BE-3110 1. SCHEMATIC DIAGRAM Note : When ordering service parts, be sure to refer to "EXPLODED 1.1 OVERALL CONNECTION DIAGRAM VIEWS and PARTS LIST" or "PCB PARTS LIST" AC IN AC POWER CORD MODE REMOTE T-10 SSSB022-P06N-2 ML9-2P TB1: BZK1045...
BE-3110 2. PCB CONNECTION DIAGRAM 2.1 RF ASSY NOTE FOR PCB DIAGRAMS : 1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Page 16
BE-3110 2.3 DISPLAY ASSY F 1/2 F 1/2 DISPLAY ASSY DISPLAY ASSY (SW BOARD) (SW BOARD) SIDE B SIDE A F 1/2 DISPLAY ASSY (LED BOARD) SIDE A F 1/2, F 2/2...
Page 17
BE-3110 F 2/2 F 2/2 DISPLAY ASSY DISPLAY ASSY SIDE A SIDE B F 1/2 DISPLAY ASSY (LED BOARD) SIDE B F 1/2, F 2/2...
BE-3110 Mark No. Description Part No. Mark No. Description Part No. 3. PCB PARTS LIST • NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. • mark found on some component parts indicates the importance of the safety factor of the part.
CONV 115K) Delay. However, do not change the vertical axis and 8. CATV terminal (Equivalent to PIONEER BA-6300) horizontal axis ranges. 9. TV demodulator (Equivalent to EIDEN 463B-B) Note 3 : When reading the waveform on the oscilloscope screen, 10.
Page 22
BE-3110 4.2 Adjusting the Clamp Voltage 1. Connect the digital voltmeter to TP1 of the RF ASSY as shown in Connection Diagram 1. 2. Adjust control VR9 (RV9) of the RF ASSY so that the voltage value on the digital voltmeter becomes within DC+2.7 to 2.9V.
Page 23
: 45.75 MHz 4. Connect the devices as shown by the solid line in Connection Video Filter: off Diagram 3. ¶ BE-3110 Standby 5. Set this unit to standby. ¶ Video SG Random 6. Adjust control VR4 (RV4) of the RF ASSY so that the waveform ¶...
Page 24
BE-3110 4.6 Adjusting the Scramble Timing 1. Connect the devices as shown in Connection Diagram 5. 4. Set to the group 0 mode 1 using the key switch on the front 2. Set the devices as shown below. panel of this unit, and adjust so that the return waveform of the ¶...
Page 25
9. Adjust control VR5 (RV5) of the RF ASSY so that the bottom ¶ Video SG Staircase wave level in the key modulation of the signal comes to the position ¶ BE-3110 Clear mode (Digitally SW: 0) set in step 7. ¶ CW generator 100.15 MHz/60 dBmV/75Ω...
Page 26
BE-3110 Video Staircase wave Video in IFv out IFv in Variable RF out IFa out IFa in 115K Spectrum BE-3110 resistance TV modulator analyzer IFv in IFv out attenuator IFa in IFa out Fig. 4-10 Connection Diagram 7 4.8 Adjusting the Compression 7.
Page 27
BE-3110 17. Disconnect the cables connected to IFa in and IFa out of the unit. 21. Repeat the adjustments in section 4.6 and the adjustments in steps 18. Adjust the spectrum analyzer so that the compression modulation 1 to 20 in section 4.8 three times to raise the accuracy.