Advertisement
Quick Links
Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these
instructions, and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE
PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
1. SAFETY
1.1. GENERAL
Ensure the lamp is fully charged before initial use.
DO NOT turn the lamp on when it is being charged.
DO NOT shine directly into your, other person's or animal's eyes.
DO NOT allow children to use the lamp.
DO NOT handle or move the lamp whilst it is being charged.
DO NOT use the lamp if you suspect that the battery or the lamp casing is damaged.
DO NOT leave battery in a discharged state, recharge battery immediately. Before storage, fully recharge the battery, subsequently
recharge the battery at least once every six months of non-use.
1.2. ELECTRICAL SAFETY FOR USE OF CHARGER.
USE ONLY THE SUPPLIED CHARGER PLUG FOR CONNECTING LAMP TO THE POWER SUPPLY.
WARNING! It is the user's responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices.
An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products, particularly portable equipment which is plugged into an electrical supply
not protected by an RCCB.
You must also read and understand the following instructions concerning electrical safety.
1.2.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by a qualified
electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.2.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance and
the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.2.3. You must ensure that you:
Inspect the charger plug, cable and connector for wear and damage to ensure items are safe before connecting to the mains power
supply.
If worn or damaged DO NOT use.
Important: Check that the voltage marked on the charger plug is the same as the lamp.
Uncoil the cable between charger and the lamp.
DO NOT pull the charger plug from the mains socket by the lead.
WARNING! DO NOT use any other type of charger with this product, other than the supplied mains or car charger. Failure to observe
this warning could result in injury and or fire and will invalidate the warranty.
DO NOT try to take the charger plug apart.
DO NOT use the charger plug to charge or power any other electrical item.
DO NOT get the charger wet, or use in wet, damp conditions (for indoor use only).
1.3 Battery Safety
WARNING! To reduce the risk of burns or fire:
DO NOT Attempt to open, disassemble, modify or service the battery pack.
DO NOT Crush, puncture, short external contacts or dispose of in fire or water.
DO NOT Expose to temperatures above 60°C (140°).
Replace only with the battery pack designated for this product.
Recycle or dispose of used battery as stipulated by local regulation.
If the electrolyte in the cells gets on your skin, thoroughly wash with soap and water. If it gets in your eyes, rinse thoroughly with cool
water and seek immediate medical attention.
2. INTRODUCTION
Heavy-duty housing features 24 super bright SMDs. 7 LEDs in the end for use as a directional torch. 360° Hanging hook and magnet on rear
of lamp for hands-free applications. Single LED battery indicator. Supplied with 12V in-car charger and mains charger
3. SPECIFICATION
Model No: ..............................................................................LED307.V2
Battery: .................................................................3.7V 1.5Ah Lithium-ion
LED Qty: ................................................................... SMD (24) + LED (7)
Lumen Output: .................................. 150lm (Lamp Body) + 20lm (Head)
Operating Time: .........................3Hours (Lamp Body) +16 Hours (Head)
Charging Time: .................................................................................. 5hrs
Length:.......................................................................................... 210mm
4. CHARGING
Note: Fully charge the lamp before first use.
4.1 Connect the charger into the charging port (Fig.1) on the bottom of the lamp. Plug into power supply and turn on, the charging LED (Fig.1)
will light RED to show charging has commenced.
4.2 When the battery has fully charged the LED will change to GREEN.
© Jack Sealey Limited
INSTRUCTION MANUAL FOR:
CORDLESS 24 SMD + 7 LED LITHIUM-ION
RECHARGEABLE INSPECTION LAMP
LED307.V2
MODEL No:
Original Language Version
.
LED307.V2
Issue: 1 - 08/04/14
Advertisement
Related Manuals for Sealey LED307.V2
Summary of Contents for Sealey LED307.V2
- Page 1 LED307.V2 MODEL No: Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED.
- Page 2 Valpak’s registered compliance scheme. Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705 Parts support is available for this product. To obtain a parts listing and/or diagram, please log on to www.sealey.co.uk, email sales@sealey.co.uk or phone 01284 757500.