Advertisement
Quick Links
thank you for purchasing a sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear eye
protection
instructions
1. safety
WaRning! ensure health & safety, local authority, and general workshop practice regulations are adhered to when using this
‰
equipment.
Familiarise yourself with application and limitations, as well as the specific potential hazards peculiar to the riveter.
9
Replace or repair damaged parts. Use genuine parts only. Non authorised parts may be dangerous and will invalidate the warranty.
9
Keep the riveter clean for best and safest performance.
9
Locate riveter in an adequate working area for its function, keep area clean & tidy and free from unrelated materials and ensure there
9
is adequate lighting.
Keep children and unauthorised persons away from the working area.
9
Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain and/ or tie back long hair.
9
WaRning! Always wear approved eye or face protection when operating the riveter.
‰
Keep fingers, hands and body clear of all working parts and do not place any items within the riveter lattice.
9
Familiarise yourself with the push action to ensure you do not accidentally wrench your wrist when pushing sharply.
9
Maintain correct balance and footing. Ensure the floor is not slippery and wear non slip shoes.
9
Secure non stable work piece with a clamp, vice or other adequate holding device.
9
Ensure that all used rivet ends are disposed of in a safe manner.
9
Do not get the riveter wet or use in wet locations.
8
Do not use the riveter for any purpose other than for which it is designed.
8
Do not operate the riveter when you are tired, under the influence of alcohol, drugs or intoxicating medication.
8
Do not allow untrained persons to operate the riveter.
8
Do not operate the riveter if any parts are damaged or missing as this may cause failure or possible personal injury.
8
2. intRoDuction
Precision made, high grade alloy steel jaws with strong aluminium body. Forged alloy steel pins and bolts with double handle bearings for
long life and durability. Suitable for blind aluminium, steel and stainless steel rivets. Includes Chrome Molybdenum special profile nozzles for
structural rivets up to 6.4mm(1/4").
3. specification
nozzles: .....................................4.8/5.0mm, 6.0mm, 6.4mm.
Structural Nozzles: ....................................... 4.8mm, 6.4mm.
4. opeRation
The AK395 is suitable for aluminium, steel and stainless steel rivets. The tool includes Chrome Molybdenum nozzles for structural
rivets .
4.1.
nozzles
4.1.1.
Select the appropriate nozzle. Differing
sizes are located at points (A) (fig 1).
4.1.2.
To remove nozzle at head (B) use the
wrench supplied. ensure the replacement
nozzle is completely screwed in a lightly
tighten with wrench.
4.2.
to operate.
4.2.1.
Hold the head (C) and pull the handle so
that the lattice (D) is completely extended.
WaRning! Ensure your fingers are clear of moving parts. Insert rivet shaft all the way into the nozzle (B).
‰
4.2.2.
Insert rivet head completely into the prepared work piece hole.
4.2.3.
Hold the riveter firmly and push on the handle to completely close the lattice which will fix the rivet in place and cut the shaft. Should
riveting not be achieved on the first try then re-extend the lattice and push once more.
4.2.4.
Once completed, pull the handle to extend the lattice again to eject the shaft end from the nozzle. Safely discard of shaft ends.
5. Maintenance
5.1.
Keep the riveter clean.
© Jack Sealey limited
Heavy Duty Lazy tongs RiveteR
model no:
Crushing of
hands
Original Language Version
aK395
fig.1
AK395 Issue 2 (HF) 11/04/18
Advertisement
Related Manuals for Sealey AK395
Summary of Contents for Sealey AK395
- Page 1 Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Warranty: Guarantee is 12 months from purchase date, proof of which is required for any claim. sealey group, Kempson Way, suffolk Business park, Bury st edmunds, suffolk. ip32 7aR 01284 757500 01284 703534 sales@sealey.co.uk www.sealey.co.uk Original Language Version AK395 Issue 2 (HF) 11/04/18 ©...