Related Manuals for Toro E-Z Vac TimeCutter HD 79345
Summary of Contents for Toro E-Z Vac TimeCutter HD 79345
- Page 1 Form No. 3414-381 Rev A E-Z Vac ™ Complete Twin Bagger TimeCutter ® HD Riding Mower Model No. 79345—Serial No. 400000000 and Up *3414-381* A Register at www.Toro.com. Original Instructions (EN)
-
Page 2: Table Of Contents
Safety and Instructional Decals ......... 4 product properly and safely. Setup ................5 You may contact Toro directly at www.Toro.com for product 1 Preparing the Machine........... 6 and accessory information, help finding a dealer, or to register 2 Installing the Weight..........6 your product. -
Page 3: Safety
• Allow the machine to cool before storing it. loss of traction and loss of control. Reduce towed weight and slow down. The following list contains safety information specific to Toro • Stopping distance increases with the weight of the towed products and other safety information you must know. -
Page 4: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-4164 136-4164 1. Warning—read the Operator’s Manual. 4. Cutting/dismemberment hazard, impeller—keep away from moving parts;... -
Page 5: Setup
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Weight tray Left weight-tray mount Right weight-tray mount Suitcase weight—16 kg (35 lb) Retaining rod Install the weight. -
Page 6: Preparing The Machine
Determine the left and right sides of the machine from the normal operating position. Preparing the Machine Installing the Weight No Parts Required Parts needed for this procedure: Weight tray Procedure Left weight-tray mount Right weight-tray mount Perform the following procedure to prepare the machine for attaching the blower and finishing kit. -
Page 7: Removing The Grass Deflector And Belt Cover
g196533 Figure 3 g196560 Figure 5 Cutaway view 1. Retaining rod 3. Suitcase weight 1. Weight-tray mounts 3. Flange nut (3/8 inch) 2. Weight tray 2. Bolt (3/8 x 1-1/4 inches) 4. Self-tapping bolt (5/16 x 3/4 inch) 5. Insert the retaining rod into the tray and rotate it into the locked position (Figure 3. -
Page 8: Installing The Baffle And Blower Support
Installing the Baffle and Blower Support Parts needed for this procedure: Blower support Hex washer-head screw (3/8 x 3/4 inch) Baffle Carriage bolt (5/16 x 3/4 inch) Flange nut (5/16 inch) Procedure g190642 1. Install the blower support to the mower deck using Figure 6 2 hex washer-head screws (3/8 x 3/4 inch) as shown 1. - Page 9 2. Remove the existing bolt and nut from the mower deck (Figure Important: For 48-inch and 60-inch mower decks, there is only one bolt and nut that you can remove. For 54-inch mower deck, remove the bolt and nut as shown in Figure g206496 Figure 10...
-
Page 10: Installing The Pulley Assembly, Belt Cover, And Shoulder Bolt
Installing the Pulley Assembly, Belt Cover, and Shoulder Bolt Parts needed for this procedure: Pulley assembly Belt cover g201435 Figure 12 1. Belt cover 2. Screw (1/4 x 1/2 inch) Procedure 1. Remove the nut and washer from the right mower deck pulley. - Page 11 g201214 g201215 Figure 15 Figure 13 1. Machine frame 4. Bolt (5/16 x 1 inch) 1. Nut 3. Bolt 2. Locknut (5/16 inch) 5. Pivot frame 2. Existing hitch bracket 3. Hole 2. Install the stabilizer bracket to the engine guard using 2 5.
-
Page 12: Installing The Latch Rod
Installing the Latch Rod Parts needed for this procedure: Latch rod Hairpin cotter Procedure Install the latch rod with a hairpin cotter (Figure 18). g028306 Figure 17 Left side shown 1. Pivot frame hole 4. Support rod 2. Washer 5. Keyed slot (existing) 3. -
Page 13: Installing The Bagger Top
2. Install the screen as shown in Figure 19 and ensure that it slopes down toward the collection bags. Note: Make sure that the screens snap into place and the tabs engage the bagger top. Installing the Bagger Top Parts needed for this procedure: Grass Bag Procedure 1. -
Page 14: Installing The Blower Assembly
4. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 21). Installing the Blower Assembly Parts needed for this procedure: Blower assembly Procedure WARNING An uncovered discharge opening allows the lawn mower to throw objects toward you or bystanders, resulting in serious injury. -
Page 15: Installing The Blower Belt And Powered Bagger Cover
(page 14). Use the following belt based on the mower deck size: 48-inch Mower 54-inch Mower 60-inch Mower Deck Deck Deck Toro Part No. Toro Part No. Toro Part No. 127-0074 127-0075 127-0076 g201893 Figure 24 1. Blower latch g201516... -
Page 16: Installing The Discharge Tubes
Installing the Discharge Tubes Parts needed for this procedure: Upper tube Screw (1/4 x 3/4 inches) Washer (1/4 inch) Locknut (1/4 inch) Lower tube g201513 Figure 26 Procedure 1. Blower pulley 5. Idler arm Important: Make sure that the mower deck is in the 2. - Page 17 G018440 g018440 Figure 29 1. Upper tube 3. Bagger hood 2. Rubber seal protruding out 12. Align the upper tube holes to match the dimples on the surface of the lower tube. Note: Ensure that the side profile appears as shown G018444 g018444 Figure...
- Page 18 18. Secure the tubes together with the nuts (1/4 inch) as shown in Figure 19. Insert the upper discharge tube through the tube seal in the hood. 20. Pull the upper tube out slightly so that the seal extends outward and over the blower assembly (Figure 29).
-
Page 19: Operation
Operation Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. •... -
Page 20: Removing The Bagger
3. Shut off the engine and remove the key. 4. Empty the bags. 5. Unlatch the lower tube. 6. Remove the tubes from the bagger. 7. Use a stick or similar object, not your hands, to remove and clear the obstruction from the tube assembly. Note: In most cases, you can shake the debris out of the tubes. -
Page 21: Operating Tips
Operating Tips CAUTION As the bagger fills, extra weight is added to the back Tips for Bagging of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. Remembering the Size of the •... -
Page 22: Maintenance
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Maintenance Procedure Interval • Inspect the blower belt. After the first 8 hours • Inspect the bagger. • Clean the hood screen. After each use •... -
Page 23: Cleaning The Bagger And Bags
Cleaning the Bagger and 4. Remove the blower from the mower deck. 5. Remove the existing bagger belt from the blower Bags pulleys. Service Interval: After each use 6. Install the new belt around the blower pulleys (Figure 34). 1. Wash the inside and outside of the bagger hood, bags, tube, and the underside of the mower. -
Page 24: Inspecting The Bagger
Inspecting the Bagger Storage Service Interval: Every 100 hours Storing the Bagger After the first 8 hours Attachment 1. Check the upper tube, lower tube, bagger hood, and the blower assembly. 1. Clean the bagger attachment; refer to Cleaning the Note: Replace these parts if they are cracked or Bagger Attachment. -
Page 25: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action There is abnormal vibration. 1. The cutting blade(s) are bent or 1. Install new cutting blade(s). unbalanced. 2. The blade-mounting bolt is loose. 2. Tighten the blade-mounting bolt. 3. There is a loose blower pulley or pulley 3. - Page 26 Notes:...
- Page 27 The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
- Page 28 • The Toro GTS Starting Guarantee does not apply when the product is used commercially. Repairs or adjustments to correct starting difficulties due to the following: Some engines used on Toro Products are warranted by the engine manufacturer.