449 Installation Instructions 6. Install the locking nut onto the latch to secure it to the hood. 7. Locate the (3) holes in the right side of the radiator support (Figure 1).
- Page 2 after removal. Loosen all of the fasteners on each cover a few turns so that the cover is loose g011939 but still attached, then go back and loosen them until the cover comes free. This will prevent you from accidentally stripping the bolts free of the retainers.
- Page 3 Note: Do not install the plastic plugs until the B. Turn the ignition key to the RUN position. spacer and stop plates are positioned under the Important: The decks will lower if the lift switches. switch is actuated when the operator is in 3.
- Page 4 the seat and the ignition key is in the RUN position. C. While using the High/Low Range diagnostic screen on the InfoCenter, move the position switch bracket just until the front Deck Down input reads OFF. Refer to the Groundsmaster 5900 Service Manual for information on InfoCenter operation.
- Page 5 G009446 Figure 9 1. CE compliance decal (Part 3. CE Warning decal (Part No. 117–2761) No. 117–2766, apply over existing decal) 2. Production year decal (included in traction unit loose parts) 2. Dampen the area with water or mildly soapy water. 3.
- Page 6 Notes:...
- Page 7 Notes:...