hit counter script
Husqvarna S 13 Workshop Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Vacuum Cleaner
  5. S 13
  6. Workshop manual

Husqvarna S 13 Workshop Manual

Hide thumbs Also See for S 13:
Table of Contents

Advertisement

Quick Links

Workshop manual
S 13, S 26, S 36
English
1347 - 001 -

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna S 13

Summary of Contents for Husqvarna S 13

  • Page 1 Workshop manual S 13, S 26, S 36 English 1347 - 001 -...

  • Page 2: Table Of Contents

    6 Troubleshooting 6.1 Troubleshooting schedule........13 7 Product overview for repair and servicing 7.1 Product overview for repair instructions (S 13)..14 7.2 Product overview for repair instructions (S 26)..15 7.3 Product overview for repair instructions (S 36)..16 8 Repair instructions 8.1 To clean and examine the product parts....17...

  • Page 3: Introduction

    1 Introduction 1.1 Document description This manual gives a full description of how to do maintenance and repair on the product. It also gives safety instructions that the personnel must obey. 1.2 Target group This manual is for personnel with a general knowledge of how to do repair and do servicing.

  • Page 4: Safety Definitions

    2 Safety 2.1 Safety definitions Warnings, cautions and notes are used to point out Always use an approved breathing mask. specially important parts of the manual. WARNING: Used if there is a risk of injury or death for the operator or bystanders if the Always use approved ear protection.

  • Page 5: Prepare And Do Servicing On The Product 3.1 Maintenance Schedule

    3 Prepare and do servicing on the product 3.1 Maintenance schedule The maintenance intervals are calculated from daily use of the product. The intervals change if the product is not used daily. Maintenance Before each Daily Weekly When suction 6 months or 12 months or is low 1000h...

  • Page 6: Servicing Data

    4 Servicing data 4.1 Servicing data (S 13) 22.8 - 25.2 Nm 77.0 - 85.1 Nm 22.8 - 25.2 Nm 6 - Servicing data 1347 - 001 -...
  • Page 7 22.8 - 25.2 Nm 9.3 - 10.3 Nm 2.8 - 3.0 Nm 22.8 - 25.2 Nm 9.3 - 10.3 Nm 1347 - 001 - Servicing data - 7...

  • Page 8: Servicing Data (S 26)

    4.2 Servicing data (S 26) 77.0 - 85.1 Nm 22.8 - 25.2 Nm 8 - Servicing data 1347 - 001 -...
  • Page 9 22.8 - 25.2 Nm 9.3 - 10.3 Nm 2.8 - 3.0 Nm 22.8 - 25.2 Nm 9.3 - 10.3 Nm 1347 - 001 - Servicing data - 9...

  • Page 10: Servicing Data (S 36)

    4.3 Servicing data (S 36) 71.0 - 85.1 Nm 22.8 - 25.2 Nm 10 - Servicing data 1347 - 001 -...
  • Page 11 22.8 - 25.2 Nm 9.3 - 10.3 Nm 5.4- 6.0 Nm 9.3 - 10.3 Nm 9.3 - 10.3 Nm 5.4 - 6.0 Nm 9.3 - 10.3 Nm 9.3 - 10.3 Nm 9.3 - 10.3 Nm 2.8 - 3.0 Nm 1347 - 001 - Servicing data - 11...

  • Page 12: Function Overview

    5 Function overview 5.1 Type plate/Product serial number The product serial number is given on the type plate. Supply the model name and the article number when you send an order for spare parts. 5.2 Type plate overview 1. Model 2.

  • Page 13: Troubleshooting

    6 Troubleshooting 6.1 Troubleshooting schedule Problem Cause Solution There is no power supply. Connect the product to a power source. The power cord is defective. Replace the power cord. The motor does not start. The ON/OFF switch is defective. Replace the ON/OFF switch. The soft start unit is defective.

  • Page 14: Product Overview For Repair And Servicing

    7 Product overview for repair and servicing 7.1 Product overview for repair instructions (S 13) 1. Top cover 5. Motor box 2. Prefilter 6. Frame 3. Container 4. HEPA filter 14 - Product overview for repair and servicing 1347 - 001 -...

  • Page 15: Product Overview For Repair Instructions (S 26)

    7.2 Product overview for repair instructions (S 26) 1. Top cover 5. Motor box 2. Prefilter 6. Frame 3. Container 4. HEPA filter 1347 - 001 - Product overview for repair and servicing - 15...

  • Page 16: Product Overview For Repair Instructions (S 36)

    7.3 Product overview for repair instructions (S 36) 1. Top cover 2. Prefilter 3. Container 4. HEPA filter 5. Motor box 6. Frame 16 - Product overview for repair and servicing 1347 - 001 -...

  • Page 17: Repair Instructions

    8 Repair instructions 8.1 To clean and examine the product parts 8.2.2 To remove the jet pulse cleaning kit 1. Remove the 3 screws and rivets on the top cover to • Clean and examine all parts fully. You find more get access to the jet pulse cleaning kit.
  • Page 18 8.3.2 To replace the prefilter CAUTION: Do not clean a HEPA filter. This causes damage to the HEPA filter. WARNING: Use approved protective gloves when you replace the prefilter. CAUTION: Make sure to not touch the inner surface of the HEPA filter. This cause damage 1.

  • Page 19: Container

    8.5 Motor box • To clean the prefilter with jet pulse cleaning kit, do these steps: 8.5.1 To disconnect the circuit board (S 13) a) Start the product. b) Close the inlet valve to seal the inlet. To replace the 1.
  • Page 20 8.5.2 To replace the ON/OFF switch To disconnect the 1. Remove the motor tube. Refer to circuit board (S 13) on page 19 . 2. Make a note of the positions of the cables on the ON/OFF switch. 3. Disconnect all the cables from the ON/OFF switch.
  • Page 21 Position Cable color Grey Light blue Brown, soft start unit Black, hour meter Black, hour meter Blue, soft start unit White 8.5.3 To remove the soft start unit and the 3. Remove the 8 screws and remove the motor housing. electronic filter (S 26) To replace the 1.
  • Page 22 4. Remove the manometer tube. 6. Cut the cable strip that holds the cables together. 7. Remove the hour meter cables (C) from the ON/OFF switch (A). 5. Remove the 3 nuts. Remove the motor tube to get access to the cables. 8.
  • Page 23 unless it is necessary to replace a motor or 3. Pull the cables behind the right motor to the a power cord. electronic filter. 12. Cut the brown (H) and blue (I) cables from the soft start unit. 13. Pull out the brown (H) and blue (I) cables of the soft start unit from behind the motor.
  • Page 24 8.5.5 To remove the soft start unit and the 4. Spray glass cleaning agent on the tubes to make it easy to remove the top of the motor housing. electronic filter (S 36) WARNING: Use approved personal protection when you remove the HEPA filter. Refer to replace the HEPA filter on page 17 .
  • Page 25 6. Remove the 4 screws at the bottom of the motor 10. Remove the wires that go into the ON/OFF switch. housing. Remove the 2 screws on the inner side of Remove the manometer tube. the inlet. 11. Loosen the 5 nuts that attach the ground wires to the 7.
  • Page 26 13. Use a flat screwdriver and a hammer to carefully Position Cable color remove the soft start unit (A). If a rivet attaches the Brown, ON/OFF switch soft start unit to the frame, drill the rivet off. Brown, soft start unit Blue, ON/OFF switch Blue, 2 cables Ground...

  • Page 27: Transportation, Storage And Disposal

    9 Transportation, storage and disposal 9.1 Transportation of the product • Remove the dust from the container. • Put the product in a closed vehicle during transportation. • Do not put the product in frost or rain during transportation. • Let the product stay in an upright position during transportaton.

  • Page 28: Diagrams

    10 Diagrams 10.1 Electrical diagram (S 13), 230 V 28 - Diagrams 1347 - 001 -...
  • Page 29 Item Description Quantity Motor Cable clip White cable Brown cable Yellow/green cable 0.15 Terminal 2-pol White cable Switch Sealing ring Brown cable Cord set Cable clip Filter Cable clip Black cable Yellow/green cable 0.65 Screw Toothed washer Lock washer Locknut Screw Lock washer 1347 - 001 -...

  • Page 30: Electrical Diagram (S 13), 230 V

    10.2 Electrical diagram (S 13), 230 V 30 - Diagrams 1347 - 001 -...

  • Page 31: Electrical Diagram (S 26), 230 V, 50 Hz

    10.3 Electrical diagram (S 26), 230 V, 50 Hz MOT 1 MOT 2 Item Description Part no Quantity Motor Cable clip Brown cable 1.05 White cable 1.05 Black cable 0.95 Cable clip Switch Cord set 1347 - 001 - Diagrams - 31...
  • Page 32 Item Description Part no Quantity Cable clip Yellow/green cable 0.15 Blue cable 0.65 Filter Cable clip Blue cable 0.65 Screw Toothed washer Lock washer Locknut Screw Lock washer Yellow/green cable 2 x 0.55 32 - Diagrams 1347 - 001 -...

  • Page 33: Electrical Diagram (S 26), 230 V, 50 Hz

    10.4 Electrical diagram (S 26), 230 V, 50 Hz 1347 - 001 - Diagrams - 33...

  • Page 34: Electrical Diagram (S 26), 110 V

    10.5 Electrical diagram (S 26), 110 V PLUG GLAND SOFT GND1 STARTER 34 - Diagrams 1347 - 001 -...

  • Page 35: Electrical Diagram (S 26), 120 V

    10.6 Electrical diagram (S 26), 120 V 1347 - 001 - Diagrams - 35...
  • Page 36 Item Description Black cable AWG16 300 mm Black cable AWG16 300 mm Switch Hour meter Power inlet Soft start unit 120 V Ground wire 520 mm Ground wire 520 mm 36 - Diagrams 1347 - 001 -...

  • Page 37: Electrical Diagram (S 36)

    10.7 Electrical diagram (S 36) PLUG GLAND EMI FILTER GND1 SOFT STARTER motor wagon 1347 - 001 - Diagrams - 37...

  • Page 38: Electrical Diagram (S 36)

    10.8 Electrical diagram (S 36) ELECTRICAL ENCLOUSURE PLUG GLAND OUTLET 250V PCBA GND1 motorbox wagon SOFT STARTER 38 - Diagrams 1347 - 001 -...

  • Page 39: Electrical Diagram (S 36) Us, 120 V

    10.9 Electrical diagram (S 36) US, 120 V PLUG GLAND SOFT STARTER motor box GND1 wagon 1347 - 001 - Diagrams - 39...

  • Page 40: Technical Data

    11 Technical data 11.1 Technical data Data S 13 [220 - S 26 [220 - S 36 [220 - S 13 [110 - S 26 [110 - 230V] 230V] 230V] 120V] 120V] Rated Voltage (1 220 - 230 220 - 230...

  • Page 41: Technical Data

    11.2 Technical data Data S 26 [220 - S 36 [220 - S 13 [110 - S 26 [110 - S 36 [110 - 230V] 230V] 120V] 120V] 120V] Rated Voltage (1 110 - 120 220 - 230 220 - 230...
  • Page 42 42 - Technical data 1347 - 001 -...
  • Page 43 1347 - 001 - Technical data - 43...
  • Page 44 598892502 2019-10-23...

This manual is also suitable for:

S 26S 36

Table of Contents