Advertisement
Table of Contents
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Wear Eye
Instructions
Protection
1. SAFETY
WARNING! Ensure Health & Safety, local authority, and general workshop practice regulations are adhered to when using this
R
equipment.
Familiarise yourself with this product's application and limitations, as well as the potential hazards peculiar to the riveter.
WARNING! Disconnect the riveter from the air supply before changing accessories, servicing or performing any maintenance.
R
Maintain the riveter in good condition (use an authorised service agent).
Replace or repair damaged parts. Use genuine parts only. Unauthorised parts may be dangerous and will invalidate the warranty.
Use in a suitable work area. Keep area free from unrelated materials and ensure that there is adequate lighting.
Keep the riveter clean for best and safest performance.
WARNING! Always wear approved eye (or face) and hand protection when operating the riveter.
R
M aintain correct balance and footing. Do not over reach, ensure the floor is not slippery, wear non-slip shoes.
R emove ill fitting clothing. Remove ties, watches, rings, loose jewellery. Contain or tie back long hair.
Wear appropriate protective clothing and keep hands and body clear of working parts.
Keep the riveter away from your body and at a safe distance from others.
Keep children and unauthorised persons away from the working area.
Secure non stable workpieces with a clamp, vice or other adequate holding device.
Ensure that spent rivet stems are disposed of correctly and do not cause a hazard.
WARNING! Ensure correct air pressure is maintained and not exceeded. Recommended pressure:85-90psi.
R
Keep air hose away from heat, oil and sharp edges. Check air hose for wear before each use and ensure that all connections are
secure.
Avoid unintentional starting.
DO NOT use the riveter for a task it is not designed to perform.
DO NOT operate the riveter if any parts are damaged or missing as this may cause failure and/or personal injury.
DO NOT carry by the hose, or pull the hose from the air supply.
DO NOT get the riveter wet or use in damp or wet locations or areas where there is condensation.
DO NOT allow untrained persons to operate the riveter.
DO NOT operate the riveter when you are tired or under the influence of alcohol, drugs or intoxicating medication.
DO NOT direct air from the air hose at yourself or others.
When not in use, disconnect from the air supply and store in a safe, dry, childproof location.
2. INTRODUCTION
Powerful, extra heavy-duty tool suitable for aluminium, steel, stainless steel rivets and structural rivets from 3/16" to 1/4". Trigger operated
riveter with hardened steel jaw assembly and air-actuated vacuum rivet shaft collector. Resilient grip for added comfort and hanging loop for
use with balancer. Supplied with three riveting nozzles, two spanners and oil can.
3. SPECIFICATIONS
Model no: ..............................................................SA316.V3
Nozzle sizes: ........ 3/16"(4.8mm), 7/32"(5.6mm), 1/4"(6.4mm)
Air consumption: ............................................................ 4cfm
Operating pressure: ...................................................... 90psi
Air inlet size:..............................................................1/4"BSP
Weight: .......................................................................... 1.9kg
Noise power: .............................................................82dD(A)
Noise pressure: ......................................................... 71dB(A)
Vibration figure: .......................................................... 0.5m/s²
Uncertainty: .............................................................. 0.54m/s²
© Jack Sealey Limited
INSTRUCTIONS FOR
AIR/HYDRAULIC RIVETER HEAVY-DUTY
VACUUM SYSTEM
SA316.V3
MODEL NO:
Original Language Version
SA316.V3 | Issue 1 12/05/15
Advertisement
Table of Contents
Related Manuals for Sealey SA316.V3
Summary of Contents for Sealey SA316.V3
- Page 1 SA316.V3 MODEL NO: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
-
Page 2: Air Supply
WARNING! Ensure you disconnect the tool from the air supply system before attempting any service or maintenance. 6.1. Maintain the tool with care. Keep it oiled for optimum performance. 6.2. LUBRICATION 6.2.1. Lubricate the air tool daily with a high quality air tool oil, (such as Sealey Part No. ATO/500 or ATO/1000). 6.2.2. Add oil to the hydraulic system occasionally. 6.2.3. Unscrew the oil tank plug (Fig.5) and fill with SAE 10 oil until the oil level reaches the bottom of the plug hole. It is recommended that the oil seal, part No: SA316.49 be replaced during this procedure. 6.2.4. Re-fit the oil plug screw. Original Language Version SA316.V3 | Issue 1 12/05/15 © Jack Sealey Limited... -
Page 3: Troubleshooting
Grit or gum deposits in the tool may cut power and can be corrected by cleaning the air strainer and flushing out the tool with gum solvent oil or an equivalent de-greaser. 6.4.3. If all outside conditions are in order, disconnect the tool from the air supply, disassemble and replace any worn or damaged parts with Sealey original parts. 6.4.4. Clean all parts, reassemble the tool and lubricate. 6.5. Store the tool in a safe, dry, secure environment. - Page 4 NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice. IMPORTANT: No liability is accepted for incorrect use of this product. WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim. Sole UK Distributor, Sealey Group. 01284 757500 www.sealey.co.uk Kempson Way, Suffolk Business Park, Bury St.
- Page 5 WARNING! – Risk of Hand Arm Vibration Injury. This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately. This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC. This tool is to be operated in accordance with these instructions. Measured vibration emission value (a): ...0.5 m/s² Uncertainty value (k):.