Page 1 ® Satellite Series User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see page 157 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm.
Page 2 AFFILIATES AND SUPPLIERS DO NOT WARRANT THAT OPERATION OF THE PRODUCT WILL BE UNINTERRUPTED OR ERROR FREE. YOU AGREE THAT TOSHIBA, ITS AFFILIATES AND SUPPLIERS SHALL HAVE NO RESPONSIBILITY FOR DAMAGE TO OR LOSS OF ANY BUSINESS, PROFITS, PROGRAMS, DATA OR...
Page 3 Only Peripherals complying with the FCC Class B limits may be attached to this equipment. Operation with noncompliant peripherals or peripherals not recommended by Toshiba is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's parallel port, monitor port, USB port, PS/2 port and microphone jack.
Page 4: Industry Canada Requirement
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada.
Page 5: Telephone Company Procedures
If trouble is experienced with this equipment, for repair or limited warranty information, please contact Toshiba Corporation, Toshiba America Information Systems, Inc. or an authorized representative of Toshiba, or the Toshiba Support Centre within the United States at (800) 457-7777 or Outside the United States at (949) 859-4273.
Page 6 Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment NOTICE: The Industry Canada label identifies certified equipment.
Page 7: Wireless Interoperability
USOC RJ11C. Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖...
Page 8: Wireless Lan And Your Health
Wireless LAN device prior to turning on the equipment. Regulatory Information The TOSHIBA Wireless LAN Mini PCI Card must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. This device complies with the following radio frequency and safety standards.
Page 9 ETS 300 328 Technical requirements for radio equipment ETS 300 826 General EMC requirements for radio equipment. English: Hereby, TOSHIBA Corp. Digital Media Network Company, declares that this Radio LAN device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.
Page 10 Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp. Digital Media Network Company dat deze Radio LAN device voldoet aan de essentiële eisen en aan de overige relevante bepalingen van Richtlijn 1999/5/EC.
Page 11 Caution: Exposure to Radio Frequency Radiation The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits. Nevertheless, the TOSHIBA Wireless LAN Mini PCI Card shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 12 Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems.
Page 13: Device Authorization
The interference range of this equipment is less than 40m. 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100...
Page 14: Radio Approvals For Wireless Devices
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ Do not disassemble or modify the device. ❖ Do not install the embedded wireless module into other device. ❖ 5.17 GHz to 5.23 GHz for indoor use only Radio approvals for wireless devices NOTE The following information is dependent on what type of wireless device is in...
Page 15 Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ For private usage outside buildings across public grounds over less than Belgique: 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m.
Page 16 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Europe - Restrictions for use of 5 GHz Frequencies in European Community Countries European Community Countries Austria Belgium, France, Switzerland/Lichtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK...
Page 17 ❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
Page 18 802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Turbo Mode (5 GHz) Canada Approved Countries/Regions for use for the Intel Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table.
Page 19: Bluetooth Wireless Technology Interoperability
New Zealand Portugal Sweden Bluetooth wireless technology Interoperability Bluetooth™ Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖...
Page 20: Bluetooth Wireless Technology And Your Health
Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.com/computers/tnt/bluetooth.htm in Europe or http://www.pcsupport.global.toshiba.com in the United States for...
Page 21: Regulatory Statements
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization.
Page 22 The radiated output power of the Bluetooth™ Card from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth™ Card from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Page 23 Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement.
Page 24 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-13-1100 Direct Dial: 03-3457-5916...
Page 25 Copyright This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed, however, with respect to the use of the information contained herein.
Page 26 ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance. Dolby - Manufactured by Toshiba under license from Dolby Laboratories/ Dolby and the double-D symbol are trademarks of Dolby Laboratories. TouchPad is a trademark of Synaptics, Inc.
Page 27 MultiMediaCard is a trademark of Infineon Technologies AG. All other brand and product names are trademarks or registered trademarks of their respective companies. Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org.
Page 28: Table Of Contents
Other precautions ...45 Important information on your computer’s Setting up your computer ...47 Setting up your software...47 Registering your computer with Toshiba ...48 Adding external devices ...49 Connecting to a power source ...49 Charging the main battery...52 cooling fan ...46...
Page 29 Using the computer for the first time ...53 Opening the display panel ...53 Your computer’s features and specifications ...54 Turning on the power ...54 Using the TouchPad™...55 Scrolling with the TouchPad™ ...56 Using the Scroll button ...56 Using the Control buttons ...56 Disabling or enabling the TouchPad ...57 Installing additional memory (optional) ...58 Removing a memory module...62...
Page 30 Powering down the computer ...99 Using the Turn off computer or Shut down Using Hibernation Mode ...102 Using Standby Mode...104 Toshiba’s online resources ...106 Chapter 3: Mobile Computing... 107 Toshiba’s energy-saver design...107 Running the computer on battery power ...108 Battery Notice ...108 Power management ...109...
Page 31 Charging the main battery...110 Charging the RTC battery...111 Monitoring battery power ...112 Determining remaining battery power...113 What to do when the battery runs low ...114 Setting battery alarms...115 Conserving battery power ...115 Power profiles in Windows XP...116 Using a hot key to set the power profile...117 Changing the main battery ...118 Removing the battery from the computer ...118 Inserting the battery into the computer...120...
Page 32 Removing Memory Stick or Memory Stick Inserting an SD™ Card...148 Removing an SD™ Card...149 Inserting an xD-Picture Card™...149 Removing an xD-Picture Card™...150 Chapter 5: Toshiba Utilities... 151 TOSHIBA Console ...151 Customizing Your Computer...152 Network ...152 Power Saver ...153 Mouse utility ...155 Hotkey utility ...155...
Page 33 Modem problems...180 Develop good computing habits ...180 If you need further assistance...181 Before you call ...182 Contacting Toshiba ...182 Other Toshiba Internet Web sites ...183 Toshiba’s worldwide offices...184 ® operating system is not working ..160 ® XP operating system can help you ...162...
Page 34 Display brightness ...191 Disabling or enabling the TouchPad ...192 Keyboard hot keys ...192 Appendix B: Power Cable Connectors ...193 Appendix C: Using ConfigFree™ with your Toshiba Computer ...194 Getting Started...195 Starting ConfigFree ...195 ConfigFree Utilities...196 Connectivity Doctor ...196 Search for Wireless Devices ...199 Profile Settings ...201...
Page 35: Introduction
Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer. For specific information on the software, see the Microsoft booklet that shipped with your computer.
Page 36: This Guide
Toshiba's Web site at While Toshiba has made every effort at the time of publication to ensure the accuracy of the information provided herein, product specifications, configurations, prices, system/ component/options availability are all subject to change without notice.
Page 37: Safety Icons
Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Page 38: Other Icons Used
Guides for other programs that may come preinstalled on your computer or that are available for installation on your Recovery media (if applicable to your system). ❖ For accessory information, visit Toshiba's Web site at accessories.toshiba.com. ❖ The Microsoft documentation, which explains the features of the operating system.
Page 39: Service Options
Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see “If Something Goes Wrong” on page...
Page 40: Chapter 1: Getting Started
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your computer. Selecting a place to work Your computer is designed to be used in a variety of locations and situations.
Page 41: Keeping Yourself Comfortable
❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than the speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters.
Page 42 Getting Started Selecting a place to work twisting your torso or neck and look at the screen without slouching. ❖ If you use an external monitor, the top of the screen should be no higher than eye level. ❖ If you use a paper holder, set it at the same height and distance as the screen.
Page 43 extra back support. Lower-back-support cushions are available at many office supply stores. ❖ Sit with your back straight so that your knees, hips, and elbows form approximately 90-degree angles when you work. Do not slump forward or lean back too far. Lighting Proper lighting can improve the readability of the display and reduce eyestrain.
Page 44: Work Habits
Getting Started Selecting a place to work Using the computer keyboard incorrectly may result in discomfort and possible injury. If your hands, wrists, and/or arms bother you while typing, stop using the computer and rest. If the discomfort persists, consult a physician. Work habits The key to avoiding discomfort or injury from strain is to vary your activities.
Page 45: Other Precautions
Other precautions Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer. ❖...
Page 46: Important Information On Your Computer's Cooling Fan
Getting Started Selecting a place to work Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both. ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers.
Page 47: Setting Up Your Computer
Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” on page 47 or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards.
Page 48: Registering Your Computer With Toshiba
A window displays, asking if you wish to register with Toshiba and Microsoft. Click Yes to register, or No to exit the process. If you click No, you may register with Toshiba by clicking the NOTE Register with Toshiba icon on the desktop.
Page 49: Adding External Devices
Adding external devices Before adding external devices, Toshiba recommends setting NOTE up your software. See Before starting to use your computer, you may also want to: ❖ Add more memory (see (optional)” on page ❖ Connect a mouse (see ❖...
Page 50 Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter.
Page 51 Sample connecting the power cord/cable to the AC adapter cord Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Plug the AC adapter cord into the DC-IN on the back of the computer.
Page 52: Charging The Main Battery
Getting Started Charging the main battery The battery light: ❖ Glows amber while the battery is being charged. ❖ Glows green when the battery is fully charged. ❖ Is unlit when the computer is not connected to an external power source. For information on determining battery power, see Damaged power cords/cables can cause fire or electric shock.
Page 53: Using The Computer For The First Time
TECHNICAL NOTE: When your computer is using all of the power provided by the AC Adaptor to run applications, features, and devices, the recharging of the battery can not occur. Your computer's Power Saver utility can be used to select a power level setting that reduces the power required for system operation and will allow the battery to recharge.
Page 54: Your Computer's Features And Specifications
Getting Started Using the computer for the first time manufactured using high-precision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the NOTE computer, the brightness of the LCD Screen will deteriorate.
Page 55: Using The Touchpad
Turn on the computer by pressing and releasing the power button located on the top of the keyboard. When you turn on the computer for the first time, do not turn NOTE off the power again until the operating system has loaded completely.
Page 56: Scrolling With The Touchpad
Getting Started Using the TouchPad™ Because the TouchPad is much smaller than the display NOTE screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can perform clicking functions by either double-tapping the TouchPad or clicking the control buttons.
Page 57: Disabling Or Enabling The Touchpad
Disabling or enabling the TouchPad The TouchPad is enabled by default. To change the enable/ disable TouchPad setting: Click Start, then click Control Panel. The Control Panel window appears. Click Printers and Other Hardware. Click the Mouse icon or press the Fn + F9 hot keys. Click the TouchPAD ON/OFF tab.
Page 58: Installing Additional Memory (Optional)
Additional memory comes in various capacities (to stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com). “Disabling or enabling the TouchPad” on...
Page 59 Installing additional memory (optional) There are two memory slots. Depending on your system configuration, both slots may be occupied. If you use the computer for a long time, the memory modules become hot. If this happens, let the memory modules cool to room temperature before you replace them.
Page 60 Getting Started Installing additional memory (optional) Memory slot cover Sample locating the memory module slot cover Remove the battery (see page 118). Using a standard Phillips no. 1 screwdriver, unscrew the captive screws that secure the expansion memory slot cover, then remove the memory slot cover. Sample removing the memory module slot cover Place the cover in a safe place so that you can retrieve it later.
Page 61 Installing additional memory (optional) Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer).
Page 62: Removing A Memory Module
Getting Started Installing additional memory (optional) Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. Replace the expansion memory slot cover. Retighten the screws. Turn the computer over and reconnect any cables you removed.
Page 63 Installing additional memory (optional) Sample removing the memory module Complete the procedure by following steps 11 through 14 “Installing additional memory (optional)” on page Checking total memory When you add or remove memory, you can check that the computer has recognized the change. To do this: Click Start, then click Control Panel.
Page 64: Using A Mouse
Getting Started Using a mouse Using a mouse You may want to use a mouse instead of the computer’s built- in TouchPad. You can use a USB-compatible mouse. After logging on to your system, the mouse cursor may move NOTE to the upper-right side of the screen.
Page 65: Setting Up Your Printer
You must supply the proper printer cable. If one did not come NOTE with your printer, you may purchase one from an electronics or computer store. These instructions assume you have a USB printer, consult the document that came with your printer to verify the connection type.
Page 66 Getting Started Connecting a local printer Click Start, Control Panel, and then Printers and Other Hardware. Select Printers and Faxes. The operating system opens the Printers and Faxes window. Sample Printers and Faxes window Click Add Printer. The Add Printer Wizard appears. Sample Add Printer Wizard dialog box Click Next.
Page 67 The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the Windows ® XP operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual for more information. If the printer you are setting up: ❖...
Page 68: Using External Display Devices
Getting Started Using external display devices The operating system prompts you to print a test page. If your printer is connected and turned on, click Next. To complete the setup procedure without printing a test page, click No, then click Next. Click Finish.
Page 69: Selecting Video Cables
For the best video quality, always use a properly shielded cable. HINT: Toshiba recommends using a cable no longer than 20 feet (approximately 6 meters). Using a poor quality cable may result in a dull or fuzzy picture, poor color, ghosting, video noise, or loss of video.
Page 70: Directing The Display Output When You Turn On The Computer
Getting Started Using external display devices TECHNICAL NOTE: If you are connecting to a television, you may need to change the display properties. Most televisions use or support an 800 x 600 standard resolution. Connecting an external monitor or projector You can easily attach an external monitor or projector to your computer if you need a larger screen.
Page 71: Adjusting The Quality Of The External Display
❖ Built-in display and TV (or other external video device) simultaneously ❖ TV (or other external video device) only Release the TECHNICAL NOTE: You can also change these settings using the Display Properties Box. Set the option for the video controller by clicking Start, then Control Panel and clicking Display.
Page 72: Turning Off The Computer
Getting Started Turning off the computer Turning off the computer It is a good idea to turn off your computer when you are not using it for a while. If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery.
Page 73: Caring For Your Computer
To keep your computer clean, gently wipe the display panel and exterior case with a lightly dampened cloth. Ask your Toshiba dealer for suggestions for appropriate cleaning products. Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the drive indicator light stops glowing) and all external peripheral cables are disconnected.
Page 74: Using A Computer Lock
Getting Started Caring for your computer Using a computer lock For your own peace of mind, you may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional PORT-Noteworthy Computer Lock Cable.
Page 75: Chapter 2: Learning The Basics
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved.
Page 76 Learning the Basics Computing tips ❖ Back up your files to disks (or other removable media) on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy.
Page 77: Using The Keyboard
Using the keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows the functionality of a full-size keyboard. Sample keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖...
Page 78: Ctrl, Fn, And Alt Keys
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys Ctrl Sample Ctrl, Fn, and Alt keys , and Ctrl program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the 12 keys at the top of the keyboard.
Page 79: Overlay Keys
Overlay keys Sample numeric and cursor control overlay The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard.
Page 80: Starting A Program
Learning the Basics Starting a program To turn off the numeric keypad overlay, hold down the and press indicator panel goes out. Using the overlay for cursor control To turn the cursor control overlay on, press simultaneously. The cursor control mode light on the keyboard indicator panel glows when the cursor control overlay is on.
Page 81: Starting A Program From The Start Menu
The next three sections explain how to start a program from the Start menu, Explorer, and the Run dialog box. Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows Click Start, then point to All Programs.
Page 82: Starting A Program From The Run Dialog Box
Learning the Basics Starting a program Click Windows Explorer. Click My Computer to expand the window. In the left part of the window, under the C: icon, click the folder containing the program, in this case Program Files. Windows folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder.
Page 83: Saving Your Work
In the Run dialog box: ❖ If you know the program’s location, type the command line. For a program in the Windows program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\WindowsNT\Accessories\Wordpad, ❖ If you do not know the location, click Browse... In the Browse dialog box, enter the file name (for example, wordpad.exe) and select the drive to search.
Page 84: Saving Files
Learning the Basics Saving your work Saving files On the File menu of your Windows If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box.
Page 85: Printing Your Work
File names If you plan to share your files with a computer using a pre- ® Windows 95 version of the Windows file name must be no more than eight characters long. Typically the file name also has an extension, consisting of a period and up to three additional characters.
Page 86: Backing Up Your Files
Learning the Basics Backing up your files To print a file: If your printer is not on, turn it on now. Open the File menu of your Windows Print. The program displays a Print dialog box. Sample Print dialog box Specify the print parameters.
Page 87: Restoring Your Work
Using the DVD-ROM or multi-function drive Click Start, then click My Computer. Click the drive that contains the file you want to copy. Double-click the folder that contains the file, then click the file you want to copy. HINT: You can use the Ctrl or Shift keys to select more than one file.
Page 88: Drive Components And Control Buttons
Learning the Basics Using the DVD-ROM or multi-function drive For these reasons, your computer may come with a DVD- ROM drive or multi-function drive. TECHNICAL NOTE: Your DVD-ROM or multi-function drive is set to play region 1 (North America) DVD-ROMs. If you play a DVD disc from another region, the drive will automatically change to play in the format of the other region.
Page 89: Dvd-Rom Or Multi-Function Drive Components
Using the DVD-ROM or multi-function drive DVD-ROM or multi-function drive components Your DVD-ROM or multi-function drive may look like this: Eject button Manual eject hole Sample DVD-ROM or multi-function drive shown Drive in-use indicator light—Indicates when the drive is in use.
Page 90: Media Control Buttons
Learning the Basics Using the DVD-ROM or multi-function drive Media control buttons The control buttons located to the right of the keyboard let you play audio CDs when the computer is off. You can also use them to play CDs and DVDs when the computer is on. Music CD button Stop/eject Previous track...
Page 91: Inserting A Disc
Using the DVD-ROM or multi-function drive The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently playing. The stop/eject button stops a disc that is currently playing. You can eject a disc by pressing the stop/eject button twice.
Page 92 Learning the Basics Using the DVD-ROM or multi-function drive HINT: The drive will not open if the computer’s power is off. Grasp the tray and pull it fully open. Sample drive tray fully extended Hold the disc by its edges and check that it is clean and free of dust.
Page 93 If you insert the disc incorrectly, it may jam the drive. If this happens, contact your Toshiba support for assistance. Push the disc tray in by pressing gently on the center of the tray until it clicks into place.
Page 94: Playing An Audio Cd
Learning the Basics Using the DVD-ROM or multi-function drive Playing an audio CD Insert an audio CD and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD select the Play Audio CD using Windows Media click OK.
Page 95 Using the DVD-ROM or multi-function drive Rewind Play Stop Previous track Next track Mute Sample Windows Media The Windows Media Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel.
Page 96: Playing Cds Using Auto-Run
Learning the Basics Using the DVD-ROM or multi-function drive Playing CDs using Auto-Run If you insert a CD into the DVD-ROM/multi-function drive and the Auto-Run feature does not automatically start your disk, try launching the CD manually. To do this, follow these steps: Open the Start menu and select My Computer.
Page 97: Viewing The Contents Of A Cd Or Dvd
Using the DVD-ROM or multi-function drive Viewing the contents of a CD or DVD CDs and DVDs contain files just like the hard disk. CDs are often used to install software or store files that require lots of space, such as photographs and large presentation files. You can use Explorer or My Computer to view the contents of any CD or DVD.
Page 98: Removing A Disc With The Computer Off
Learning the Basics Using the DVD-ROM or multi-function drive Removing a disc with the computer off Insert a slender object, such as a straightened paper clip, into the manual eject button access hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it.
Page 99: Powering Down The Computer
Powering down the computer Pushing the power button before shutting down the Windows operating system could cause you to lose your work. Make sure the system indicator panel’s disk light and the drive-in- use light are off. If you turn off the power while a disk is being accessed, you may lose data or damage the disk and/or drive.
Page 100 Learning the Basics Powering down the computer When starting up again, the system does not automatically open the programs and files you were previously using. If your computer is not connected to a domain server: Click Start, select Turn off computer. The Turn off computer dialog box appears.
Page 101 To use either of these methods, you first need to turn it on in Toshiba’s Power Saver utility. Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click on the Setup Action tab. Select the following from the drop-down lists. ❖...
Page 102: Using Hibernation Mode
Learning the Basics Powering down the computer For more information about the Power Saver utility, see NOTE “Power Saver” on page Starting again after Shut down To start the computer up again, press the power button until the on/off light changes to green. If you shut down the computer by closing the display panel, you can start it again by opening the display panel.
Page 103 Configuring your computer for Hibernation Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. Select Hibernation for the options you want. ❖ When I press the power button Set this option to Hibernate so that the computer will go into Hibernation mode when you press the power button.
Page 104: Using Standby Mode
Learning the Basics Powering down the computer Starting again from Hibernation mode To restart the computer from Hibernation mode, press the power button until the on/off light turns green. The computer returns to the screen you were previously using. If you place the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Page 105 To use any of these methods, you first need to enable them in Toshiba’s Power Saver utility. Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. Learning the Basics Powering down the computer...
Page 106: Toshiba's Online Resources
Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect. These sites provide information about Toshiba products, give help with technical questions, and keep you up to date with future upgrades.
Page 107: Chapter 3: Mobile Computing
Many of these energy-saving features have been set by Toshiba. We recommend you leave these features active, allowing your computer to operate at its maximum energy efficiency, so that you can use it for longer periods of time...
Page 108: Running The Computer On Battery Power
Toshiba Web site at accessories.toshiba.com. To ensure that the battery maintains its maximum capacity, operate the computer on battery power at least once a month until the battery is fully discharged.
Page 109: Power Management
Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s Global Support Centre. Using additional batteries If you spend a lot of time traveling and need to work for many hours without an AC power source, you may want to carry additional charged batteries with you.
Page 110: Charging The Batteries
Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com. Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet.
Page 111: Charging The Rtc Battery
The battery may not start charging immediately under the following conditions: ❖ The battery is extremely hot or cold. To ensure that the battery charges to its full capacity, wait until it reaches room temperature. ❖ The battery is almost completely discharged. Leave the power connected and the battery should begin charging after a few minutes.
Page 112: Monitoring Battery Power
Mobile Computing Monitoring battery power It is seldom necessary to charge the RTC battery because it NOTE charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode is enabled and the RTC battery is completely discharged, a warning prompts you to reset the real-time clock.
Page 113: Determining Remaining Battery Power
Click the Toshiba Power Saver icon. The current power source and battery power remaining section displays the current charge state of the battery. The value displays as a percentage of remaining battery charge. Sample Toshiba Power Saver Properties Dialog Box Mobile Computing Monitoring battery power...
Page 114: What To Do When The Battery Runs Low
Mobile Computing Monitoring battery power The remaining battery charge is indicated on the top-left side of the dialog box. With repeated discharges and recharges, the battery’s capacity gradually decreases. A frequently used older battery does not power the computer for as long as a new battery, even when both are fully charged.
Page 115: Setting Battery Alarms
To change the default alarm settings: Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Toshiba Power Saver icon. Click the Setup Action tab. Select the Alarm settings in the Setup Alarm section. Before your computer runs out of battery power, save your data and take one of the following actions: ❖...
Page 116: Power Profiles In Windows Xp
By using them, you can greatly increase the length of time you can use the computer before you need to recharge the battery. Toshiba has combined these options into preset power usage modes or profiles. Power profiles in Windows XP...
Page 117: Using A Hot Key To Set The Power Profile
Using a hot key to set the power profile You may use a hot key to set the power profile. To set the power profile: Press pop-up window. Sample Power Profile mode pop-up window While continuing to press desired power profile. The power profile options are: Full Power, High Power, Normal, DVD Playback, Presentation, and Long Life.
Page 118: Changing The Main Battery
Mobile Computing Changing the main battery Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or short- circuit its terminals.
Page 119 If the battery lock is in the locked position, slide it toward the unlocked position. Sample sliding the battery lock to the unlocked position Slide and hold down the battery release latch. Sample pressing the battery release latch While holding the battery release latch, lift the battery out of the computer.
Page 120: Inserting The Battery Into The Computer
Mobile Computing Changing the main battery Sample removing the discharged battery pack If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in Inserting the battery into the computer Assuming you just removed the battery pack (see the battery from the computer”...
Page 121: Taking Care Of Your Battery
If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through to Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries.
Page 122: Maximizing Battery Life
Mobile Computing Taking care of your battery ❖ When you install the battery pack, you should hear a click when it is seated properly. ❖ Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖...
Page 123: Disposing Of Used Batteries
Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by Toshiba. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state, and local laws, it may be illegal to dispose of old batteries by placing them in the trash.
Page 124: Traveling Tips
❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, and compact discs. Contact your authorized Toshiba representative for more information.
Page 125: Chapter 4: Exploring Your Options
Chapter 4 Exploring Your Options In this chapter, you will explore some of the special features of your Satellite Exploring the desktop The desktop is the launching pad for everything you can do in ® the Windows system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Page 126: Finding Your Way Around The Desktop
Exploring Your Options Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Icons Start button Sample Windows Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Page 127 Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help.
Page 128: System Tray
Exploring Your Options Exploring the desktop Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows.
Page 129: Setting Up For Communications
Internet To stay current on the most recent software and hardware NOTE options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com. Exploring Your Options Setting up for communications...
Page 130: Determining The Com Port
Exploring Your Options Setting up for communications Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports. The default setting for the modem is COM3. The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings.
Page 131: Connecting The Modem To A Telephone Line
Click OK to close the properties dialog box for that specific modem. Click OK to close the Modem Properties dialog box. Close the Control Panel. Connecting the modem to a telephone line Before you can communicate using the modem, you need to connect it to a telephone line.
Page 132: Connecting Your Computer To A Network
Now you are ready to send a fax or use the modem to connect to an online service or the Internet. For more detailed information regarding your computer’s modem, visit Toshiba’s Web site at accessories.toshiba.com. Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports.
Page 133 To avoid this delay, you can reconfigure Windows to disable the LAN port. TECHNICAL NOTE: You can also use ConfigFree to reconfigure Windows to disable the LAN port. For procedures, “Using ConfigFree™ with your Toshiba Computer” on page 194. To disable the LAN port: Click Start, click Control Panel, then Performance and Maintenance.
Page 134 Your computer may have an integrated Wi-Fi Wireless LAN Mini PCI module. It is recommended that you do not remove the module from your computer. For assistance, contact a Toshiba Wireless Authorized Service Partner. ® Wireless LAN Mini PCI module...
Page 135: An Overview Of Using The Internet
For systems equipped with Wi-Fi, flip the wireless on/off switch to the On position. To enable a wireless device, use the NOTE “Enabling a wireless device” on page 191 information). An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features.
Page 136: Internet Service Providers
Exploring Your Options An overview of using the Internet The World Wide Web offers information as text, images, audio, or video to be referenced from anywhere in the world. Special programs called Web browsers are specifically designed to work with HTTP. They make it easier to connect to a particular network address and send and receive information.
Page 137: Surfing The Internet
If you are using your computer at the office, then you probably connect to the Internet through your company’s network. See your network administrator about connecting to the Internet. Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page.
Page 138: Uploading And Downloading Files From The Internet
Exploring Your Options Exploring video features A news group is similar to a chat room, but instead of using a dedicated site to converse about a specialized subject with others in real-time, it uses a Web site as a clearinghouse where all the messages are placed, like a gigantic bulletin board.
Page 139: Changing The Display Properties Setting
Changing the display properties setting Right-click anywhere on your desktop and select Properties. The Display Properties dialog box appears. Sample Display Properties dialog box Click the Settings tab. Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply. The screen blinks momentarily while the settings are adjusted.
Page 140: Exploring Audio Features
Exploring Your Options Exploring audio features Exploring audio features You can use your computer to record sounds using an external microphone. You can play .wav sound files or audio CDs using the built-in speakers, headphones, or external speakers. SRS TruSurround XT may ship with your computer. NOTE SRS TruSurround XT is available only when using WinDVD applications.
Page 141: Using A Microphone
Using a microphone To record high-quality sounds, you can attach a microphone: Connect an external microphone to the computer, by locating the microphone jack on the right side of the computer. Plug the microphone cord into the microphone jack. Turn on the microphone. Click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder.
Page 142: Using External Speakers Or Headphones
Exploring Your Options Exploring audio features Adjusting recording quality The better the quality of the recording, the more disk space the sound file requires. Experiment to find a balance that fits your needs. Open Sound Recorder, if necessary. (Click Start, point to All Programs, Accessories, Entertainment, then click Sound Recorder.) In the Sound Recorder window, click Edit, then click...
Page 143: Connecting A Monitor, Keyboard And Mouse
Connecting a monitor, keyboard and mouse To adjust the volume: ❖ For external speakers, use the volume controls for the speakers. ❖ For headphones, use the computer’s volume control dial. Connecting a monitor, keyboard and mouse By connecting an external monitor, external full-size keyboard and a mouse, you can work with your notebook as if it were a standard office desktop computer.
Page 144: Pc Card Supporting Software
Exploring Your Options Inserting and removing PC Cards PC Card supporting software PC Cards require Card and Socket Services software — a set of programs that acts as a translator between the PC Card and the computer, and that makes hot swapping (switching cards while the computer is on) possible.
Page 145: Removing A Pc Card
Insert the PC Card. Sample inserting a PC Card When the card is almost all the way into the slot, push firmly, but gently, to ensure a firm connection with the computer. Do not force the card into position. To avoid damaging the PC Card or the computer, do not force the card into the PC Card slot.
Page 146: Setting Up A Pc Card For Your Computer
Exploring Your Options Inserting and removing PC Cards Sample ejecting a PC card The PC Card ejects slightly from the slot. Grasp the edges of the PC Card and slide it out of the slot. Setting up a PC Card for your computer Some PC Cards are ready to use as soon as you install them.
Page 147: Using The Bridge Media Slot
Before removing a PC Card, stop it by clicking the Safely Remove Hardware icon on the System tray. Once the PC Card has stopped, you can safely remove it. See Card” on page Never swap modules when the computer is in Hibernation or Standby mode.
Page 148: Removing Memory Stick Or Memory Stick Pro Media
Exploring Your Options Using the Bridge Media slot Sample inserting Memory Stick or Memory Stick PRO media Do not remove Memory Stick media while data is being written or read. Even when the message “copying...” in the windows disappears, writing to the media might still be in progress and your data could be destroyed.
Page 149: Removing An Sd Card
Sample inserting an SD Card Do not touch the SD expose the storage area to static electricity, which can destroy data. Do not remove an SD Even when the message “copying...” in the windows disappears, writing to the card might still be in progress and your data could be destroyed.
Page 150: Removing An Xd-Picture Card
Exploring Your Options Using the Bridge Media slot Sample inserting an xD-Picture Card Do not touch the xD-Picture could expose the storage area to static electricity, which can destroy data. Do not remove an xD-Picture or read. Even when the message “copying...” in the windows disappears, writing to the card might still be in progress and your data could be destroyed.
Page 151: Chapter 5: Toshiba Utilities
❖ Hotkey utility ❖ Power Saver TOSHIBA Console The TOSHIBA Console provides quick access to computer functions and allows you to customize a range of computer settings. To access the control panel: Click Start, then click All Programs. Point to TOSHIBA Console, then click the resulting Toshiba Console selection.
Page 152: Customizing Your Computer
Toshiba Utilities TOSHIBA Console Sample TOSHIBA Console window The TOSHIBA Console offers two categories of features: ❖ Customizing Your Computer ❖ Network Customizing Your Computer The features available in this category are: ❖ Power Saver ❖ Mouse ❖ Toshiba Button Control ❖...
Page 153: Power Saver
You can either use one of the preset modes or create and use your own customized profile. The preset profiles cannot be deleted. By changing the options that appear in the Toshiba Power Saver Properties window and clicking OK, you can reconfigure that function. Any options that you change...
Page 154 Toshiba Utilities TOSHIBA Console Profiles This section lists the preset profiles. The preset profiles are: ❖ Full Power ❖ High Power ❖ Normal ❖ DVD Playback ❖ Presentation ❖ Long Life Although you can change the properties for any of these profiles, this is not recommended.
Page 155: Mouse Utility
Standby ] and Hibernation [ Fn+F3 To activate: Click Start, All Programs, Toshiba, Utilities, then click the Hotkey utility. The Toshiba Hotkey window appears. Sample Toshiba Hotkey utility window Select the desired option.
Page 156: Cd/Dvd Drive Acoustic Silencer
Toshiba Utilities TOSHIBA Console CD/DVD Drive Acoustic Silencer Sample CD/DVD Drive Acoustic Silencer screen This utility can slow the speed of your optical drive to make it run more quietly. You can use this utility to make listening to Music CDs more enjoyable.
Page 157: Chapter 6: If Something Goes Wrong
This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
Page 158 If Something Goes Wrong Problems that are easy to fix Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Select the program you want to close, then click End Task.
Page 159: Problems When You Turn On The Computer
Save the file and refer to it when you contact the software manufacturer. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adapter and power cable properly or installed a charged battery.
Page 160: The Windows Operating System Is Not Working
If Something Goes Wrong The Windows The computer displays the message. The computer was placed in Stand By mode and the battery has discharged. Data stored in the computer’s memory has been lost. To charge the battery, leave the computer plugged into a live wall outlet for several hours.
Page 161: Using Startup Options To Fix Problems
The Windows Using Startup options to fix problems If the operating system fails to start properly, you may have to change your system’s configuration or verify the startup procedure to fix the problem. To do this, use the options in the Startup menu.
Page 162: Internet Problems
If Something Goes Wrong The Windows See your Windows TECHNICAL NOTE: If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet.
Page 163: Resolving A Hardware Conflict
The Help and Support window appears. Then do one or both of the following: ❖ In the search field, type the topic of the problem with which you need help and follow the on-screen instructions. ❖ Click a problem about which you would like help from the listings and follow the on-screen instructions.
Page 164: Resolving Hardware Conflicts On Your Own
If Something Goes Wrong Resolving a hardware conflict The recommended procedure for getting multiple devices to work together is to add and set up one device at a time. After you add each device, test it to make sure it and all previously connected devices work.
Page 165: Fixing A Problem With Device Manager
Play-compliant, no two devices will compete for the same system resources. Simply plug in the device and turn on your computer. The operating system automatically sets up your system to accommodate the new device. If you install an older (legacy) device that the operating system cannot recognize, the operating system may have difficulty assigning resources to it.
Page 166 If Something Goes Wrong Resolving a hardware conflict Disabling a device Open the Start menu, click Control Panel, then Performance and Maintenance. Click the Administrative Tools icon. Click the Computer Management and then Device Manager. Select the specific device from the device category. In the toolbar, look to the far right for an icon of a monitor with a strike mark through a circle on the front.
Page 167: Memory Problems
❖ The General tab, which provides basic information about the device. ❖ The Resource tab, which lists resources assigned to the monitor, DVD-ROM, multi-function drive, diskette disk drive, and other power-using functions. ❖ The Drivers tab, which displays the drivers being used by the device.
Page 168: Power And The Batteries
If Something Goes Wrong Resolving a hardware conflict memory module installed, the error is not caused by the memory module. TECHICAL NOTE: You must have a least one memory module installed for the computer to work. Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and real-time clock (RTC) battery).
Page 169: Keyboard Problems
If the battery has completely discharged, it will not begin charging immediately. Leave the AC adapter and power cable connected, wait 20 minutes and see if the battery is charging. If the battery light is glowing after 20 minutes, let the computer continue charging the battery for at least another 20 minutes before you turn on the computer.
Page 170: Display Problems
If Something Goes Wrong Resolving a hardware conflict You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer.
Page 171 The screen does not look right. You can change the display settings by clicking a blank area of the desktop with the secondary control button, then clicking Properties. This opens the Display Properties dialog box. The Appearance tab of this dialog box allows you to choose the colors for the screen.
Page 172: Disk Drive Problems
If Something Goes Wrong Resolving a hardware conflict The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher. Devices that do not support this resolution will only work in Internal/External mode.
Page 173 Error-checking Run Error-checking, which analyzes the directories, files, and File Allocation Table (FAT) on the disk and repairs any damage it finds: To run Error-checking: Click Start, then click My Computer. Right-click the drive you want to check and select Properties from the menu.
Page 174: Dvd-Rom Or Multi-Function Drive Problems
If Something Goes Wrong Resolving a hardware conflict Some programs run correctly but others do not. This is probably a configuration problem. If a program does not run properly, refer to its documentation and check that the hardware configuration meets its needs. A diskette will not go into the external diskette drive.
Page 175: Sound System Problems
Examine the disc to see whether it is dirty. If necessary, wipe it with a clean damp cloth dipped in water or a neutral cleaner. Replace the disc in the tray. Make sure it is lying flat, label side uppermost. Press the disc down until it locks on the spindle.
Page 176: Pc Card Problems
If Something Goes Wrong Resolving a hardware conflict in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager.
Page 177 PC Card checklist ❖ Make sure the card is inserted properly into the slot. “Inserting and removing PC Cards” on page 143 information about how to insert PC Cards. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective PC Card slips through quality control.
Page 178 If Something Goes Wrong Resolving a hardware conflict The computer stops working (hangs) when you insert a PC Card. The problem may be caused by an I/O (input/output) conflict between the PCMCIA socket and another device in the system. Use Device Manager to make sure each device has its own I/O base address.
Page 179: Printer Problems
If the card is attached to an external device, check that the connection is secure. Refer to the card’s documentation, which should contain a troubleshooting section. Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on, and ready (online).
Page 180: Modem Problems
If Something Goes Wrong Develop good computing habits will print. Contact the software manufacturer for more information. Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack.
Page 181: If You Need Further Assistance
On a regular basis, back up the information stored on your hard disk. Here are some ways you can do this: ❖ Copy files to diskette, following the steps in work” on page ❖ Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape.
Page 182: Before You Call
GO, and then clicking the Detailed Specs link from the menu on the left, or just refer to the computer documentation shipped with your product. For the number of a Toshiba dealer near you in the United States, call: (800) 457-7777. Contacting Toshiba...
Page 183: Other Toshiba Internet Web Sites
Information about what you were doing when the problem occurred. ❖ Exact error messages and when they occurred. For technical support, call the Toshiba Global Support Centre: Within the United States at (800) 457-7777 Outside the United States at (949) 859-4273 Other Toshiba Internet Web sites toshiba.com...
Page 184: Toshiba's Worldwide Offices
Germany Toshiba Europe GmbH Leibnizstraße 2 D-93055 Regensburg Germany Japan Toshiba Corporation, PCO-IO 1-1, Shibaura 1-Chome Minato-Ku, Tokyo, 105-8001 Japan Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF.
Page 185 United States Toshiba America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618 United States For more information on additional Toshiba worldwide locations, please visit: www.toshiba.co.jp/index.htm. If Something Goes Wrong Toshiba’s worldwide offices United Kingdom Toshiba Information Systems (U.K) Ltd.
Page 186: Appendix A: Hot Keys
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute This hot key enables/disables volume mute on your computer.
Page 187: Instant Password Security
The power usage profiles are: Full Power, High Power, Normal, DVD Playback, Presentation, and Long Life. Sample power usage modes The properties of each mode are set in the Toshiba Power Saver utility. For more information, see Computing” on page Hot Keys Instant password security 107.
Page 188: Stand By Mode
Hot Keys Stand By mode Stand By mode This hot key places the computer into Stand By mode. A message box is displayed by default to confirm that the computer is going into Stand By mode. This message box can be set so it does not display. Sample Stand By confirmation box For more information about Stand By mode, please see “Using Standby Mode”...
Page 189: Hibernation Mode
Hibernation mode This hot key places the computer into Hibernation mode. If Hibernation mode is enabled (the default), a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display. Sample Hibernation confirmation box If Hibernation mode is disabled, this hot key will not respond.
Page 190: Display Modes
Hot Keys Display modes Display modes This hot key cycles through the power-on display options. The display modes are: Sample display options window To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Page 191: Enabling A Wireless Device
Enabling a wireless device This hot key enables/disables the optional wireless devices in your computer. The wireless modes are: Wi-Fi enabled—This enables the Wi-Fi module. Wi-Fi disabled—This disables the Wi-Fi module. Sample wireless modes window Display brightness This hot key decreases the screen brightness. This hot key increases the screen brightness.
Page 192: Disabling Or Enabling The Touchpad
Hot Keys Disabling or enabling the TouchPad Disabling or enabling the TouchPad This hot key enables/disables the TouchPad. To use the TouchPad, see TouchPad” on page Sample disable and enable TouchPad windows Keyboard hot keys This hot key turns the cursor control overlay on and off. This hot key turns the numeric overlay on and off.
Page 193: Appendix B: Power Cable Connectors
Appendix B Power Cable Connectors The computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada UL approved CSA approved Australia AS approved United Kingdom...
Page 194: Toshiba Computer
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks.
Page 195: Getting Started
Networking, ConfigFree. ❖ Double-click the ConfigFree icon ❖ Press the Toshiba Console button (if applicable to your system) to open the Toshiba Console, and then click the ConfigFree icon. ❖ Click the ConfigFree icon click the desired utility. If your computer is not connected to a network, the ConfigFree NOTE icon on the taskbar is displayed with an “X.”...
Page 196: Configfree Utilities
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Page 197 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the device’s Wired Equivalent Privacy (WEP) key...
Page 198 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point.
Page 199: Search For Wireless Devices
Using ConfigFree™ with your Toshiba Computer Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN devices and Bluetooth devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: Click the Click Search for Wireless Devices.
Page 200 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample viewing Wi-Fi devices The following screen shows an example of Bluetooth devices that are detected. As with the Wi-Fi screen, moving the mouse pointer over a device icon displays information about the device.
Page 201: Profile Settings
Using ConfigFree™ with your Toshiba Computer Click your own computer at the center of the map. Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device.
Page 202 Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities ❖ Personal firewall settings for Internet connections. ❖ Dial-up connection settings for the default connection. ❖ File and printer sharing settings. ❖ Printer settings for the default printer. To create a profile: Click the Move the pointer to Profile.
Page 203: Quick Connect
Quick Connect The Quick Connect feature switches the Wireless LAN connection to connect to a Toshiba Wireless Projector. Once the projector utility is installed, launching the Quick Connect utility automatically opens the Wireless Data Projector Application.
Page 204 (DPJ), then click Connect. Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and re- established later.
Page 205 Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed. ❖ If you select Toshiba Wireless Projector (DPJ) from the ConfigFree tray menu (this disconnects the wireless LAN connection). ❖ If you select a profile from the ConfigFree tray menu or when you disable a wireless device.
Page 206: Using The Automatic Switch
Using ConfigFree™ with your Toshiba Computer Using the Automatic Switch Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home.
Page 207: Semi-Automatic Switch Feature
Using ConfigFree™ with your Toshiba Computer Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can then click this window to connect using the settings specified in the profile.
Page 208: Glossary
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms These acronyms may appear in this user’s guide. BIOS CD-ROM CD-RW CMOS COM1 COM2 alternating current basic input/output system bits per second compact disc compact disc read-only memory compact disc rewrite memory complementary metal-oxide semiconductor...
Page 209 direct current direct memory access DIMM dual inline memory module disk operating system dots per inch DSTN dual supertwist nematic digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory enhanced capabilities port EPROM erasable programmable read-only memory file allocation table Federal Communications Commission fast infrared...
Page 210 Glossary SCSI DDRAM SRAM SVGA Terms These terms may appear in this user’s guide. active-matrix display—A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology. Also known as a “TFT display,” in its simplest form there is one thin film transistor (TFT) for each cell.
Page 211 application—A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. backup—A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. basic input/output system (BIOS)—See BIOS.
Page 212 Glossary byte—A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte. cache—A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory.
Page 213 controller—A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU—See central processing unit (CPU). CPU cache—A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs.
Page 214 Glossary disk—A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive—The device that reads and writes information and programs on a diskette or hard disk.
Page 215 DVD-ROM (digital versatile [or video] disc read-only memory)—A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. emulation—A technique in which a device or program imitates another device or program.
Page 216 Compare software. Hibernation—A feature of many Toshiba notebook computers that saves to the hard disk the current state of your work, including all open files and programs, when you turn the computer off. When you turn on the computer again, your work is returned to the same state it was when the computer was turned off.
Page 217 hot swapping—The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. icon—A small image displayed on the screen that represents a function, file, or program. interlaced—A method of refreshing a computer screen, in which only every other line of pixels is refreshed.
Page 218 Glossary local area network—See LAN. logical drive—A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives.
Page 219 non-interlaced—A method of refreshing a computer screen, in which each pixel of every line is refreshed as the electron beam scans across and down the screen. Compare interlaced. non-system disk—A disk for storing programs and data that cannot be used to start the computer. Compare system disk. online—Available through the computer.
Page 220 Glossary port—A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor—See central processing unit (CPU). program—A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility.
Page 221 ROM (read-only memory)—Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up.
Page 222 Glossary universal serial bus (USB)—A serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single all-purpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial.
Page 223: Index
Index AC adapter 49 AC power cable connectors 193 AC power light 51 accessories carrying cases 73 memory 58 Add Printer Wizard 65 adjusting recording quality 142 Alt keys 78 arm/wrist strain 43 audio .wav files 140 features 140 Auto-Run 96 avoiding injury 41 backing up files 76 battery...
Page 224 Index playing using Auto-Run 96 CD and DVDs viewing contents 97 CD Player control panel 95 inserting 92 problem solving 175 channels DMA 164 IRQ 164 character keys 77 charging the battery 52 checking device properties 166 click 56 communications network connection 132 system resources 164 compact discs...
Page 225 latch 53 screen is blank 170 display device connecting 68 external 68 TV 68 display modes hot key 190 display output settings 70 display panel opening 53 Display settings hot key 139 display, external adjusting 71 disposal information 27 disposing of used batteries 123 DMA (Direct Memory Access) 164 double-click 56 DVD-ROM or multi-function drive...
Page 226 Index starting again from 104 Hibernation mode hot key 189 hot key display modes 190 display settings 139 functions 186 Hibernation mode 189 keyboard 192 keyboard overlays 192 power usage mode 187 Stand By mode 188 volume mute 186 wireless mode 191 hot key power usage mode 117 hot key utility 155 hot swapping 144...
Page 227 Memory Stick inserting 147 removing 148 microphone 141 Microsoft Support Online Web site modem determining COM port 130 problem solving 180 resetting port to default settings upgrading 130 module memory 61 Wi-Fi Mini PC 134 monitor 68 connecting 68 not working 170 mouse installing 64 serial 64...
Page 228 175 computer hangs when PC Card inserted 178 computer will not power up 159 contacting Toshiba 182 corrupted/damaged data files Device Manager 165 disabling a device 166 disk drive is slow 173 display is blank 170...
Page 229 flickers 171 system resources 164 trouble prevention 180 URL address not found 162 using Startup options 161 warning resume failure 160 Windows won’t start 159 Windows XP Media Center Edition not working 160 program, starting 80 programs not running correctly 174 projector 68 connecting 70 protection of stored data 2...
Page 230 68 adjusting display 71 connecting 68 Toshiba Internet Web sites 183 Toshiba Console 151 Toshiba online resources 106 Toshiba utilities 151 traveling tips 124 turning off the computer 72 turning on the power 54 Universal Resource Locator (URL) using...

Toshiba P30-S6362ST User Manual

Chapter 1: Getting Started

Chapter 2: Learning the Basics

Chapter 3: Mobile Computing

Chapter 4: Exploring Your Options

Chapter 5: Toshiba Utilities

Chapter 6: If Something Goes Wrong

Appendix A: Hot Keys

Appendix B: Power Cable Connectors

Appendix C: Using Configfree™ with Your Toshiba Computer

Quick Links

Related Manuals for Toshiba P30-S6362ST

Summary of Contents for Toshiba P30-S6362ST