Advertisement
Quick Links
thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
instructions
protection
1. SAfety
WArninG! Wear approved eye and ear protection. Wear appropriate Personal Protective equipment. A full range of PPe is
‰
available from your Sealey stockist. Be aware of CoSHH when it applies.
WArninG! ensure Health & Safety, local authority and general workshop practice regulations are adhered to when using this
‰
equipment.
WArninG! disconnect from the air supply before changing the grinding wheel bit, servicing or performing maintenance.
‰
WArninG! ensure correct air pressure is maintained and not exceeded. Recommended air line pressure is 90psi.
‰
Maintain the tool in good condition (use an authorised service agent).
9
Replace damaged parts/bits. Use genuine parts/bits only. Unauthorised parts/bits may be dangerous and will invalidate the warranty.
9
Use in a suitable clean and tidy work area, free from unrelated materials. ensure that there is adequate lighting and ventilation.
9
Remove ill fitting clothing. Remove ties, loose jewellery and contain and/or tie back long hair.
9
Keep children and unauthorised persons away from the work area.
9
Before each use, check the grinding bit is secure and sound. If worn or damaged, replace immediately.
9
ensure the workpiece is secure. never hold a workpiece in the hand; use a vice or clamps.
9
Keep the air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
9
secure.
Prolonged exposure to vibration from this tool poses a health risk. It is the employer's/owner's responsibility to correctly assess the
9
hazard and issue guidelines for safe periods of use and offer suitable protective equipment. Safety gloves are recommended.
When not in use, disconnect from the air supply and store complete in the supplied case.
9
Wear breathing apparatus when fumes or dust pose a hazard. Be aware of and adhere to CoSHH regulations.
9
Do not grind materials containing asbestos.
8
Do not use any power source except an air compressor.
8
Do not operate the tool near any inflammable substance or on any container that has held an inflammable substance.
8
Do not use the tool for a task it is not designed to perform.
8
Do not operate the tool if unwell, tired or intoxicated.
8
Do not carry the tool by the hose, or yank the hose from the air supply.
8
WArninG! The warnings, cautions and instructions in this manual cannot cover all possible conditions and situations that may
‰
occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but
must be applied by the operator.
2. introDuCtion
Textured finish to ensure a good grip. Mini design for working in confined areas, ideal for working around engines where space is limited.
Safety trigger prevents inadvertent operation. Ideal for re-shaping, deburring and smoothing off rough edges on castings. Suitable for the
professional workshop. Supplied with fitting spanner.
3. SpeCifiCAtion
model no: ................................................................. SA1005
Air Consumption:.......................................................... 12cfm
Air Inlet Size: .............................................................1/4"BSP
Collet diameter: ............................................................. 6mm
Configuration: ..........................................................90° - Mini
Free Speed: ........................................................... 16500rpm
length: ....................................................................... 125mm
noise Power/Pressure: ........................................ 97dB/86dB
operating Pressure: ...................................................... 80psi
Vibration/Uncertainty: ................................... 1.079/0.602m/s²
© Jack Sealey limited
90° Ø6mm Collet mini Air Die GrinDer
SA1005
Model no:
Wear ear
Wear a mask
protection
Original Language Version
Wear protective
gloves
SA1005 Issue 2 (3) 18/12/19
Advertisement
Related Manuals for Sealey SA1005
Summary of Contents for Sealey SA1005
- Page 1 SA1005 Model no: thank you for purchasing a Sealey product. manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Unless the air supply system includes an oiler, lubricate the air grinder daily with a few drops of air tool oil, dripped into the in line oiler before use. [Item 4 in parts list or Sealey part no’s. ATo500S (500ml) or ATo1000S (1 litre)].
- Page 3 Warranty: Guarantee is 24 months from purchase date, proof of which is required for any claim. Sealey Group, Kempson Way, Suffolk Business park, Bury St edmunds, Suffolk. ip32 7Ar 01284 757500 01284 703534 sales@sealey.co.uk...